Infineon-Technologies-2ED300C17STROHSBPSA1
| Part # | Infineon-Technologies-2ED300C17STROHSBPSA1 |
Download  | Infineon-Technologies-2ED300C17STROHSBPSA1 |
Preliminary Datasheet, V4.03, August 2013
EiceDRIVER
TM
2ED300C17-S 2ED300C17-ST
Dual IGBT Driver Board for Infineon Medium
and High Power IGBT Modules
Power Management & Drives
EiceDRIVER
TM
2ED300C17-S/-ST
2ED300C17-S 2ED300C17-ST
Revision History:
Previous Version:
Version Page
2013-08
V4.03
V4.02
Subjects (major changes since last revision)
Revision history modified. All changes included.
Figure 4 and figure7 size changed.
Partial discharge test voltage added
Chapter 4.5 and 4.6 added
4.03
4.03
4.02
4.02
4.01
4.00
2
8; 18
19
Update figure 2 and figure 6
all
General review, new hardware version V6
Edition 2013-08-13
Published by
Infineon Technologies AG
59568 Warstein, Germany
© Infineon Technologies AG 2013.
All Rights Reserved.
ATTENTION PLEASE!
THE INFORMATION HEREIN IS GIVEN TO DESCRIBE CERTAIN COMPONENTS AND SHALL NOT BE
CONSIDERED AS A GUARANTEE OF CHARACTERISTICS.
TERMS OF DELIVERY AND RIGHTS TO TECHNICAL CHANGE RESERVED.
WE HEREBY DISCLAIM ANY AND ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO
WARRANTIES OF NON-INFRINGEMENT, REGARDING CIRCUITS, DESCRIPTIONS AND CHARTS
STATED HEREIN.
Information
For further information on technology, delivery terms and conditions and prices please contact your nearest
Warnings
Due to technical requirements components may contain dangerous substances. For information on the types
in question please contact your nearest Infineon Technologies Office.
Infineon Technologies Components may only be used in life-support devices or systems with the express
written approval of Infineon Technologies, if a failure of such components can reasonably be expected to
cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or
system. Life support devices or systems are intended to be implanted in the human body, or to support
and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health
of the user or other persons may be endangered.
EiceDRIVER
TM
2ED300C17-S/-ST
Safety notice
The driver may only be used for the purposes described by the manufacturer.
Inadmissible alterations and use of spare parts or accessories not recommend by Infineon
may cause fire, electric shock and injuries.
This document has to be available to all users, developers and qualified personnel working
with the driver.
If measurements and tests on the device have to be carried out during operation,
the regulations of the work on live parts are to be observed and suitable test equipment
is to be used.
Prior to installation and commissioning please read this document thoroughly.
Commissioning is prohibited if there is visible damage by inappropriate handling
or transportation.
Ensure ESD protection during handling.
Connect or disconnect only when power is turned off.
Always keep sufficient safety distance during commissioning without closed
protective housing.
Contact under live condition is strictly prohibited.
Work after turn-off is impermissible until the absence of supply voltage has been
verified.
During work after turn-off it has to be observed that components heat up during
operation. Contact can cause injuries.
Electrically and mechanically, the driver is mounted on
to customer’s
PCB by
soldering. The
mechanical strength has to be verified by the user and, if necessary,
assured with appropriate tests.
The driver is designed to be used in combination with Infineon IGBT modules,
especially IHM, EconoPACK+, PrimePACK
TM
and 62mm. In case of ulterior use,
safe operation cannot be ensured.
Exclusion clause:
The datasheet is part of the Infineon IGBT driver 2ED300C17-S/-ST. To ensure safe and reliable operation
it is necessary to read and understand this datasheet.
The Infineon IGBT driver 2ED300C17-S/-ST is only intended for control of Infineon IGBT modules.
Infineon cannot warrant against damage and/or malfunction if IGBT modules used not produced by Infineon.
In this context, Infineon retains the right to change technical data and product specifications without prior
notice to the course of improvement.
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
3
EiceDRIVER
TM
2ED300C17-S/-ST
This side is intentionally left blank.
