Murata-Electronics-BLM18HD471SN1D
| Part # | Murata-Electronics-BLM18HD471SN1D |
Download  | Murata-Electronics-BLM18HD471SN1D |
Spec. No. JENF243A-0004P-01
P1/8
Reference Only
GHz Noise Suppression Chip Ferrite Bead
BLM18H
□□□□
SN1
□
Reference Specification
1. Scope
This reference specification applies to Chip Ferrite Bead BLM18H_SN Series.
2. Part Numbering
(ex.) BL
(1)
M
(2)
18
(3)
HG
(4)
601
(5)
S
N
1
(8)
D
(9)
(6) (7)
(1)Product ID
(2)Type (3)Dimension(L×
Ｗ
) (4)Characteristics (5)Typical
Impedance at 100MHz
(6)Performance (7)Category (8)Numbers
of Circuit
(9)Packaging(D:Taping / B:Bulk)
3. Rating
(Note)
Rated Current
(mA)
DC Resistance
Impedance (
)
(Under Standard
T
e
sting Condition)
(
max. )
Customer
Part Number
MURATA
Part Number
Remark
Values
After
at 1GHz
at
at
Initial
at 100MHz
85
℃
125
℃
Values
Typical
T
e
sting
BLM18HE601SN1D
BLM18HE601SN1B
BLM18HE102SN1D
BLM18HE102SN1B
BLM18HE152SN1D
BLM18HE152SN1B
BLM18HG471SN1D
BLM18HG471SN1B
BLM18HG601SN1D
BLM18HG601SN1B
BLM18HG102SN1D
BLM18HG102SN1B
BLM18HD471SN1D
BLM18HD471SN1B
BLM18HD601SN1D
BLM18HD601SN1B
BLM18HD102SN1D
BLM18HD102SN1B
BLM18HB121SN1D
BLM18HB121SN1B
BLM18HB221SN1D
BLM18HB221SN1B
BLM18HB331SN1D
BLM18HB331SN1B
BLM18HK331SN1D
BLM18HK331SN1B
BLM18HK471SN1D
BLM18HK471SN1B
BLM18HK601SN1D
BLM18HK601SN1B
BLM18HK102SN1D
BLM18HK102SN1B
*
1
800
*
1
600
600±25%
1000±25%
1500±25%
470±25%
600±25%
1000±25%
470±25%
600±25%
300 min.
600
0.25
0.35
0.50
0.85
1.0
0.30
For
*
1
600
*
1
500
500 min.
1000
750 min.
1500
0.40 Large
Current
*
1
500
*
1
400
0.55
400 min.
450 min.
600
700
200
0.95
For
1.1 general
use
200
100
100
100
50
750 min.
1000
700 min.
1000
850 min.
1200
1.6
1.7
1.3
1.6
1.2
1.5
1000±25% 1100
min. 1700
1.8
0.5
1.9
0.6
0.9
1.3
0.6
0.8
1.0
1.6
For
high speed
signal line
120±25%
220±25%
330±25%
330±25%
470±25%
600±25%
1000±25%
500±40%
1100±40%
1600±40%
400±40%
600±40%
700±40%
1200±40%
200
100
50
0.8
1.2
200
200
100
50
0.5
0.7
For
Digital
Interface
0.9
1.5
Operating
T
e
mperature : -55°C to +125°C
Storage
T
e
mperature : -55°C to +125°C
MURATA MFG.CO., LTD.
Spec. No. JENF243A–0004N-01
P 2/ 8
Reference Only
Rated current
at 85°C
(Note) As for the Rated current marked with
*
1,
Rated Current is derated as right figure
depending on the operating temperature.
Rated current
at 125°C
0
85
125
Operating Temperature (°C)
4. Style and Dimensions
1.6±0.15
0.8±0.15
■
Equivalent Circuit
0.4±0.2
Resistance element becomes
dominant at high frequencies.
