Phoenix-Contact-2909530
| Part # | Phoenix-Contact-2909530 |
Download  | Phoenix-Contact-2909530 |
Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user’s
documentation. Our General Terms of Use for Downloads are valid
(http://phoenixcontact.com/download)
PLC-INTERFACE, consisting of DIN-rail-mountable basic terminal block in 6.2 mm with Push-in connection
and plug-in miniature relay with 6 A power contact, 1 changeover contact, 230 V AC/220 V DC input voltage.
Approved according to ATEX/IECEx (Zone 2) and Ex Zone Class I, Div. 2.
Key Commercial Data
Packing unit
10 pc
10 pc
Minimum order quantity
GTIN
GTIN
4055626363677
Technical data
Note
EMC: class A product, see manufacturer’s declaration in the download
area
Utilization restriction
Dimensions
Width
Height
Depth
6.2 mm
80 mm
94 mm
Ambient conditions
Ambient temperature (operation)
-20 °C … 60 °C (UL)
-40 °C … 55 °C (ATEX / IECEx)
-40 °C … 85 °C
Ambient temperature (storage/transport)
Degree of protection
IP20 (Relay base)
Coil side
Nominal input voltage U
N
230 V AC
220 V DC
Typical input current at U
N
3.2 mA (U
N
= 230 V AC)
03/12/2021 Page
1 / 15
Technical data
Coil side
3 mA (U
N
= 220 V DC)
Typical response time
7 ms
Typical release time
15 ms
Protective circuit
Bridge rectifier Bridge rectifier
Yellow LED
Operating voltage display
Power dissipation for nominal condition
0.74 W
Contact side
Contact type
1 changeover contact
Single contact
AgSnO
Type of switch contact
Contact material
250 V AC/DC (The separating plate PLC-ATP should be installed for
voltages larger than 250 V (L1, L2, L3) between identical terminal blocks
in adjacent modules. Potential bridging is then carried out with FBST 8-
PLC… or …FBST 500…)
Maximum switching voltage
Minimum switching voltage
Min. switching current
5 V (at 100 mA)
10 mA (at 12 V)
Maximum inrush current
10 A (4 s)
Limiting continuous current
Interrupting rating (ohmic load) max.
6 A
140 W (at 24 V DC)
20 W (at 48 V DC)
18 W (at 60 V DC)
23 W (at 110 V DC)
40 W (at 220 V DC)
1500 VA (for 250 V AC)
2 A (at 24 V, DC13)
0.2 A (at 110 V, DC13)
0.1 A (at 220 V, DC13)
3 A (at 24 V, AC15)
3 A (at 120 V, AC15)
3 A (at 230 V, AC15)
Switching capacity
General
Test voltage
4 kV AC (50 Hz, 1 min., winding/contact)
100% operating factor
Operating mode
Flammability rating according to UL 94
Mechanical service life
Mounting position
V0 (Housing)
2x 10
7
cycles
any
Assembly instructions
In rows with zero spacing
Connection data
Connection name
Coil side
Connection method
Push-in connection
03/12/2021 Page
2 / 15
Technical data
Connection data
Stripping length
8 mm
Conductor cross section solid
Conductor cross section flexible
0.14 mm² … 2.5 mm²
0.14 mm² … 2.5 mm²
0.2 mm² … 2.5 mm² (Single ferrule)
2x 0.5 mm² … 1 mm² (TWIN ferrule)
26 … 14
Conductor cross section AWG
Connection data 2
Connection name
Contact side
Connection method
Push-in connection
8 mm
Stripping length
Conductor cross section solid
Conductor cross section flexible
0.14 mm² … 2.5 mm²
0.14 mm² … 2.5 mm²
0.2 mm² … 2.5 mm² (Single ferrule)
2x 0.5 mm² … 1 mm² (TWIN ferrule)
26 … 14
Conductor cross section AWG
Standards and Regulations
Designation
Standards/regulations
Standards/regulations
IEC 60664
EN 50178
EN 60079-0, -7, -15
Pollution degree
3
Overvoltage category
III
Conformance/approvals
Designation
Identification
Designation
Identification
Certificate
CE
CE-compliant
ATEX
II 3G Ex ec nC IIC T4 Gc
IBExU16ATEXB015 X
IECEx
Designation
Identification
Certificate
Ex ec nC IIC T4 Gc
IECEx IBE 16.0029X
UL, USA
Designation
Identification
Designation
Identification
Designation
Identification
Designation
Identification
Class I, Zone 2, AEx nA nC IIC T6
UL, USA/Canada
Class I, Div. 2, Groups A, B, C, D
UL, Canada
Class I, Zone 2, Ex nA nC IIC Gc T6 X
Corrosive gas test
ISA-S71.04. G3 Harsh Group
03/12/2021 Page
3 / 15
Technical data
Conformance/approvals
EN 60068-2-60
Environmental Product Compliance
REACh SVHC
China RoHS
Lead 7439-92-1
Environmentally Friendly Use Period = 50 years
For details about hazardous substances go to tab “Downloads”,
Category “Manufacturer’s declaration”
Drawings
Diagram
Diagram
U
U
N
1,4
1,3
1,2
A
1,1
U
N
= 220 V DC / 230 V AC
1
0,9
0,8
B
0,7
20 25 30 35 40 45 50 55 60 65
Interrupting rating
T
[
C]
°
U
Curve A
Maximum permissible continuous voltage U
max
with limiting continuous
current on the contact side (see relevant technical data)
