FUJITSU-FTR-J2AK012W
| Part # | FUJITSU-FTR-J2AK012W |
Download  | FUJITSU-FTR-J2AK012W |
POWER RELAY
ULTRA SMALL HIGH VOLTAGE DC RELAY
FTR-J2 Series
■
FEATURES
•
10A, 450VDC high-voltage switching (2 x 10A, 200VDC switching)
•
Contact voltage drop: typical 0.1V
•
Inrush current 150A (capacitive load)
•
Compact size (L x W X H= 24×23.5x27mm)
•
2 x 1 form A
tween contacts and coil
Insulation distance: Clearance/creepage > 6mm
Dielectric strength: 4 ,000 VAC
Surge strength: 10,000 V (1.2 x 50µsec)
•
Plastic materials conform to UL94 flame class V-0
•
Flux proof, RTII
•
RoHS compliant (Please see page 9 for more information)
■
Part Numbers
[Example]
FTR-J2
(a)
–
A
(b)
K
(c)
012
(d)
W
(e)
(a)
(b)
(c)
(d)
Relay type
Contact configuration
Coil power
FTR-J21 :
FTR-J2 series
A :
2 x 1 form A
K :
Standard sensitivity
012 :
5….110VDC
Coil rating table at page 4
W :
Silver alloy
Coil rated voltage
(e)
Contact material
Actual marking does not carry the type name: “FTR”
E.g.: Ordering code: “
FTR-J2AK012W
“, actual marking: “
J2AK012W
”
1
FTR-J2 Series
■
Specifications
(1/2)
Item
FTR-J2
Remarks / conditions
Contact
Configuration
1 form A x 2
Silver alloy
Max.100
mΩ
data
Material
Resistance
at 1A, 6VDC between contact terminals
Note1
Contact rating
10A, 450VDC (resistive load)
10A, 200VDC (resistive load)
When 2 contacts connected in series
through a common load
When each NO contact is used inde-
pendently
Overload switching
10A, 500VDC (resistive load) 50 ops.
10A, 250VDC (resistive load) 50 ops.
12A per contact
When 2 contacts connected in series
through a common load
When each NO contact is used inde-
pendently
Max. carrying current
Inrush current
2 contacts connected in series through
a common load is counted as 1 contact
Note2
Peak 150A per contact
2 contacts connected in series through
a common load is counted as 1 contact
Note2
Max. switching voltage
600VDC
300VDC
When 2 contacts connected in series
through a common load
When each NO contact is used inde-
pendently
At 10A, between contact terminals
Note1
Contact voltage drop (initial)
Max. 0.1V per contact
Minimum switching load
(reference * )
100mA 5VDC per contact
2 contacts connected in series through
a common load is counted as 1 contact
Note2
Coil
Rated power
530mW
Standard single coil at 20°C (Please
refer to Coil Rating for 2 coils)
Operate voltage
Release voltage
Operating temperature range
Maximum 70% of nominal voltage
Maximum 5% of nominal voltage
-40ºC ~ +85ºC
At 20°C
At 20°C
No frost
Note3
Timing Operate
Max. 15ms (without bounce)
Max. 5ms (without bounce)
Min. 2M operations per contact
At nominal voltage, 20°C, with varistor
data
Release
Life
Mechanical
2 contacts connected in series through
a common load is counted as 1 contact
Note2
Electrical
Min. 10K operations per contact
2 contacts connected in series through
a common load is counted as 1 contact
Note2
Insula- Insulation
resistance (initial)
Min. 1000MΩ at 500VDC
Dielectric
strength
Open
contacts
1000VAC (50/60Hz), 1 minute
Note2
tion
Adjacent
contact
Coil contacts
1000VAC (50/60Hz), 1 minute
Note1
4000VAC (50/60Hz), 1 minute
Note1
Surge strength
Coil to con-
tacts
10000V / 1.2 x 50µm standard wave
Note2
2
FTR-J2 Series
■
Specifications
(2/2)
Vibration resis-
Misoperation
tance
Other
10Hz ~ 55Hz ~ 10Hz single amplitude
Coil ON/OF
F
, 3
a
xes, total 6 cycles
0.75mm
Endurance
10Hz ~ 55Hz ~ 10Hz single amplitude
0.75mm
Coil OF
F
, 3
a
xes, total 6 hours
Shock resis-
tance
Misoperation
Endurance
Min. 200m/s² (11 ± 1ms)
Coil ON/OF
F
, 3
a
xes,
total 36 operations
Coil OF
F
, 3
a
xes,
Min. 1,000m/s² (6 ± 1ms)
total 18 operations
Dimensions / weight
Sealing
23.5 x 24.0 x 27.0 mm / approx. 26g
Flux proof RTII
Values of electrical characteristics are under 15 to 35 degC, 25 to 75%RH, air pressure 86kPa to 106kPa (JIS standard condition) unless otherwise specified.
* Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values
may vary according to switching frequencies, environmental conditions and expected reliability levels.
Note 1: The specification value is applied to each contact in case 2 coils are connected in series through a common load.
Note 2: The contacts connected in series are considered as an integrated contact in case
2 coils are connected in series through a common load.
Note 3: There are cases where the relay does not operate when it is used at high ambient temperature. Please refer to characteristic data and apply adequate coil
voltage.
There would be a possibility that high voltage DC relay loses breaking current ability as one of failure modes.
Please provide fail safeness design on the circuit. To secure safety,
the relay shall not be used in exceeding its specifications including operation life, and
!
handle the relay as a periodic maintenance component.
Relay contact terminals have polarity. Please connect higher potential side of the load to (+). Please refer to recommended circuit layout.
!
Please always use a varistor to protect the coil from back electromotive force. Use of other protection element may shorten relay life excessively.
!
Varistor shall be connected in parallel to the relay coil.
Please refer to recommended circuit layout.
!
Varistor voltage shall have 3 times as high as applied coil voltage.
Care shall be taken on the heat generated on PC board when maximum carrying current exceeds 10A. Please perform the confirmation test with actual
conditions.
!
3
FTR-J2 Series
■
Coil Data
Standard single coil
Coil code
Rated Coil Voltage
Coil Resistance +/-10%
Must Operate Voltage
*
Must Release Voltage
*
Rated Power (W)
(±10%)
(VDC)
5
6
12
24
48
60
110
(Ω)
47
68
270
1,100
4,400
6,790
22,800
(VDC)
3.5
4.2
8.4
16.8
33.6
42.0
77.0
(VDC)
0.25
0.3
0.6
1.2
2.4
3
005
006
012
024
048
060
110
Approx.
0.53
5.5
2 coils in series (Connect relay coil terminal No.2 to No.3) See note 2.
Coil code
Rated Coil Voltage
Coil Resistance +/-10%
Must Operate Voltage
*
Must Release Voltage
*
Rated Power (W)
(±10%)
(VDC)
10
12
24
48
96
120
220
(Ω)
94
136
540
2,200
8,800
13,580
45,60
(VDC)
7.0
8.4
16.8
33.6
67.2
84
(VDC)
0.5
0.6
1.2
2.4
4.8
6
005
006
012
024
048
060
110
1.06
154
11
2 coils in parallel (Connect relay coil terminal No.1 to No.3 and No.2 to No.4)
Coil code
Rated Coil Voltage
Coil Resistance +/-10%
Must Operate Voltage
*
Must Release Voltage
*
Rated Power (W)
(±10%)
(VDC)
5
6
12
24
48
60
110
(Ω)
23.5
34
135
550
2,200
3,395
11,400
(VDC)
3.5
4.2
8.4
16.8
33.6
42.0
77.0
(VDC)
0.25
0.3
0.6
1.2
2.4
3
005
006
012
024
048
060
110
1.06
5.5
Note 1: All values in the tables are valid for 20°C and zero contact current.
Note 2: Nominal voltage is different from indication of part number
Note 3: Please use at rated coil voltage. Please refer to characteristic data and set up adequate voltage in case of use at over voltage.
* Specified operate values are valid for pulse wave voltage.
■
Safety Standards
Type
UL
Compliance
UL 508
File No. E63615
Contact rating
10A, 450VDC, resistive, 10,000 cycles
for series connection of each NO contact.
10A, 400VDC, resistive, 10,000 cycles
for series connection of each NO contact.
10A, 200VDC, resistive, 10,000 cycles for each NO contact.
VDE
IEC/EN61810-1
10A, 400VDC, resistive, 10,000 cycles
for series connection of each NO contact.
10A, 200VDC, resistive, 10,000 cycles for each NO contact
4
FTR-J2 Series
■
Characteristic Data (Reference)
* Characteristic data is not a guaranteed value, but measured values of samples from production line.
Coil temperature rise
Operating range
(contacts connected in series)
(contacts connected in series)
70
60
50
40
2.0
0A
1.8
1.6
1.4
1.2
1.0
0.8
0.6
10A
10A
30
20
Operate voltage (hot coil)
Operate voltage (cool coil)
0A
10
0
0
0.2 0.4 0.6
1.4
0.8
1
1.2
1.6
0
10 20 30 40 50
60
70 80
90
100
Coil power (W)
Ambient temperature (°C)
Note: When each contact is used independently, above
graph shall be read; same voltage is applied on 2 coils,
coil power is sum of 2 coils, applied current 10A is 10A
apply on each contact set.