(
)
: Electrode
■
Unit Mass (Typical value)
(in mm)
0.005g
5. Marking
No marking.
6. Standard Testing Conditions
Unless otherwise specified
T
e
mperature : Ordinary
T
e
mp. (15 °C to 35 °C )
In case of doubt
T
e
mperature : 20°C±2 °C
Humidity : Ordinary Humidity (25%(RH) to 85%(RH))
Humidity : 60%(RH) to 70%(RH)
Atmospheric pressure : 86kPa to 106kPa
7. Specifications
7-1. Electrical Performance
No. Item
Specification
Meet item 3.
T
e
st Method
7-1-1 Impedance
Measuring Frequency : 100MHz±1MHz , 1GHz±1MHz
Measuring Equipment : Agilent 4291A or the equivalent
T
e
st Fixture : Agilent 16192A or the equivalent
Measuring Equipment : Digital multi meter
7-1-2 DC
Resistance
Meet item 3.
7-2. Mechanical Performance
No. Item
Specification
T
e
st Method
7-2-1 Appearance
and Meet
item 4.
Dimensions
Visual Inspection and measured with Slide Calipers.
7-2-2 Bonding
Strength
Meet
T
a
ble 1.
It shall be soldered on the substrate.
Applying Force(F) : 6.8N
T
a
ble 1
Applying Time : 5s±1s
Applied direction:Parallel to substrate
Appearance No
damage
Impedance
Side view
Change
(at 100MHz)
DC
Within ±30%
Ｆ
Ｆ
R0.5
Meet item 3.
Resistance
Substrate
MURATA MFG CO., LTD.
Spec. No. JENF243A–0004N-01
P 3/ 8
Reference Only
T
e
st Method
No.
Item
Specification
7-2
ｰ
3Bending
Meet
T
a
ble 1.
It shall be soldered on the substrate.
Substrate: Glass-epoxy 100mm
40mm
1.0mm
Deflection : 2.0mm
Strength
Speed of Applying Force : 0.5mm/s
Keeping Time : 30s
Pressure jig
R340
F
Deflection
Product
45mm
45mm
7-2
ｰ
4Vibration
It shall be soldered on the substrate.
Oscillation Frequency : 10Hz to 55Hz to 10Hz for 1 min
T
o
tal Amplitude : 1.5mm
T
e
sting Time : A period of 2 hours in each of 3 mutually
perpendicular directions. (
T
o
tal 6 h)
Pre-Heating : 150°C±10°C, 60s
～
90s
Solder : Sn-3.0Ag-0.5Cu
7-2-5 Resistance
to Soldering
Heat
Solder
T
e
mperature : 270°C±5°C
Immersion Time : 10s±0.5s
Immersion and emersion rates : 25mm/s
Then measured after exposure in the room condition for
48h±4h.
7-2
ｰ
6Drop
Products shall be no failure
after tested.
It shall be dropped on concrete or steel board.
Method : free fall
Height : 75cm
Attitude from which the product is dropped : 3 direction
The number of times : 3 times for each direction
(
T
o
tal 9 times)
7-2-7 Solderability
The electrodes shall be at
least 95% covered with new
solder coating.
Flux : Ethanol solution of rosin,25(wt)%
Pre-Heating : 150°C±10°C, 60s
～
90s
Solder : Sn-3.0Ag-0.5Cu
Solder
T
e
mperature : 240°C±5°C
Immersion Time : 3s±1s
Immersion and emersion rates : 25mm/s
7-3. Environmental Performance
It shall be soldered on the substrate.
No.
Item
Specification
Meet
T
a
ble 1.
T
e
st Method
7-3-1
T
e
mperature
Cycle
1 cycle:
1 step:-55 °C(+0 °C,-3 °C) / 30min±3min
2 step:Ordinary temp. / 10min to 15min
3 step:+125 °C(+3 °C,-0 °C) / 30min±3min
4 step: Ordinary temp. / 10min to 15min
T
o
tal of 100 cycles
Then measured after exposure in the room condition for
48h±4h.