Curve B
Minimum permissible operate voltage U
op
after pre-excitation (see
relevant technical data)
Circuit diagram
A2
A1
11
14
12
Classifications
eCl@ss
eCl@ss 10.0.1
eCl@ss 11.0
27371601
27371601
03/12/2021 Page
4 / 15
Classifications
eCl@ss
eCl@ss 5.0
eCl@ss 5.1
eCl@ss 6.0
eCl@ss 7.0
eCl@ss 9.0
27371600
27371600
27371600
27371601
27371601
ETIM
ETIM 2.0
ETIM 3.0
ETIM 4.0
ETIM 5.0
ETIM 6.0
ETIM 7.0
EC001437
EC001437
EC001437
EC001437
EC001437
EC001437
UNSPSC
UNSPSC 6.01
UNSPSC 7.0901
UNSPSC 11
30211916
39121515
39121515
39121515
39122334
39122334
39122334
39122334
39122334
UNSPSC 12.01
UNSPSC 13.2
UNSPSC 18.0
UNSPSC 19.0
UNSPSC 20.0
UNSPSC 21.0
Approvals
Approvals
Approvals
DNV GL
Ex Approvals
IECEx / UL Listed / cUL Listed / EAC Ex / ATEX / cULus Listed
Approval details
DNV GL
TAE0000196-03
03/12/2021 Page
5 / 15
Accessories
Accessories
Bridge
Continuous plug-in bridge, length: 500 mm, color: red
Continuous plug-in bridge, length: 500 mm, color: blue
Continuous plug-in bridge, length: 500 mm, color: gray
Single plug-in bridge, length: 6 mm, number of positions: 2, color: red
Single plug-in bridge, length: 6 mm, number of positions: 2, color: blue
03/12/2021 Page
6 / 15
Accessories
Single plug-in bridge, length: 6 mm, number of positions: 2, color: gray
Single plug-in bridge, length: 8 mm, number of positions: 2, color: gray
Controller board
V8 adapter for 8 x PLC-INTERFACE (6.2 mm), controller: PLC system cabling of output cards, connection 1: Screw
connection 1x, connection 2: IDC/FLK pin strip 1x 14-position, connection 3: Plug connection (Can be snapped onto
8x PLC-INTERFACE terminals), number of channels: 8, control logic: plusschaltend
V8 adapter for 8 x PLC-INTERFACE (6.2 mm), controller: PLC system cabling of output cards, connection 1: Screw
connection 1x, connection 2: IDC/FLK pin strip 1x 14-position, connection 3: Plug connection (Can be snapped onto
8x PLC-INTERFACE terminals), number of channels: 8, control logic: minusschaltend
V8 adapter for 8 x PLC-INTERFACE (6.2 mm), controller: PLC system cabling of output cards, connection 1: Screw
connection 1x, connection 2: D-SUB pin strip 1x 15-position, connection 3: Plug connection (Can be snapped onto 8x
PLC-INTERFACE terminals), number of channels: 8, control logic: plusschaltend
03/12/2021 Page
7 / 15
Accessories
V8 adapter for 8 x PLC-INTERFACE (6.2 mm), controller: PLC system cabling of output cards, connection 1: Screw
connection 1x, connection 2: D-SUB socket strip 1x 15-position, connection 3: Plug connection (Can be snapped onto
8x PLC-INTERFACE terminals), number of channels: 8, control logic: plusschaltend
DIN rail
DIN rail perforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized,
passivated with a thick layer, length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized,
passivated with a thick layer, length: 2000 mm, color: silver
DIN rail perforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, Galvanized,
white passivated, length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, Galvanized,
white passivated, length: 2000 mm, color: silver
03/12/2021 Page
8 / 15
Accessories
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Aluminum,
uncoated, length: 2000 mm, color: silver
DIN rail perforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized,
length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized,
length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Copper, uncoated,
length: 2000 mm, color: copper-colored
DIN rail end piece, for DIN rail NS 35/7.5
03/12/2021 Page
9 / 15
Accessories
DIN rail perforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel, galvanized,
passivated with a thick layer, length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel,
galvanized, passivated with a thick layer, length: 2000 mm, color: silver
DIN rail perforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel, Galvanized,
white passivated, length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel,
Galvanized, white passivated, length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Aluminum,
uncoated, length: 2000 mm, color: silver
03/12/2021 Page
10 / 15
Accessories
DIN rail perforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel, galvanized,
length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel,
galvanized, length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Copper,
