MetalLions-ACW5020-152T15
| Part # | MetalLions-ACW5020-152T15 |
Download  | MetalLions-ACW5020-152T15 |
Wire Wound Type Common Mode Filter
SPECIFICATIONS
Customer
：
Customer P/N:
Drawing No
：
Quantity
：
Ser
i
es
AC
W
–
0
Pcs.
Date :
2017/09/06
Meled
P/N
：
Series/
參照
AC
W
–
SPECIFICATION
ACCEPTED BY:
COMPONENT
ENGINEER
ELECTRICAL
ENGINEER
MECHANICAL
ENGINEER
APPROVED
REJECTED
For Customer approval Only
Qualification Status:
Approved By
Full
Verified By
Restricted
Rejected
Re-checked By
Checked By
Comments:
Wire Wound Type Common Mode Filter
Version change history
Rev.
01
Effective Date
/
Changed Contents
New release
Change Reasons
/
Approved By
/
Wire Wound Type Common Mode Filter
0
– – – – –
A
CUSTOMER
CUSTOMER P/N
REV.
PRODUCT
TYPE
ACW
5020-SERIES
SP-20103001
Meled
P/N
FILE NO.
A
B
C
D
E
F
G
H
I
4.8 ±0.2
5.0 ±0.2
2.5 Max
0.8 Typ
1.0 Typ
2.3 Ref
1.6 Ref
0.8 Ref
1.0 Ref
DIMENSION
（
U
NI
T
：
mm）
1.
2
.
CIRCUIT DIAGRAM
3.
NOTE
：
ELECTRICAL CHARACTERISTIC
Common mode
4.
Rated
Voltage
(V)
DCR
(mΩ)
MAX
Rated Current
IR
MΩ
MIN
Test
Frequency
Impedance
Meled P/N
(A)
Max.
（
）
(Ω)
MAX
100 (Typ)
250 (Typ)
420 (Typ)
500 (Typ)
1000 (Typ)
1400 (Typ)
1500 (Typ)
100MHz/0.5V
100MHz/0.5V
100MHz/0.5V
100MHz/0.5V
100MHz/0.5V
100MHz/0.5V
100MHz/0.5V
50
50
50
50
50
50
50
13
20
27
27
34
56
56
6.0
5.0
4.0
4.0
2.0
1.5
1.5
10
10
10
10
10
10
10
ACW
5020-101
T60
ACW
5020-251
T50
ACW
5020-421
T40
ACW
5020-501
T40
ACW
5020-102
T20
ACW
5020-142
T15
ACW
5020-152
T15
1.IDC
：
∆
T=40
℃
Typ.
2.I.R
：
50V(DC)/0.5S
Wire Wound Type Common Mode Filter
0
– – – – –
A
CUSTOMER P/N
Meled
P/N
CUSTOMER
REV.
ACW
5020-SERIES
SP-20103001
PRODUCT
FILE NO.
CHARACTERISTICS(REFERENCE)
5.
ACW
5020-251
T50
ACW
5020-501
T40
ACW
5020-102
T20
ACW
5020-152
T15
Wire Wound Type Common Mode Filter
0
– – – – –
A
CUSTOMER
CUSTOMER P/N
REV.
ACW
5020-SERIES
SP-20103001
PRODUCT
Meled
P/N
FILE NO.
CHARACTERISTICS(REFERENCE)
5.
ACW
5020-421
T40
Wire Wound Type Common Mode Filter
0
– – – – –
A
CUSTOMER
CUSTOMER P/N
Meled
P/N
REV.
ACW
5020-SERIES
SP-20103001
PRODUCT
FILE NO.
MATERIAL LIST
6.
NO.
ITEM
CORE
DESCRIPTION
SUPPLIER
1
2
3
4
FERRITE
FENGYIN OR EQ
WIRE
P180 Grd1
43*2*16.5
EPOXY RESIN
ELEKTRISOLA OR
EQ
NAGASE OR
EQ
ADHESIVE
SOLDER
Sn99.3:Cu0.7
SHENMAO OR
EQ
8
7.
TAPING SPECFICATIONS
Reel Dimensions
（
Unit: mm)
Quantity
A
B
C
D
Pcs/Reel
2500
330
100
13
12.5
Wire Wound Type Common Mode Filter
0
– – – – –
A
CUSTOMER
CUSTOMER P/N
REV.
ACW
5020-SERIES
SP-20103001
PRODUCT
Meled
P/N
FILE NO.
RELIABILITY TESTING
8.
Operating Temperature
Appearance Inspection
Terminal Strength
– 40 to +125
℃
( Contain Heating coil )
No external defects by visual inspection
After soldering , between copper plaet and terminals
of coils , push in two directions of X , Y with
standing 10N(1.02kg) for10+/-2 sec.
Terminal should not peel off. (
Refer to figure at right )
Refer to
figure
Heat endurance of reflow
soldering
Insulating resistance
Dielectric Strength
Over 100 MΩ at 100V D.C . between wire and core
Apply at
0.5KV 3mA
for 1 minute between wire and core
Inductance coefficient ( 0~2,000 ) × 10 /
℃
( – 40~ + 125
℃
)
Inductance deviation within ± 10% , after 96 hours in 90~95%
Temperature characteristics
Humidity characteristics
relative humidity at 40 ± 2
℃
and 1 hours drying under normal condition
A test is made under the above mentioned condition , and it is kept for 2 hours in the normal
IR Reflow profile
Temperature ℃
Soldering
255 ℃
300
250
200
preheating
150
Natural cooling
100
50
Time
10sec
more than 2 min
1 to 4 min
Temperature and humidity . After that , no mechanical and electrical defect should
be found .
