EMTEK-BLN2012-750-2P-T1
| Part # | EMTEK-BLN2012-750-2P-T1 |
Download  | EMTEK-BLN2012-750-2P-T1 |
PRODUCT SPECIFICATION
SPEC. NO:
T-0634-003K
新弘智
DATE: Jul.26,2018
CUSTOMER’S PRODUCT NAME:
EMTEK PRODUCT NAME:
BLN2012-750-2P-T1
THIS SPECIFICATION IS:
□
FULLY ACCEPTED
□
DENIED
□
ACCEPTED UNDER THE FOLLOWING CONDITIONS
SIGNATURE:
NAME(PRINT):
TITLE:
DATE:
FACTORY:
本文件內容全部或部份,未經兆欣科技股份有限公
司同意不得以任何形式複製或其他用途
39,Chingao Rd.,(305)Hsinpu,
Hsinchu Hsien,Taiwan,R.O.C
TEL: 03-5894-433
All rights reserved.This document or parts thereof,may
not be reproduced by any means or used in any manner
witout written permission of EMTEK CO.,LTD.
FAX: 03-5894-523
1/9
SPEC. No.
T-0634-003K
PRODUCT SPECIFICATION
1. Scope
This specification applies Micro Chip Transformers BLN2012-750-2P-T1 to be delivered to user.
1:1 Broad Band Baluns For TV Tuner Apprications
1-1 Features
1. Ultra Miniture Wire Wound Transformer (2.0 x 1.2 x 1.2mm)
2. Low Insertion Loss
3. Wideband Frequency Range
4. Srface Mount
1-2 Apprications
TV tuners, Cable TV tuners and Comunication apprications that require
unbalance mode to balance mode conversion.
2. Product Identification
BLN 2012 – 750 – 2P – T1
(1) (2)
(3) (4) (5)
(1) Product name
(2) Shapes and dimensions
(3) Impedance
750:75Ω
(4) Number of Line
：
2P: 2-Line
(5) Taping Type
3. Shapes and Dimensions
A
B
Epoxy
A : 2.0 ± 0.2
mm
B : 1.2 ± 0.2
mm
C : 1.2 ± 0.2
mm
Terminations
Wires
④
①
(0.4)
(0.4)
③
②
Drawn by
Checked by
Approved by
(0.45)
(0.45)
2/9
SPEC. No.
PRODUCT SPECIFICATION
T-0634-003K
4. Equivalent Circuit
(1)
(2)
(4)
(3)
5. Electrical Characterisitcs
5-1 Electrical Spec.
Frequency Unbalance
Balance
Insertion
CMRR Rated
Rated Withstand
Insulation
Our Product Part Number
BLN2012-750-2P-T1
Range
(MHz)
Impedance Impedance
Loss(dB)
(dB)
Typ.
Current Voltage
Voltage Resistance
(Ω)
75
(Ω)
75
Typ.
1.5
(mA)
200
(V)
50
(V)
(MΩ)
10
50~870
20
125
BLN2012-750-2P-T1
10000
1000
100
Z (common
mode)
Z(differential
mode)
10
1
1
10
100
1000
10000
Frequency(MHz)
3/9
SPEC. No.
PRODUCT SPECIFICATION
T-0634-003K
Insertion Loss(Reference)
CMRR(Reference)
4/9
SPEC. No.
PRODUCT SPECIFICATION
T-0634-003K
5-2 Test Equipment
5-2-1 Impedance
Measured by using Agilent E4991A RF Impedance Analyzer.
5-2-2 DC Resistance
Measured by using Chroma 16502 mill ohm meter.
5-2-3 Insulation Resistance
Measured by using Chroma 19073
Measurement voltage : 50V
5/9
SPEC. No.
PRODUCT SPECIFICATION
T-0634-003K
6. Reliability Test
Operating temperature : -40 to +105
℃
Storage temp and humidity : 20~25
℃
60%RH max.
Item
Solder ability
Specifications
It can be connected on the
Recommendation soldering
condition.
Test conditions
Apply cream solder to the test circuit board .
It is mounted on the recommendation soldering
condition.
The terminal electrode and the
ferrite must not be damaged.
Solder a chip to test substrate
, and then laterally
apply a load 0.5Kg in the arrow direction.