7-3-2 Humidity
T
e
mperature : 40°C±2°C
Humidity : 90%(RH) to 95%(RH)
Time : 1000h(+48h,-0h)
Then measured after exposure in the room condition for
48h±4h.
MURATA MFG CO., LTD.
Spec. No. JENF243A–0004N-01
P 4/ 8
Reference Only
T
e
st Method
No.
Item
Specification
7-3-3 Heat
Life
Meet
T
a
ble 2.
T
e
mperature : 125°C±3°C
T
a
ble 2
Appearance No
damage
Applying Current : Rated Current (at 125°C)
Time : 1000h(+48h,-0h)
Then measured after exposure in the room condition for
48h±4h.
Impedance
Change
(at 100MHz)
DC
Within ±30%
(for BLM18HE
Within ±40%)
Meet item 3.
Resistance
7-3-4 Cold
Resistance Meet
T
a
ble 1.
T
e
mperature : -55±2°C
Time : 1000h(+48h,-0h)
Then measured after exposure in the room condition for
48h±4h.
8. Specification of Packaging
8-1. Appearance and Dimensions
(8mm-wide paper tape)
2.0±0.
05
1.
5
+0.1
4.0±0.1
4.0±0.1
-0
(in mm)
1.05±0.1
1.1max.
Direction of feed
(1)
T
a
ping
Products shall be packaged in the cavity of the base tape of 8mm-wide,4mm-pitch continuously and sealed
by top tape and bottom tape.
(2) Sprocket hole
The sprocket holes are to the right as the tape is pulled toward the user.
(3) Spliced point
The base tape and top tape have no spliced point
(4) Cavity
There shall not be burr in the cavity.
(5) Missing components number
Missing components number within 0.1% of the number per reel or 1 pc., whichever is greater, and are not
continuous. The specified quantity per reel is kept.
8-2. Tape Strength
(1) Pull Strength
T
o
p tape
5N min.
Bottom tape
(2) Peeling off force of
T
o
p tape
Top tape
165 to 180 degree
0.1N to 0.6N (Minimum value is typical.)
*Speed of Peeling off:300mm/min
F
Bottom tape
Base tape
8-3. Taping Condition
(1) Standard quantity per reel
Quantity per 180mm reel: 4000 pcs. / reel
(2) There shall be leader-tape (top tape and empty tape ) and trailer- tape(empty tape) as follows.
(3) On paper tape, the top tape and the base tape shall not be adhered at the tip of the empty leader tape for more
than 5 pitch.
MURATA MFG CO., LTD.
Spec. No. JENF243A–0004N-01
(4) Marking for reel
P 5/ 8
Reference Only
The following items shall be marked on a label and the label is stuck on the reel.
(Customer part number, MURATA part number, Inspection number(
1), RoHS marking (
2), Quantity, etc)
1) « Expression of Inspection No. »
□□
OOOO
(1)
(2)
(3)
(1)
Factory Code
(2)
Date
First digit
:
Y
e
ar
/ Last digit of year
Second digit
Third, Fourth digit : Day
: Month / Jan. to Sep.
1 to 9, Oct. to Dec.
O, N, D
(3)
Serial No.
2) « Expression of RoHS marking »
ROHS – Y (
△
)
(1) (2)
(1)
RoHS regulation conformity parts.
(2)
MURATA classification number
(5) Outside package
These reels shall be packed in the corrugated cardboard package and the following items shall be marked on
a label and the label is stuck on the box.
(Customer name, Purchasing Order Number, Customer Part Number, MURATA part number,
RoHS marking (
2) , Quantity , etc)
(6) Dimensions of reel and taping(leader-tape, trailer-tape)
Leader
Trailer
160 min.
2.0±0.5
190 min.
210 min.