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
4
EiceDRIVER
TM
2ED300C17-S/-ST
Dual channel high voltage IGBT driver board
Product Highlights
Galvanically isolated dual channel IGBT driver
Reinforced isolation according to EN 50178
Integrated protection features
5kV isolation test performed as 100% test
High Electromagnetic Compatibility
Features
Designed for Infineon IGBT modules up to 1700V
High peak output current of 30A
Integrated DC-DC SMPS
Soft Shut Down in fault conditions
Dynamic Over Current Detection
IGBT desaturation monitoring
Interlocking in half-bridge mode
Open drain fault output
Typical Applications
Low impedance 15V inputs for high noise immunity
±15 V secondary drive voltage
Short propagation delay time
Optional sense function
Renewable energies
Drives and automation
Transportation
Power supplies
Medical
RoHS compliant
UL94V-2 compliant materials
UPS systems
Figure 1: Basic schematic for driver setup
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
5
EiceDRIVER
TM
2ED300C17-S/-ST
Table of Contents
Page
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
6
EiceDRIVER
TM
2ED300C17-S/-ST
Block Diagram and Schematic
1
Block Diagram and Schematic
Figure 2: Block Diagram 2ED300C17-S/-ST
Figure 3: Peripheric components for half-bridge mode
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
7
EiceDRIVER
TM
2ED300C17-S/-ST
Functional Description
2
Functional Description
EiceDRIVER™
(eupec IGBT controlled efficiency DRIVER) is the name of a family of IGBT-Drivers
consisting of IGBT driver boards and IGBT driver ICs.
The 2ED300C17-S/-ST is a dual channel high voltage gate driver board featuring reinforced isolation
between logic side and high voltage output.
Control and protection functions are included to ease the design of highly reliable systems.
The 2ED300C17-S is designed for use in industrial applications and the 2ED300C17-ST, with special
coating, for the use in more demanding applications like railway traction or windmills.
The device consists of two galvanically separated driver channels and features two operating functions, the
direct mode and the half-bridge mode, to drive IGBT modules.
The 2ED300C17-S/-ST is designed for use with Infineon IGBT modules up to 1700V in applications with high
safety and reliability requirements and aims for power ratings of 75kW to 1MW.
The driver also includes IGBT desaturation protection, external failure input and Undervoltage Lockout
(UVLO) detection. All fault states set the fault memory and activate the open drain fault output.
2.1
Reinforced Isolation
The most important safety feature of the 2ED300C17-S/-ST high voltage driver board is the reinforced
isolation between primary and secondary side. This is achieved by using a specially designed transformer
characterized by lowest coupling capacitances, , high isolation stability and by appropriate creepage and
clearance distances on the printed circuit board.
Figure 4
shows the specially transformer design for high
isolation solution.
The clearance and creepage distances comply with VDE0110 and VDE0160 / EN50178 and are designed
for pollution degree 3, over voltage class III. All materials used within the transformer at least meet the
requirements of UL94V-2.
Figure 4: Additionally mechanical barriers for high isolation solution
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
8
EiceDRIVER
TM
2ED300C17-S/-ST
Functional Description
2.2
Integrated SMPS
A switch mode power supply with galvanically separated outputs is integrated on the 2ED300C17-S/-ST.
It generates the required voltages for both driver channels. The secondary supplies are not protected against
external short circuit.
2.3
Undervoltage Lockout (UVLO)
Undervoltage monitoring is implemented for both secondary sides, positive and negative driver supply
voltages are monitored. The Signal and Logic side is not monitored. Undervoltage lockout functionality in
both driver channels ensures correct IGBT switching operation.
If the absolute value of one of the driver channel
’s
power supplies drops below the UVLO detection level, the
IGBT is shut down using the soft shut down functionality; gate-signals are ignored and the fault output is
activated.
2.4
Dynamic Overcurrent Detection (DOCD)
The dynamic over current detection protects the IGBT in case of a short circuit. The saturation voltage during
IGBT on-state is measured and continuously compared with a defined reference signal.
The shut down reference curve has to be adapted to each individual IGBT connecting an external RC
network. If no measures are taken, the reference level for desaturation detection is approx. at 10 V. Adding
an RC network allows to tune the characteristics of the detection circuit.
2.5
Soft Shut Down (SSD)
Soft shut down is a technique to limit the current slope di/dt during turn-off. It is activated if the fault memory
is set as a consequence of a detected fault condition. A sense terminal can optionally be used to connect an
additional external resistor. This is done to adjusting the IGBT turn-off characteristics. This terminal can
optionally be used as an input for the active clamping or di/dt and dv/dt control.
2.6
External Detected Failure Analysis (EDFA)
Additional function, customizable according to individual applications such as thermo switches on heat sinks.
Digital high level on these terminals set the fault memory. Soft shut down is initiated and further operation
inhibited.