Terminal
strength
The terminal electrode and the
ferrite must not be damaged.
Soldering a chip to a test substrate ,
Strength on
PC Board
bending
bend the substrate by 2mm and then return.
45
45
Width side
40
100
length
6/9
SPEC. No.
T-0634-003K
PRODUCT SPECIFICATION
Item
Specifications
Test conditions
20
10
Force
Dimensions in mm
R10
Test board : Glass base epoxy multiplayer board pc board pattern.
PC board pattern : Recommended PC board pattern.
High
temperature
resistance
Appearance : Ferrite shall not be
Temperature : +105±2
℃
damaged. Applied
voltage : Rated voltage
Impedance : Within ±20% of the
Applied current : Rated current
initial value.
Testing time : 50±12 hours
insulation resistance: >10(MΩ)
DC resistance : standard value
inside.
Measurement : After placing for 24 hours min.
Humidity
resistance
Temperature : +85±2
℃
Humidity : 40 to 60%RH
Applied current : Rated current
Applied voltage : Rated voltage
Testing time : 500±12 hours
Measurement : After placing for 24 hours min.
Temperature : -25
℃
,+85
℃
kept stabilized for 30 minutes each.
Cycle : 5 cycle
Thermal cycle
Measurement : After placing for 24 hours min.
1 cycle
30 min.
+105
℃
3 min.
-40
℃
30 min.
7/9
SPEC. No.
T-0634-003K
PRODUCT SPECIFICATION
Item
Specifications
Test conditions
Low
Temperature :
-40±2
℃
Testing time : 48±12 hours
temperature
resistance
Measurement : After placing for 24 hours min.
Frequency : 10 to 50 Hz
Vibration
Appearance : Ferrite shall not be
damaged.
Amplitude : 1.52 mm
Dimension and times : X ,Y and Z directions
for 2 hours each.
7. Packaging
The packaging must be done not to receive any damage during transporting and storing.
7-1 Tape dimensions
Ko
P
1
P
0
P
W
Bo
t
Ao
( Dimensions in mm; Tolerance
：
±0.1)
P
0
P
1
2
Symbol
W
8
P
4
Ao
1.6
Bo
Ko
t
Dimension
4
2.42
1.14
0.22
7-2 Reel dimensions
D
( Dimensions in mm )
Symbol
T
180
60
A
B
C
D
E
C
A
B
13
14.4
8.4
E
8/9
SPEC. No.
PRODUCT SPECIFICATION
T-0634-003K
7-3 Tapping figure
Top cover tape
Carrier tape
Sprocket hole
Cavity (chip insert)
7-4 Packaging Form
There shall not continuation more than two vacancies of the product.
Material of carrier tape : Polystyrene
Material of cover tape : Polyester
7-5 Cover Tape Peel Strength
The force for tearing off cover tape is 0.05~0.69(N) in the arrow direction at the following conditions:
Temperature : 5 ~ 35
℃
Humidity : 45 ~ 85%
Atmospheric pressure : 860 ~ 1060 hpa
7-6 Packing Quantity
φ180 mm reel T type : 2000 pcs./reel
9/9
SPEC. No.
T-0634-003K
PRODUCT SPECIFICATION
8. Recommended Soldering Conditions
(Please use this product by reflow soldering)
8-1 Recommended Footprint
Termination Number : Please refer to the equivalent circuit in chapter 3.
2.6
1.2
Unit :
1.0
0.8
8-2 Recommended Reflow Pattern
Reflow : until two times.
10sec. Max.
255
℃
217
℃
Natural cooling
150sec Max..
150
℃
60sec. Min.
8-3 Iron Soldering
Use a solder iron of less than 30W when soldering, do not allow the soldering iron tip directly touch
the ferrite body
outside of terminal electrode.
4 seconds max. at 260
℃
.
9. Attention in Case of Using
In case of using product ,please avoid following matters:
Splashing water or salt water
Dew condenses
Toxic gas (Hydrogen sulfide, Sulfurous acid ,Chlorine, Ammonia)
Vibrations or shocks which exceed the specified condition
Please be careful for the stress to this product by board flexure or something after the mounting.
10. Other
Recommended wire wound inductors should be used within 6 months from the time of delivery.
