MAGLAYERS-USA-Inc-MCM-1513M-301-RU
| Part # | MAGLAYERS-USA-Inc-MCM-1513M-301-RU |
Download  | MAGLAYERS-USA-Inc-MCM-1513M-301-RU |
Mag Layers USA, INC
Specification Sheet
P/N :
MCM-1513M-SERIES-RU
Products:
Certifications:
US Office
Contact Us
5406 Bolsa Ave.,
Huntington Beach, CA 92649
(714) 898-8377
Ⅰ
. SCOPE
：
This specification applies to the Pb Free high current type SMD Common mode filter
for MCM-1513M-SERIES
PRODUCT INDENTIFICATION
MCM – 1513M – 701
-RU
①
②
③
①
Product Code
②
Dimensions Code
③
Impedance Code
(1) SHAPES AND DIMENSIONS
mm
mm
mm
mm
mm
mm
mm
mm
A: 15.0±0.5
A1:15.0±0.6
B: 13.0±0.4
C: 6.0
Max.
D: 9.0
Typ.
E: 2.7±0.2
F: 3.8±0.2
G: 3.0±0.2
1
2
4
3
4
3
1
551
2
(2) ELECTRICAL SPECIFICATIONS
SEE TABLE 1
TEST INSTRUMENTS
Z
: HP
4291B IMPEDANCE ANALYZER
(or equivalent)
RDC : CHROMA MODEL 16502 MILLIOHMMETER
(or equivalent)
(3) CHARACTERISTICS
(3)-1 Operate temperature range ……
－
40
℃～＋
125
℃
(Including self temp. rise)
(3)-2 Storage temperature range ……
－
40
℃～＋
125
℃
MAG.LAYERS
MCM-1513M-SERIES
-RU
Page 1/7
TABLE 1
Impedance(Ω)
Rated
Current
(A) Max.
13
Insulation
Resistance
(MΩ) Min.
10
Rated
Voltage
(V)Max.
Resistance RDC(mΩ)
MAGLAYERS PT/NO.
at 100MHz
(1 line)
Min.
250
450
500
Typ.
300
550
700
MCM-1513M-301
-RU
MCM-1513M-551
-RU
MCM-1513M-701
-RU
4.7 Max.
3.8±20%
7.0 Max.
80
80
80
10
10
10
10
Rated Current
：
Based on temperature rise
(
△
T
：
40
℃
TYP.)
CIRCUIT DIAGRAM
MAG.LAYERS
MCM-1513M-SERIES
-RU
Page 2/7
(4) RELIABILITY TEST METHOD
MECHANICAL
TEST ITEM
SPECIFICATION
TEST DETAILS
Solder ability
The product shall be connected to the test
Apply cream solder to the printed circuit board .
circuit board by the fillet (the height is 0.2mm).
Refer to clause 8 for Reflow profile.
Resistance to
There shall be no damage or problems.
Temperature profile of reflow soldering
soldering
300
Soldering heat
(reflow soldering)
(Peak temperature 260
±
3
℃
10 sec)
250
200
150
100
50
30 sec Min
(230
+0
℃
)
Pre-heating
Slow cooling
(Stored at room
temperature)
150 ~ 180
℃
10
sec
.
2 min
2 min. or more
The specimen shall be passed through the reflow oven
with the condition shown in the above profile for 1 time.
The specimen shall be stored at standard atmospheric
eric conditions for 1 hour, after which the measurement
shall be made.
Terminal strength
The terminal electrode and the ferrite must
not damaged.
Solder a chip to test substrate , and then laterally apply
a load 9.8N in the arrow direction.
Strength on PC board
The terminal electrode and the ferrite must
Solder a chip to test substrate and then apply a load.
bending
not damaged.
Impedance:Within±20% of the initial value.
After the samples shall be soldered onto the test circuit
High
Insulation resistance and DC resistance on the
board,the test shall be done.
temperature
resistance
specification(refer to clause 2-1) shall be met.
The terminal electrode and the ferrite must not
damaged.
Measurement : After placing for 24 hours min.
Temperature : +125±2
℃
Applied voltage : Rated voltage
Applied current : Rated current
Testing time : 500±12 hours
MAG.LAYERS
MCM-1513M-SERIES
-RU
Page 3/7
(4) RELIABILITY TEST METHOD
MECHANICAL
TEST ITEM
SPECIFICATION
Impedance:Within±20% of the initial value.