Label
Empty tape
Top tape
13.0±0.2
60±
1
0
9±
1
0
13±1.4
21.0±0.8
Direction of feed
180
±
0
3
(in mm)
8-4. Specification of Outer Case
Outer Case Dimensions
(mm)
Standard Reel Quantity in Outer Case
(Reel)
Label
W
D
H
H
186
186
93
5
Above Outer Case size is typical. It depends on a quantity of an
order.
D
W
9.
! Caution
9-1.Surge current
Excessive surge current (pulse current or rush current) than specified rated current applied to the product may
cause a critical failure, such as an open circuit, burnout caused by excessive temperature rise.
Please contact us in advance in case of applying the surge current.
9-2. Limitation of Applications
Please contact us before using our products for the applications listed below which require especially high
reliability for the prevention of defects which might directly cause damage to the third party’s life, body or property.
(1)Aircraft equipment
(4)Power plant control equipment
(5)Medical equipment
(6)Disaster prevention / crime prevention equipment
(7)Traffic signal equipment
(8)Transportation equipment (vehicles, trains, ships, etc.)
(9)Applications of similar complexity and /or reliability requirements to the applications listed in the above
(2)Aerospace equipment
(3)Undersea equipment
MURATA MFG CO., LTD.
Spec. No. JENF243A–0004N-01
P 6/ 8
Reference Only
10. Notice
This product is designed for solder mounting.
Please consult us in advance for applying other mounting method such as conductive adhesive.
10-1. Land pattern designing
Standard land dimensions (Flow and Reflow soldering)
Chip Ferrite Bead
Soldering
Flow
Reflow
a
b
c
c
2.2 to 2.6
1.8 to 2.0
0.7
0.7
a
b
Solder Resist
Pattern
(in mm)
10-2. Soldering Conditions
Products can be applied to reflow and flow soldering.
(1) Flux,Solder
Flux
Use rosin-based flux, but not highly acidic flux (with chlorine content exceeding 0.2(wt)%. )
Do not use water-soluble flux.
Solder
Use Sn-3.0Ag-0.5Cu solder
Standard thickness of solder paste : 100 µm to 200
m
(2) Soldering conditions
Pre-heating should be in such a way that the temperature difference between solder and ferrite surface is limited
to 150
℃
max. Also cooling into solvent after soldering should be in such a way that the temperature difference
is limited to 100
℃
max.
Insufficient pre-heating may cause cracks on the ferrite, resulting in the deterioration of product quality.
Standard soldering profile and the limit soldering profile is as follows.
The excessive limit soldering conditions may cause leaching of the electrode and / or resulting in the
deterioration
of product quality.
□
Flow soldering profile
Temp.
(
℃)
265℃±3℃
250℃
Limit Profile
150
Heating Time
Standard Profile
60s min.
Time.
(
s)
Standard Profile
150°C, 60s min.
250°C, 4s~6s
2 times
Limit Profile
Pre-heating
Heating
Cycle of flow
265°C±3°C, 5s max.
2 times
MURATA MFG CO., LTD.
Spec. No. JENF243A–0004N-01
P 7/ 8
Reference Only
□
Reflow soldering profile
Temp.
(
℃)
260℃
245℃±3℃
230℃
220℃
Limit Profile
180
150
Standard Profile
30s
～60
s
60s max.
90s±30s
Time.
(
s)
Standard Profile
Limit Profile
Pre-heating
Heating
Peak temperature
150°C~180°C, 90s±30s
above 220°C, 30s~60s
245°C±3°C
above 230°C, 60s max.
260°C, 10s
Cycle of reflow
2 times
2 times
10-3. Reworking with soldering iron
Pre-heating: 150°C, 1 min
Soldering iron output: 80W max.
Tip diameter:
φ
3mm max.
Tip temperature: 350°C max.
Soldering time : 3(+1,-0) seconds.
Times : 2times max.
Note :Do not directly touch the products with the tip of the soldering iron in order to prevent the crack
on the ferrite material due to the thermal shock.
10-4. Solder Volume
Solder shall be used not to be exceed as shown below.
