FUJITSU-FTR-K2AK024T
| Part # | FUJITSU-FTR-K2AK024T |
Download  | FUJITSU-FTR-K2AK024T |
POWER RELAY
1 POLE –
16A
Relay
FTR-K2 Series
n
FEATURES
l
SPST-NO
l
High insulation
Insulation distance: minimum 6mm between coil and
contact
Dielectric strength: 4KV
Surge strength: 10KV
l
TV-5 rating
l
Heat resistance, flammability
Class B (130° C) wire class, flammability 94V-0
l
Cadmium free contact for eco-program
l
Safety standards
UL, CSA, VDE approved
UL/CSA TV-5 rating approved
l
Flux proof sealing, RTII
l
RoHS compliant
Please see page 6 for more information
n
PARTNUMBER INFORMATION
FTR-K2
(a)
A
K
012
T
– OK
(f)
[Example]
(b) (c) (d)
(e)
(a)
Relay type
FTR-K2 :
FTR-K2-Series
(b)
Contact configuration
(c)
Coil type
A
K
: 1 form A (SPST-NO)
: Standard type (530mW)
(d) Coil
rated voltage
012 :
5…..48 VDC
Coil rating table at page 3
(e)
Contact material / TV type
(f)
Special type
T :
Silver-tin oxide / TV-5
None :
Standard (TV-5)
TH :
TV-8 rating
Actual marking does not carry the type name : “FTR”
E.g.: Ordering code: FTR-K2AK012T
Actual marking: K2AK012T
1
FTR-K2 SERIES
n
SPECIFICATION
Item
FTR-K2AK ( ) T
Contact Data
Configuration
Construction
1 form A (SPST-NO)
Single
Material
Silver tin oxide (AgSnO
2
)
Max. 100mΩ at 1A, 6VDC
250VAC / 30VDC / 16A
16A
Resistance (initial)
Contact rating
(resistive)
Max. carrying current
Max. switching voltage
Max. switching power
Min. switching load*
Mechanical
400VAC / 300VDC
4,000VA / 480W
100mA, 5VDC
Min. 2 x 10
6
operations
Min. 100 x 10
3
operations
Min. 100 x 10
3
operations
Min. 25 x 10
3
operations
530mW
Life
DC contact rating
AC contact rating
Lamp load (TV-5)
Electrical
Coil Data
Rated power (20 °C)
Operate power (20 °C)
260mW
Operating temperature range
-40 °C to +70 °C (no frost)
Max. 15ms (without bounce)
Max. 5ms (without bounce)
Min. 1,000MΩ at 500VDC
1,000VAC (50/60Hz) 1min
4,000VAC (50/60Hz) 1min
10,000V / 1.2 x 50µs standard wave
6mm
Timing Data
Operate (at nominal voltage)
Release (at nominal voltage)
Insulation
Resistance (initial)
Open contacts
Contacts to coil
Coil to contacts
Dielectric strength
Surge strength
Clearance
Creepage
6mm
EN61810-1, VDE0435
Voltage
250V
Pollution degree
Material group
Category
3
III a
B / 250V
Other
Misoperation>1us 10
to 55 to 10Hz single amplitude 0.75mm
Endurance 10
to 55 to 10Hz single amplitude 0.75mm
Misoperation>1us 200m/s²
(11 ± 1ms)
Vibration resistance
Shock
Endurance
1,000m/s² (6 ± 1ms)
Approximately 13g
Flux proof (RT II)
Weight
Sealing
* Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual
load before production since reference values may vary according to switching frequencies, environmental conditions
and expected reliability levels.
Care shall be taken on the heat generated on PC board when maximum carrying current exceeds 10A.
Please perform the confirmation test with actual conditions.
2
FTR-K2 SERIES
n
COIL RATING
Rated Coil
Voltage
(VDC)
Must Operate
Voltage
Must Release-
Voltage
Coil
Code
Coil Resistance
+/- 10% (Ohm)
Rated Power
(mW)
(VDC) *
(VDC) *
003
005
006
009
012
018
024
048
3
5
17
47
2.1
3.5
0.15
0.25
0.3
6
68
4.2
9
155
270
610
1,110
4,400
6.3
0.45
0.6
530
12
18
24
48
8.4
12.6
16.8
33.6
0.9
1.2
2.4
Note: All values in the table are valid for 20°C and zero contact current.
* Specified operate values are valid for pulse wave voltage.
Please use at rated coil voltage. Please refer to characteristic data and set up adequate voltage in case of use at over voltage.
n
SAFETY STANDARDS
Type
Compliance
UL 508
Contact rating
UL
Flammability: UL 94-V0 (plastics)
16A, 30VDC (resistive)
15A, 140VAC (resistive)
E63614
CSA
VDE
CQC
C22.2 No. 14
LR 40304
10A, 277VAC (resistive)
1/2 H
P
,
125VAC (UL), 1/3 HP 125VAC (CSA)
TV-5, 120 VAC , TV-8, 120VAC
Pilot duty: A300 (UL), C300 (CSA)
IEC/EN61810-1
EN60065 clause 14.6.1
16A, 250 VAC (cos
φ
=1)
8A, 250 VAC cos
φ
=0.4)
16A, 30 VDC (0ms)
250VAC 5/80A inrush
GB/T21711-1
GB15092-1
<FTR-K2AK( )T> 16A 250VAC
03001008195
3
FTR-K2 SERIES
n
CHARACTERISTIC DATA
(Characteristic data is not guaranteed value but measured values of samples from production line.)