TEST DETAILS
Humidity
After the samples shall be soldered onto the test circuit
resistance
Insulation resistance and DC resistance on the
board,the test shall be done.
specification(refer to clause 2-1) shall be met.
The terminal electrode and the ferrite must not
damaged.
Measurement : After placing for 24 hours min.
Temperature : +60±2
℃
, Humidity : 90 to 95 %RH
Applied voltage : Rated voltage
Applied current : Rated current
Testing time : 500±12 hours
Thermal shock
Impedance:Within±20% of the initial value.
Insulation resistance and DC resistance on the
specification(refer to clause 2-1) shall be met.
The terminal electrode and the ferrite must
not damaged.
1 cycle
30 min.
30 sec
+125
℃
-40
℃
30 min.
Impedance:Within±20% of the initial value.
After the samples shall be soldered onto the test
Low
Insulation resistance and DC resistance on the
circuit board,the test shall be done.
temperature
storage
specification(refer to clause 2-1) shall be met.
The terminal electrode and the ferrite must
not damaged.
Measurement : After placing for 24 hours min.
Temperature : -40±2
℃
Testing time : 500±12 hours
Vibration
Impedance:Within±20% of the initial value.
Insulation resistance and DC resistance on
the specification(refer to clause 2-1)
shall be met.
After the samples shall be soldered onto the test circuit
board,the test shall be done.
Frequency : 10 to 55 Hz
Amplitude : 1.52 mm
The terminal electrode and the ferrite must
not damaged.
Dimension and times : X ,Y and Z directions
for 2 hours each.
New solder More than 75%
Flux (rosin, isopropyl alcohol{JIS-K-1522}) shall be coated
over the whole of the sample before hard, the sample shall
then be preheated for about 2 minutes in a temperature
of 130
～
150
℃
and after it has been immersed to a depth
0.5mm below for 3±0.2 seconds fully in molten solder
M705 with a temperature of 245±2
℃
. More than 75% of the
electrode sections shall be couered
Solderability
with new solder smoothly when the sample is taken out
of the solder bath.
MAG.LAYERS
MCM-1513M-SERIES
-RU
Page 4/7
(5) LAND DIMENSION (Ref.)
PCB: GLASS EPOXY
t
＝
1.6mm
(5)-1 LAND PATTERN DIMENSIONS
(STANDARD PATTERN)
Unit:mm
(6) TEST EQUIPMENT
(6)-1 Impedance
Measured by using HP4291B RF Impedance Analyzer.
Measurement terminal
④
①
②
③
(6)-2 DC Resistance
Measured by using Chroma 16502 milliohm meter.
Measurement terminal
④
①
②
③
(6)-3 Insulation Resistance
Measured by using Chroma 19073
Measurement voltage : 50v ,Measurement time : 60 sec.
Measurement terminal
④
①
②
③
MAG.LAYERS
MCM-1513M-SERIES
-RU
Page 5/7
(6) PACKAGING
(6)-1 CARRIER TAPE DIMENSIONS (mm)
2
0
(6)-2 TAPING DIMENSIONS (mm)
Unreeling
Direction
MAG.LAYERS
MCM-1513M-SERIES
-RU
Page 6/7
450 pcs/Reel
The products are packaged so that no damage will be sustained.
Please note that the contents may change without any prior notice
due to reasons such as upgrading.
MAG.LAYERS
MCM-1513M-SERIES
-RU
Page 7/7
TYPICAL ELECTRICAL CHARACTERISTICS
Impedance VS. Frequency
MCM-1513M-301
-RU
10000
1000
100
10
Common Mode
Differential Mode
1
1
10
100
Frequency(MHz)
1000
MCM-1513M-551
-RU
10000
1000
100
10
Common mode
Differential mode
Common Mode
Differential Mode
1
1
10
100
Frequency(MHz)
1000
MAG.LAYERS
MCM-1513M-SERIES
-RU
ATTACHMENT-1
TYPICAL ELECTRICAL CHARACTERISTICS
Impedance VS. Frequency
MCM-1513M-701
-RU
10000
1000
100
10
Common Mode
Differential Mode
1
1
10
100
1000
Frequency(MHz
)
MAG.LAYERS
MCM-1513M-SERIES
-RU
ATTACHMENT-1