2.7
Reset
Resetting the driver can be done by applying a digital high level to the Reset-pin or by applying a digital low
level to both gate-signal inputs for at least 60ms.On Reset, the fault memory is deleted and restarting driver
operation is possible.
2.8
Control Inputs and Outputs 2ED300C17-S /-ST
Inputs of the Signal and Logic side require 15V CMOS levels according to 40xx CMOS technology. This
offers a high signal to noise ratio. In very harsh environments, negative low level input signals can be used
with the limits given for the maximum ratings.
The open drain fault output is a very low impedance output. Voltage levels similar to Signal and Logic ground
are achieved.
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
9
EiceDRIVER
TM
2ED300C17-S/-ST
Pin Configuration and Functionality
3
Pin Configuration and Functionality
Pin Label
Function
1
2
VDDS
Signal and logic supply voltage primary side
3
4
5
6
7
/Fault
Reset
CA
Open drain fault output
Active high signal and logic reset input
External capacitor terminal for half-bridge mode dead time adjustment channel A
Active high PWM input channel B
INB
8
9
CB
External capacitor terminal for half-bridge mode dead time adjustment channel B
Operating mode selection input
Open drain fault output
Mode
/Fault
INA
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Active high PWM input channel A
GNDS
Signal and logic common ground primary side
VDDP
DC/DC-SMPS supply voltage primary side
GNDP
E.B
DC/DC-SMPS ground primary side
Active high external digital fault input driver channel B
VCEsatB IGBT
desaturation sensing input driver channel B
RCB
SenseB
VB-
Desaturation reference curve RC network terminal driver channel B
Active clamping input or soft shut down resistor terminal driver channel B
External capacitor terminal for negative power supply driver channel B
External capacitor terminal for positive power supply driver channel B
VB+
COMB
GateB
Common ground terminal driver channel B
IGBT gate output driver channel B
Pin not existing; cut out
Pin not existing; cut out
Active high external digital fault input driver channel A
E.A
VCEsatA IGBT
desaturation sensing input driver channel A
RCA
SenseA
VA-
Desaturation reference curve RC network terminal driver channel A
Active clamping input or soft shut down resistor terminal driver channel A
External capacitor terminal for negative power supply driver channel A
External capacitor terminal for positive power supply driver channel A
VA+
COMA
GateA
Common ground terminal driver channel A
IGBT gate output driver channel A
Table 1 : Pin Configuration of 2ED300C17-S/-ST
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
10
EiceDRIVER
TM
2ED300C17-S/-ST
Pin Configuration and Functionality
Figure 5 :
EiceDRIVER™ pinning top view
3.1
Pin functionalities, Primary side
All input pins are compatible to 15V CMOS logic according to 40xx technology.
VDDS
15V supply voltage for signal and logic part on the primary side. All pins have to be connected.
/Fault
Open drain fault output for signalization of internal and external faults. Reset signal required to delete the
fault memory and for restarting operation after fault state.
External pull-up resistor needed.
Reset
Active high signal to delete the fault memory.
INA
Active high signal for PWM, channel A. Negative input voltage for low level is allowed within the limits given
for maximum values.
INB
Active high signal for PWM, channel B. Negative input voltage for low level is allowed within the limits given
for maximum values.
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
11
EiceDRIVER
TM
2ED300C17-S/-ST
Pin Configuration and Functionality
CA
Terminal to connect external capacitor for dead time adjustment of channel A in half-bridge mode.
CB
Terminal to connect external capacitor for dead time adjustment of channel B in half-bridge mode.
Mode
Terminal for mode selection, choosing direct mode or half-bridge mode. High level or connection to VDDS
activates half-bridge mode. Low level or connection to ground GNDS activates direct mode.
GNDS
Common ground connection for signals and supply voltage of Signal and Logic part.
All pins have to be connected.
Connection between GNDS and GNDP is permissible.
VDDP
15V supply voltage for DC/DC switch mode power supply. An external capacitor to GNDP is mandatory at
this terminal.
All pins have to be connected.
GNDP
Ground connection for DC/DC switch mode power supply.
All pins have to be connected.
Connection between GNDS and GNDP is permissible.
3.2
Pin functionalities, Secondary side
GateA
Output to IGBT gate, driver channel A. Both pins have to be connected.
COMA
Common ground connection for IGBT auxiliary emitter and all signals of driver channel A. Both pins have to
be connected.