Note: When each contact is used independently, above
graph shall be read; same voltage is applied on 2 coils,
applied current 10A is 10A apply on each contact set.
Life curve
Life curve
(contacts connected in series in the same load)
(Each contact is used independently)
60
60
50
50
450VDC
40
200VDC
40
resistive
resistive
30
30
20
10
0
20
10
0
0
2
4
6
8
10
12
0
2
4
6
8
10
12
Contact current load (A)
Contact current load (A)
5
FTR-J2 Series
■
Dimensions
•
Dimensions
24
+0.3
23
+0.3
.
8- pre solder
1
1
0.35
0.4
φ
0.5
7.5
5
(1.8)
3.5
16.5
7.5
* Dimensions of the terminals do not include thickness of pre-solder.
•
Schematics
(BOTTOM VIEW)
4
8+
Relay contact terminals have polarity.
Please connect higher potential side of the load to (+).
Please always use a varistor to protect the coil from back
electromotive force.
Use of other protection element may shorten relay life exces-
sively. Varistor must connect in parallel to the relay coil.
Please refer to Recommended Circuit.
7
3
2
6
5+
1
•
PC Board Mounting Hole Layout
(BOTTOM VIEW)
16.5
±0.1
3.5
±0.1
4-
φ
0.9
±0.1
4-
φ
1.3
±0.1
(1.8)
3.5
±0.1
16.5
±0.1
(24)
( ):
Reference value
Unit: mm
* Tolerance of PC board mounting hole layout : ±0.1 unless otherwise specified.
6
FTR-J2 Series
■
Circuit
■ Recommended Circuit (2 contacts connected in series under the same common load)
●
Load circuit and input circuit (coil sides) for 10A 450VDC
●
Load circuit and input circuit (coil sides) for 10A 450VDC
(2 coils connect in parallel)
(2 coils connect in series)
Surge protection
device (Varistor)
Surge protection
device (Varistor)
Connect on PC board
Current: 10A
Connect on PC board
Current: 10A
(+)
8
4
3
2
4
8
6
(+)
7
7
3
2
Nominal
coil voltage
Power
supply
450VDC
Power
supply
450VDC
Nominal
coil voltage
Load
circuit
Load
circuit
6
5
(+)
(+)
5
1
1
Current: 10A
Current: 10A
Load circuit contact terminals has polarities (+) and (-). Coils do not have polarity.
BOTTOM VIEW
■ Recommended Circuit (each contact is used independently)
●
Load circuit and input circuit (coil sides) for 10A, 200VDC
●
Load circuit and input circuit (coil sides) for 10A, 200VDC
(dual circuit)
2 coils connect in series
(dual circuit)
Each coil is used independently
Surge protection
device (Varistor)
Surge protection
Connect on PC board
device (Varistor)
Current:10A
Current: 10A
Power
supply
200VDC
Nominal
coil voltage
Power
supply
200VDC
4
8
6
(+)
7
Load
circuit
4
8
(+)
Load
circuit
7
3
2
3
2
Nominal
coil voltage
6
(+)
5
Nominal
coil voltage
5
(+)
1
Power
supply
200VDC
1
Power
supply
200VDC
Current:10A
Current:10A
Load
circuit
Load
circuit
BOTTOM VIEW
Load circuit contact terminals has polarities (+) and (-). Coils do not have polarity.
Note 1:
In case 2 coils are connected in series, connect coil terminal #2 to #3 on PCB circuit. In case 2 coils are connected in parallel,
connect coil terminal #1 to #3 and connect coil terminal #2 to #4 on PCB. Regarding terminal number, refer to schematics data.
Please use varistor as surge protection device. If varistor will not be used, the electrical life need to be derated.
Varistor surge protection device should be connect parallel to coil(s). Suitable voltage of varistor is 3 times the coil voltage.
For max. contact life and correct functioning of the relay, positive polarity of load should be connected to pin 8 and pin 5.
If not, damage to the relay can occur.
Note 2:
Note 3:
Note 4:
Warning: At current loads at max. switching capacity 10A (200VDC) correct polarity is vital for the correct and safe functioning of the relay
!
7
FTR-J2 Series
■
WARNING
!
We highly recommend to use the circuit layouts on this datasheet to switch 10A 450VDC or 10A 200VDC.
Polarity of the terminals shall be kept as specified, otherwise fire or electric shock may occur. There would be a
possibility that high voltage DC relay loses breaking current ability as one of failure modes. Please provide fail
safeness design on the circuit not to result in any injury or deaths or damages.
To secure safety,
the relay shall
not be used in exceeding its specifications including operation life, and handle the relay as a periodic mainte
–
nance component.