Upper Limit
Recommendable
1/3T
≦
t
≦
T
(
T
:
C
hip thickness)
t
Accordingly increasing the solder volume, the mechanical stress to product is also increased.
Exceeding solder volume may cause the failure of mechanical or electrical performance.
10-5. Attention regarding
P
.
C.B. bending
The following shall be considered when designing and laying out
P
.
C.B.’s.
(1)
P
.
C.B. shall be designed so that products are not subject to the mechanical stress for board warpage.
<Products direction>
a
Products shall be located in the sideways
b
direction (Length: a
b) to the mechanical
stress.
Poor example
〈
〉
Good example
〈
〉
(2)Products location on
P
.
C.B. separation.
Products (A, B, C, D) shall be located carefully
so that products are not subject to the
mechanical stress due to warping the board.
Because they may be subjected the mechanical
stress in order of A
C
B
D.
C
B
Seam
D
A
a
b
Slit
Length:a b
10-6. Mounting density
Add special attention to radiating heat of products when mounting the inductor near the products with heating.
The excessive heat by other products may cause deterioration at joint of this product with substrate.
MURATA MFG CO., LTD.
Spec. No. JENF243A–0004N-01
P 8/ 8
Reference Only
10-7. Operating Environment
Do not use this product under the following environmental conditions, on deterioration of the Insulation
Resistance of the Ferrite material and/or corrosion of Inner Electrode may result from the use.
(1) in the corrodible atmosphere (acidic gases, alkaline gases, chlorine, sulfur gases, organic gases and etc. )
(2) in the atmosphere where liquid such as organic solvent, may splash on the products.
(3) in the atmosphere where the temperature / humidity changes rapidly and it is easy to dew.
10-8. Resin coating
The impedance value may change and/or it may affect on the product’s performance due to high cure-stress of
resin to be used for coating / molding products. So please pay your careful attention when you select resin. In
prior to use, please make the reliability evaluation with the product mounted in your application set.
10-9. Cleaning Conditions
Products shall be cleaned on the following conditions.
(1)Cleaning temperature shall be limited to 60°C max. (40°C max. for IPA)
(2)Ultrasonic cleaning shall comply with the following conditions, avoiding the resonance phenomenon at the
mounted products and
P
.
C.B.
Power : 20W/l max.
(3)Cleaner
Frequency : 28kHz to 40kHz
Time : 5 min max.
1.Cleaner
Isopropyl alcohol (IPA)
2.Aqueous agent
PINE ALPHA ST-100S
(4)There shall be no residual flux and residual cleaner after cleaning.
In the case of using aqueous agent, products shall be dried completely after rinse with de-ionized water in
order to remove the cleaner.
(5)Other cleaning
Please contact us.
10-10. Handling of a substrate
After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to
the substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening
screw to the substrate.
Excessive mechanical stress may cause cracking in the product.
Bending
Twisting
10-11. Storage Conditions
(1)Storage period
Use the products within 6 months after delivered.
Solderability should be checked if this period is exceeded.
(2)Storage conditions
Products should be stored in the warehouse on the following conditions.
T
e
mperature : -10°C to 40°C
Humidity
: 15% to 85% relative humidity
No rapid change on temperature and humidity
Don’t keep products in corrosive gases such as sulfur, chlorine gas or acid, or it may cause oxidization
of electrode, resulting in poor solderability.
Products should be stored on the palette for the prevention of the influence from humidity, dust and so on.
Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on.
Products should be stored under the airtight packaged condition.
(3)Delivery
Care should be taken when transporting or handling product to avoid excessive vibration or mechanical shock.
11
!
Notes
(1) Please make sure that your product has been evaluated in view of your specifications with our product
being mounted to your product.
(2)
Y
o
u are requested not to use our product deviating from the reference specifications.
(3) The contents of this reference specification are subject to change without advance notice. Please approve our
product specifications or transact the approval sheet for product specifications before ordering.
MURATA MFG CO., LTD.