VA+
Positive power supply, driver channel A. An external capacitor to ground COMA is mandatory at this
terminal.
VA-
Negative power supply driver channel A. An external capacitor to ground COMA is mandatory at this
terminal.
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
12
EiceDRIVER
TM
2ED300C17-S/-ST
Pin Configuration and Functionality
SenseA
Terminal for additional external soft shut down resistor or input for active clamping, di/dt or dv/dt control,
driver channel A
RCA
Desaturation reference curve RC network terminal, driver channel A
VCEsatA
IGBT desaturation sensing input, driver channel A.
E.A
Active high external digital fault input driver channel A for set fault memory.
GateB
Output to IGBT gate, driver channel B. Both pins have to be connected.
COMB
Common ground connection for IGBT auxiliary emitter and all signals of driver channel B. Both pins have to
be connected.
VB+
Positive power supply, driver channel B. An external capacitor to ground COMB is mandatory at this
terminal.
VB-
Negative power supply, driver channel B. An external capacitor to ground COMB is mandatory at this
terminal.
SenseB
Terminal for additional external soft shut down resistor or input for active clamping, di/dt or dv/dt control,
driver channel B
RCB
Desaturation reference curve RC network terminal, driver channel B.
VCEsatB
IGBT desaturation sensing input, driver channel B.
E.B
Active high external digital fault input driver channel B for set fault memory.
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
13
EiceDRIVER
TM
2ED300C17-S/-ST
Electrical Parameters
4
Electrical Parameters
Electrical parameters are differentiated into maximum values that in no case are to be exceeded and
operational conditions typical to the application. All parameters are listed in the following sections.
4.1
Absolute Maximum Ratings
Absolute maximum ratings are defined as ratings, which when being exceeded may lead
to destruction of the driver board. Unless otherwise noted all primary side parameters
refer to GNDS. The secondary side signals from driver channel A and driver channel B are measured with
respect to their individual COMA or COMB.
Parameter
Symbol
Limit Values
Unit
Remarks
min
max
1
2
3
Positive power supply voltage Logic and Signal
Positive power supply voltage DC/DC SMPS
Total input current V
VDDS
and V
VDDP
PWM signal input voltage INA, INB
Logic signal input voltage Mode, Reset
Voltage on open drain fault output
Total fault output current on one or both terminals
Peak turn on output current
V
VDDS
V
VDDP
I
VDD,sum
V
INA
, V
INB
V
Mode
, V
Reset
V
Fault
16,5
V
V
16,5
670
20
mA
V
-20
-20
20
V
20
V
I
Fault
40
mA
A
4
5
I
GateA
, I
GateB
I
GateA
, I
GateB
I
VX
30
Peak turn off output current
-30
133
8
A
DC/DC SMPS average current per output
Total DC/DC SMPS output power
Collector emitter voltage of IGBT
Minimum total gate resistor
mA
W
P
SMPS
V
CES
1700
V
R
Gmin
1
Ω
Maximum IGBT gate charge
Q
Gmax
dvce/dt
f
smax
52
50
µC
kV/µs
kHz
%
6
7
Maximum slew rate
Maximum switching frequency
60
Maximum duty cycle
d
max
100
85
Operating temperature 2ED300C17-S
Operating temperature 2ED300C17-ST
Storage temperature
T
op
-25
-40
-40
°C
°C
°C
T
op
85
T
sto
85
Table 2: Absolute maximum ratings
1
With respect to GNDS
2
With respect to GNDP
3
Calculated value for equivalent average DC input current @ maximum SMPS output power of 8W
4
Maximum output current of the transistor power stage
5
Maximum DC output current per DC/DC output voltage calculated for total SMPS power of 8W
6
The parameter is not subject to production test
–
verified by design/characterization
7
Operating temperature depends on load and environmental conditions.
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
14
EiceDRIVER
TM
2ED300C17-S/-ST
Electrical Parameters
4.2
Operating Parameters
Within the operating range the driver board operates as described in the functional description. Unless noted
otherwise, all primary side parameters refer to GNDS. The secondary side signals from driver channel A and
driver channel B are measured with respect to their individual COMA or COMB.