uncoated, length: 2000 mm, color: copper-colored
DIN rail end piece, for DIN rail NS 35/15
DIN rail, unperforated, Standard profile 2.3 mm, width: 35 mm, height: 15 mm, acc. to EN 60715, material: Steel,
galvanized, passivated with a thick layer, length: 2000 mm, color: silver
Labeled terminal marker
03/12/2021 Page
11 / 15
Accessories
Zack marker strip, can be ordered: Strip, white, labeled according to customer specifications, mounting type: snap
into tall marker groove, for terminal block width: 6.2 mm, lettering field size: 6.15 x 10.5 mm, Number of individual
labels: 10
Zack marker strip, Strip, white, labeled, can be labeled with: CMS-P1-PLOTTER, printed horizontally: consecutive
numbers 1 … 10, 11 … 20, etc. up to 491 … 500, mounting type: snap into tall marker groove, for terminal block width:
6.2 mm, lettering field size: 6.15 x 10.5 mm, Number of individual labels: 10
Zack marker strip, Strip, white, labeled, can be labeled with: CMS-P1-PLOTTER, Printed vertically: consecutive
numbers 1 … 10, 11 … 20, etc. up to 491 … 500, mounting type: snap into tall marker groove, for terminal block width:
6.2 mm, lettering field size: 6.15 x 10.5 mm, Number of individual labels: 10
Zack marker strip, Strip, white, labeled, can be labeled with: CMS-P1-PLOTTER, printed horizontally: Identical
numbers 1 or 2, etc. up to 100, mounting type: snap into tall marker groove, for terminal block width: 6.2 mm, lettering
field size: 6.15 x 10.5 mm, Number of individual labels: 10
Marker for terminal blocks, Strip, white, labeled, can be labeled with: CMS-P1-PLOTTER, horizontal: L1, L2, L3, N,
PE, L1, L2, L3, N, PE, mounting type: snap into tall marker groove, for terminal block width: 6.2 mm, lettering field
size: 6.15 x 10.5 mm, Number of individual labels: 10
03/12/2021 Page
12 / 15
Accessories
Marker for terminal blocks, Strip, white, labeled, can be labeled with: CMS-P1-PLOTTER, printed horizontally: U, V,
W, N, GND, U, V, W, N, GND, mounting type: snap into tall marker groove, for terminal block width: 6.2 mm, lettering
field size: 6.15 x 10.5 mm, Number of individual labels: 10
Marker for terminal blocks, can be ordered: by sheet, white, labeled according to customer specifications, mounting
type: snap into tall marker groove, for terminal block width: 6.2 mm, lettering field size: 5.6 x 10.5 mm, Number of
individual labels: 80
Marker for terminal blocks, can be ordered: by sheet, white, labeled according to customer specifications, mounting
type: snap into tall marker groove, for terminal block width: 6.2 mm, lettering field size: 5.6 x 10.5 mm, Number of
individual labels: 60
Partition plate
Separating plate, 2 mm thick, required at the start and end of a PLC terminal strip. Furthermore, it is used for: visual
separation of groups, safe isolation of different voltages of neighboring PLC relays in acc. with DIN VDE 0106-101,
isolation
Power module
Power terminal block, for the input of up to four potentials, for mounting on NS 35/7.5
Screwdriver tools
03/12/2021 Page
13 / 15
Accessories
Actuation tool, for ST terminal blocks, also suitable for use as a bladed screwdriver, size: 0.6 x 3.5 x 100 mm, 2-
component grip, with non-slip grip
Terminal marking
Zack marker strip, Strip, white, unlabeled, can be labeled with: PLOTMARK, CMS-P1-PLOTTER, mounting type:
snap into tall marker groove, for terminal block width: 6.2 mm, lettering field size: 6.15 x 10.5 mm, Number of
individual labels: 10
Marker for terminal blocks, Sheet, white, unlabeled, can be labeled with: BLUEMARK ID COLOR, BLUEMARK ID,
BLUEMARK CLED, PLOTMARK, CMS-P1-PLOTTER, mounting type: snap into tall marker groove, for terminal block
width: 6.2 mm, lettering field size: 5.6 x 10.5 mm, Number of individual labels: 80
Marker for terminal blocks, Sheet, white, unlabeled, can be labeled with: TOPMARK NEO, TOPMARK LASER,
BLUEMARK ID COLOR, BLUEMARK ID, BLUEMARK CLED, THERMOMARK PRIME, THERMOMARK CARD 2.0,
THERMOMARK CARD, mounting type: snap into tall marker groove, for terminal block width: 6.2 mm, lettering field
size: 5.6 x 10.5 mm, Number of individual labels: 60
Spare parts
Plug-in miniature power relay, with power contact, 1 changeover contact, input voltage 60 V DC
03/12/2021 Page
14 / 15
Phoenix Contact 2021 © – all rights reserved
PHOENIX CONTACT GmbH & Co. KG
Flachsmarktstr. 8
32825 Blomberg
Germany
Tel. +49 5235 300
Fax +49 5235 3 41200
03/12/2021 Page
15 / 15