■
Caution
!
Each coil shall be synchronized completely in case 2 coils are used separately at 10A 450VDC switching. In-
complete synchronization may shorten relay life excessively.
!
!
!
!
!
!
Magnetic field is generated on the top surface of relay. Please consider its influence to other components.
When 2 or more relays are mounted quite closely,
please confirm operation before actual use.
All values mentioned in this datasheet are provided under ideal conditions. Please perform the confirmation
test before actual use.
Reflow soldering is prohibited
Do not use FTR-J2 relays for automotive applications.
Do not use relays in the atmosphere with sulfide gas, chloride gas or nitric oxide. Contact resistance may
increase.
Do not use silicon or silicon-containing product or materials near relays. It may cause contact failure.
8
FTR-J2 Series
GENERAL INFORMATION
1.
ROHS Compliance
•
All relays produced by Fujitsu Components are compliant with RoHS directive 2011/65/EU including amend-
ments.
•
Use of Cadmium in electrical contacts is exempted as per Annex III of the RoHS directive 2011/65/EU.
Please consider expiry date of exemption. Relays with Cadmium containing contacts are not to be used for
new designs.
•
All relays are lead-free. Please refer to Lead-Free Status Info for older date codes at:
•
Characteristic data is not guaranteed values, but measured values of samples from production line.
2.
Recommended lead free solder condition
•
Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has
been verified to be compatible with PbSn assembly process.
•
Recommended solder for assembly: Sn-3.0Ag-0.5Cu.
Flow Solder Condition:
Pre-Heating:
maximum 120˚C
within 90 sec.
Soldering:
dip within 5 sec. at
255˚C ± 5˚C solder bath
Relay must be cooled by air immediately
after soldering
Solder by Soldering Iron:
Soldering Iron:
30-60W
Temperature:
maximum 350-360˚C
Duration:
maximum 3 sec.
We highly recommend that you confirm your actual solder conditions
3.
Moisture Sensitivity
•
Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicat-
ed.
4.
Tin Whiskers
•
Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable
length whisker was found by our in house test.
9
FTR-J2 Series
Fujitsu Components International Headquarter Offices
Japan
Asia Pacific
Korea
FUJITSU COMPONENT LIMITED
Shinagawa Seaside Park Tower 19
F
,
12-4, Higashi-shinagawa 4-chome, Shinagawa-ku,
Tokyo,140-0002, Japan
FUJITSU COMPONENTS ASIA, LTD.
102E Pasir Panjang Road
#01-01 Citilink Warehouse Complex
Singapore 118529
FUJITSU COMPONENTS KOREA LIMITED
Alpha Tower #403, 645 Sampyeong-dong,
Bundang-gu, Seongnam-si,
Gyeonggi-do,
13524 Korea
Tel: (81-3) 3450-1682
Tel: (65) 6375-8560
Tel: (82) 31-708-7108
Fax: (81-3) 3474-2385
Fax: (65) 6273-3021
Fax: (82) 31-709-7108
Email: fcl-contact@cs.jp.fujitsu.com
Email: fcal@sg.fujitsu.com
Email: fcal@sg.fujitsu.com
North and South America
China
FUJITSU COMPONENTS AMERICA, INC
2290 North First Street, Suite 212
San Jose, CA 95131, USA
FUJITSU ELECTRONIC COMPONENTS (SHANGHAI) CO., LTD.
Unit 4306, InterContinental Center
100 Yu Tong Road, Shanghai 200070,
China
Tel: (1-408) 745-4900
Fax: (1-408) 745-4970
Tel: (86-21) 3253 0998
Email: components@us.fujitsu.com
Web: us.fujitsu.com/components
Fax: (86-21) 3253 0997
Email: fcal@sg.fujitsu.com
Europe
Hong Kong
FUJITSU COMPONENTS EUROPE B.V.
Diamantlaan 25
2132 WV Hoofddorp
FUJITSU COMPONENTS HONG KONG CO., LTD
Unit 506, Inter-Continental Plaza
No.94 Granville Road, Tsim Sha Tsui, Kowloon,
Hong Kong
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: info@fceu.fujitsu.com
Tel: (852) 2881-8495
Tex: (852) 2894-9512
Email: fcal@sg.fujitsu.com
©2018 Fujitsu Components Europe B.V.
All rights reserved. All trademarks or registered trademarks are the property of their respective owners.
The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general
information purposes.
The use of the contents, data and information provided in this datasheet is at the users’ own risk.
Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive,
complete and up to date.
Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its
employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related
graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof.
Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability
for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use,
with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness,
usefulness, availability and completeness thereof. Rev. March 16, 2018
10