Parameter
Symbol
Limit Values
Unit
Remarks
min
max
Positive power supply voltage Logic and Signal
Positive power supply voltage DC/DC SMPS
PWM signal input voltage INA, INB
V
VDDS
14
16
V
V
V
V
8
V
VDDP
14
-15
-15
16
15
15
V
INA
, V
INB
V
Mode
, V
Reset
Logic signal input voltage Mode, Reset
Voltage on open drain fault output in non-fault
condition
V
Fault
16
V
9
Switching frequency
Duty cycle
f
smax
d
max
Table 3: Operating parameters
0
0
60
kHz
%
100
4.3
Recommended Operating Parameters
Unless noted otherwise, all primary side signals refer to GNDS. The secondary side signals from driver
channel A and driver channel B are measured with respect to their individual COMA or COMB.
Parameter
Symbol
Value
Unit
Remarks
Positive power supply voltage logic and signal
Positive power supply voltage DC/DC SMPS
PWM signal input voltage INA, INB
V
VDDS
15
15
15
15
V
V
V
V
10
V
VDDP
V
INA
, V
INB
V
Mode
, V
Reset
Logic signal input voltage Mode, Reset
Voltage on open drain fault output in non-fault
condition
V
Fault
15
V
11
Switching frequency @ 65°C operating temperature
f
smax
60
kHz
Table 4: Recommended operating parameters
8
With respect to GNDP
9
Operating temperature depends on load and environmental conditions.
10
With respect to GNDP
11
Operating temperature depends on load and environmental conditions.
Prepared by: RK
Preliminary data sheet
V4.03, 2013-08-13
Approved by: KS
15
EiceDRIVER
TM
2ED300C17-S/-ST
Electrical Parameters
4.4
Electrical Characteristics
The electrical characteristics involve the spread of values for the supply voltages, load and junction
temperatures given below. Typical values represent the median values, which are related to production
processes at T = 25°C. V
VDDS
and V
VDDP
are 15V. Unless otherwise noted all voltages are given with respect
to GNDS. The specification for all output driver signals is valid for driver channel A and driver channel B
without special notice. The secondary signals are measured with respect to their individual COMA or COMB.
Parameter
Symbol
Limit Values
Unit Remarks
min
typ
max
No load SMPS average DC input current
Signal and Logic DC input current
Turn on propagation delay time
Turn off propagation delay time
Transition time differences
I
VDDS
I
VDDP
t
pd,on
t
pd,off
t
dif
80
mA
mA
ns
ns
ns
ns
Ω
10
670
580
50
Minimal pulse suppression
t
md
400
3300
8
DC input impedance of INA, INB, Mode, Reset
Input threshold level
V
INA
, V
INB
V
E.A
, V
E.B
t
TD
V
Input threshold for external failure input E.A or
E.B
12
5
V
Interlock delay time half-bridge mode
1,6
50
µs
Reactivation after fault condition @ INA and INB
with low input signal
t
react
60
ms
Reference voltage for IGBT desaturation sensing
Coupling capacitance primary/secondary
10
18
15
V
C
cps
C
css
pF
pF
Coupling capacitance between secondary sides
External capacitor for Logic and Signal power
supply. Connected between VDDS and GNDS.
External capacitor for SMPS power supply.
Connected between VDDP and GNDP.
Positive supply voltage driver channel A and B
@ no switching operation
Negative supply voltage driver channel A and B
@ no switching operation
Internal capacitor on positive supply voltage
driver channel VA+ and VB+
Internal capacitor on negative supply voltage
driver channel VA- and VB-
Internal UVLO level for positive supply voltage
driver channel
Internal UVLO level for negative supply voltage
driver channel
C
VDDP
10
µF
µF
V
C
VDDS
470
V
VA+
, V
VB+
V
VA-
, V
VB-
16
-16
28
V
C
VA+,int
C
VB+,int
C
VA-,int
C
VB-,int
,
µF
µF
V
,
23
V
UVLO,pos
10,9
-9,3
V
UVLO,neg
C
CA
, C
CB
V
13
External capacitor for interlocking generation
0
1
nF
Table 5: Electrical characteristics
12
If not use E.A and E.B should be connected to COMA or COMB
13
Capacitor terminal only. Connection to another terminals or voltages not allowed.
Prepared by: RK
Preliminary data sheet
V4.03, 2013-08-13
Approved by: KS
16
EiceDRIVER
TM
2ED300C17-S/-ST
Electrical Parameters
4.5
Driver performance
The 2ED300C17-S can transmit a maximum power of 4 W per channel from primary to secondary side.
The power required to drive an IGBT is dependent of gate charge of the IGBT (datasheet value Q
G
),
switching frequency f
s
and gate voltage difference
ΔV
. The safety factor 1.2 included 20% over all
tolerances. The power for IGBT drive may be calculated by the following equation:
P
1.