4
FTR-K2 SERIES
n
DIMENSIONS
l
Dimensions
l
Schematics
l
PC board mounting
hole layout
(BOTTOM VIEW)
Unit: mm
* Dimensions of the terminals do not include thickness of pre-solder.
* Tolerance of PC board mounting hole layout : ±0.1 unless otherwise specified
Cautions
•
All values mentioned in this datasheet are provided under ideal conditions. Please perform the confirmation test
before actual use.
•
•
•
Reflow soldering is prohibited.
Do not use relays in the atmosphere with sulfide gas, chloride gas or nitric oxide. Contact resistance may increase.
Do not use silicon or silicon-containing product or materials near relays. It may cause contact failure.
5
FTR-K2 SERIES
RoHS Compliance and Lead Free Information
1. General Information
l
l
l
l
All relays produced by Fujitsu Components are compliant with RoHS directive 2011/65/EU including
amendments.
Cadmium as used in electrical contacts is exempted from the RoHS directives.
As per Annex III of directive 2011/65/EU.
All relays are lead-free. Please refer to Lead-Free Status Info for older date codes at:
Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified.
This material has been verified to be compatible with PbSn assembly process.
2. Recommended Lead Free Solder Condition
l
Recommended solder Sn-3.0Ag-0.5Cu.
Flow Solder Condition:
Pre-heating:
maximum 120˚C
within 90 sec.
Soldering:
dip within 5 sec. at
255˚C
±
5˚C solder bath
Relay must be cooled by air immediately
after soldering
Solder by Soldering Iron:
Soldering Iron
30-60W
Temperature:
maximum 350-360˚C
Duration:
maximum 3 sec.
We highly recommend that you confirm your actual solder conditions
3. Moisture Sensitivity
l
Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated.
4. Tin Whiskers
l
Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length
whisker was found by our in house test.
6
FTR-K2 SERIES
Fujitsu Components International Headquarter Offices
Japan
Asia Pacific
Korea
FUJITSU COMPONENT LIMITED
Shinagawa Seaside Park Tower 19
F
,
12-4, Higashi-shinagawa 4-chome, Shinagawa-ku,
Tokyo,140-0002, Japan
FUJITSU COMPONENTS ASIA, LTD.
102E Pasir Panjang Road
#01-01 Citilink Warehouse Complex
Singapore 118529
FUJITSU COMPONENTS KOREA LIMITED
Alpha Tower #403, 645 Sampyeong-dong,
Bundang-gu, Seongnam-si,
Gyeonggi-do,
13524 Korea
Tel: (81-3) 3450-1682
Tel: (65) 6375-8560
Tel: (82) 31-708-7108
Fax: (81-3) 3474-2385
Fax: (65) 6273-3021
Fax: (82) 31-709-7108
Email: fcl-contact@cs.jp.fujitsu.com
Email: fcal@sg.fujitsu.com
Email: fcal@sg.fujitsu.com
North and South America
China
FUJITSU COMPONENTS AMERICA, INC
2290 North First Street, Suite 212
San Jose, CA 95131, USA
FUJITSU ELECTRONIC COMPONENTS (SHANGHAI) CO., LTD.
Unit 4306, InterContinental Center
100 Yu Tong Road, Shanghai 200070,
China
Tel: (1-408) 745-4900
Fax: (1-408) 745-4970
Tel: (86-21) 3253 0998
Email: components@us.fujitsu.com
Web: us.fujitsu.com/components
Fax: (86-21) 3253 0997
Email: fcal@sg.fujitsu.com
Europe
Hong Kong
FUJITSU COMPONENTS EUROPE B.V.
Diamantlaan 25
2132 WV Hoofddorp
FUJITSU COMPONENTS HONG KONG CO., LTD
Unit 506, Inter-Continental Plaza
No.94 Granville Road, Tsim Sha Tsui, Kowloon,
Hong Kong
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: info@fceu.fujitsu.com
Tel: (852) 2881-8495
Tex: (852) 2894-9512
Email: fcal@sg.fujitsu.com
©2018 Fujitsu Components Europe B.V.
All rights reserved. All trademarks or registered trademarks are the property of their respective owners.
The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general
information purposes.
The use of the contents, data and information provided in this datasheet is at the users’ own risk.
Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive,
complete and up to date.
Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its
employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related
graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof.
Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability
for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use,
with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness,
usefulness, availability and completeness thereof. Rev. April 24
th
, 2018
7
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