2
*
Q
G
*
f
s
*
V
driver
This power is dissipated in the driver itself, in the external gate resistor and in the internal IGBT gate resistor.
The share of the total power each part has to dissipate varies with load conditions. There is a limit for the
power dissipation of each channel of the driver which significantly varies with temperature inside the cabinet
and with airflow conditions.
Figure 6
shows the usable driver output power for a typical mounting condition
with natural connection and several load conditions. Required gate power is considered to be constant.
The highest share of power dissipation inside the driver is to be expected when operating a small IGBT with
low total R
G
at high switching frequency. Whereas driving a larger IGBT with higher R
G
at low switching
frequency is less demanding regarding thermal considerations.
Figure 6: Power dissipation of the driver for different load conditions
Load 1 > load 2 > load 3 > load 4
Load 1
–
small R
G
and small C
G
Load 2
–
small R
G
and high C
G
Load 3
–
high R
G
and small C
G
Load 4
–
high R
G
and high C
G
The load is a combination of the gate resistors and the gate capacitance.
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
17
EiceDRIVER
TM
2ED300C17-S/-ST
Electrical Parameters
4.6
VCESAT reference
The short circuit detection measurement is integrated in the 2ED300C17-S. The 2ED300C17-S measures
the V
CE
voltage while the IGBT is turned on. If the V
CE
voltage rises above the preset reference voltage
during this period, a fault is triggered and the IGBT is turned off via the internal soft shut-down.
The reference curve is only adjustable via an external R
SX
and C
SX
. R
SX
sets the reference voltage and C
SX
sets the time constant for the decay to the stationary reference value.
The resistor and the capacitor are connected parallel between RC A and COM A or RC B and COM B.
Figure 7: Vce,sat reference curve
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
18
EiceDRIVER
TM
2ED300C17-S/-ST
Isolation characteristics
5
Isolation characteristics
Electrical characteristics, at Ta = 25 °C, unless otherwise specified.
Parameter
Value
Unit Remarks
Isolation test voltage
5000
V
V
V
Signal and Logic Side – Driver Channel A
and Driver Channel B (RMS, 50Hz, 1s)
Isolation test voltage
Surge voltage test
2250
9600
Driver Channel A – Driver Channel B (RMS,
50Hz, 1s)
Surge test according to EN50178 Signal
and Logic Side to Driver Channels A and B
RMS; transformer series test
According to EN 61800-5-1
Partial discharge test voltage
>1920
>15
V
Clearance and creepage distance
primary to secondary
Distance Signal and Logic Side to Driver
Channels A and B
mm
mm
mm
Clearance distance secondary to
secondary
Distance Driver Channel
Channel B. 4mm air gap included.
A
to Driver
>4,59
>14
Creepage distance secondary to
secondary
Distance Driver Channel
Channel B
A
to Driver
Table 6: Isolation characteristics
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
19
EiceDRIVER
TM
2ED300C17-S/-ST
Timing diagrams
6
Timing diagrams
Figure 8: PWM timing diagram with interlocking time functionality
Figure 9: Propagation delay times
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
20
EiceDRIVER
TM
2ED300C17-S/-ST
Mechanical dimensions
7
Mechanical dimensions
Figure 10: Package outlines top view
Figure 11: Package outlines side view
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
21
EiceDRIVER
TM
2ED300C17-S/-ST
Mechanical dimensions
Figure 12: Label
Intent of DMX Code
DMX Code
DMX Code
digit
digit quantity
Serial Number
SAP Material Number
Internal Production Order Number
Datecode (Production Year)
Datecode (Production Week)
1-5
6-11
12-19
20-21
22-23
5
6
8
2
2
Table 7: Intent of DMX code
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
22
EiceDRIVER
TM
2ED300C17-S/-ST
Handling and mounting
8
Handling and mounting
The device has been designed to be soldered onto a carrier board as a through-hole
component. Dual wave soldering process or selective soldering can be done. For more
information see IFX Additional Information, DS1, March 2008
The -ST version differentiates from the -S as it features an additional coating. The coating
used is type 1306N made by the company Peters. The soldering pins are not coated.
When further coating processes are done on the customer assembly, the compatibility of
the coated type has to be established first.
Prepared by: RK
Approved by: KS
Preliminary data sheet
V4.03, 2013-08-13
23
Published by Infineon Technologies AG
