Microchip-Tech-JAN2N6990
| Part # | Microchip-Tech-JAN2N6990 |
Download  | Microchip-Tech-JAN2N6990 |
TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841
1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803
Gort Road Business Park, Ennis, Co. Clare, Ireland.
Tel: +353
(0) 65 6840044
Fax: +353 (0) 65 6822298
MULTIPLE (QUAD) NPN SILICON DUAL IN-LINE
AND FLATPACK SWITCHING TRANSISTOR
Qualified per MIL-PRF-19500/559
DEVICES
LEVELS
JAN
JANTX
JANTXV
JANS
2N6989
2N6990
2N6989U
ABSOLUTE MAXIMUM RATINGS
(T
C
= +25°C unless otherwise noted)
Parameters / Test Conditions
Collector-Emitter Voltage
(3)
Symbol
V
CEO
V
CBO
V
EBO
I
C
Value
50
Unit
Vdc
Collector-Base Voltage
(3)
Emitter-Base Voltage
(3)
Collector Current
(3)
75
Vdc
6.0
Vdc
800
mAdc
TO-116 – 2N6989
2N6989
(2)
2N6989U
(2)
2N6990
(2)
1.5
1.0
1.0
Total Power Dissipation
@ T
A
= +25°C
P
D
W
Operating & Storage Junction Temperature Range
T
op
, T
stg
-65 to +200
°C
Note:
1. Maximum
voltage between transistors shall be
≥
500Vdc.
2. For
derating, see figures 6, 7, 8 and 9.
Ratings apply to total package.
3. For
thermal impedance curves, see figures 10, 11, 12 and 13.
4. Ratings
apply to each transistor in the array.
20 PIN LEADLESS
2N6989U
ELECTRICAL CHARACTERISTICS
(T
A
= +25°C, unless otherwise noted)
Parameters / Test Conditions
Symbol
Min.
Max.
Unit
OFF CHARACTERTICS
Collector-Emitter Breakdown Voltage
I
C
= 10mAdc
V
(BR)CEO
50
Vdc
Collector-Base Cutoff Current
V
CB
= 60Vdc
η
Adc
μ
Adc
μ
Adc
10
10
10
I
CBO
V
CB
= 75Vdc
V
CB
= 60Vdc, T
A
= +150°C
Emitter-Base Cutoff Current
V
EB
= 4.0Vdc
10
10
μ
Adc
η
Adc
14 PIN FLAT PACK
2N6990
I
EBO
V
EB
= 6.0Vdc
T4-LDS-0177 Rev. 1 (101229)
Page 1 of 7
TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841
1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803
Gort Road Business Park, Ennis, Co. Clare, Ireland.
Tel: +353
(0) 65 6840044
Fax: +353 (0) 65 6822298
ELECTRICAL CHARACTERISTICS
(T
A
= +25°C, unless otherwise noted)
Parameters / Test Conditions
Symbol
Min.
Max.
Unit
ON CHARACTERISTICS
(4)
Forward-Current Transfer Ratio
I
C
= 0.1mAdc, V
CE
= 10Vdc
I
C
= 1.0mAdc, V
CE
= 10Vdc
I
C
= 10mAdc, V
CE
= 10Vdc
50
75
325
300
100
100
30
h
FE
I
C
= 150mAdc, V
CE
= 10Vdc
I
C
= 500mAdc, V
CE
= 10Vdc
I
C
= 10mAdc, V
CE
= 10Vdc, T
A
= -55°C
35
Collector-Emitter Saturation Voltage
I
C
= 150mAdc, I
B
= 15mAdc
I
C
= 500mAdc, I
B
= 50mAdc
0.3
1.0
V
CE(sat)
Vdc
Vdc
Base-Emitter Saturation
Voltage
I
C
= 150mAdc, I
B
= 15mAdc
I
C
= 500mAdc, I
B
= 50mAdc
0.6
1.2
2.0
V
BE(sat)
DYNAMIC CHARACTERISTICS
Parameters / Test Conditions
Symbol
Min.
Max.
Unit
Magnitude of Small–Signal Short-Circuit Forward Current Transfer Ratio
I
C
= 20mAdc, V
CE
= 10Vdc, f = 100MHz
|h
fe
|
2.5
8.0
Forward current Transfer Ratio
h
fe
50
I
C
= 1.0mAdc, V
CE
= 10Vdc, f = 1.0kHz
Output Capacitance
C
obo
C
ibo
8.0
25
pF
pF
V
CB
= 10Vdc, I
E
= 0, 100kHz
≤
f
≤
1.0MHz
Input Capacitance
V
EB
= 0.5Vdc, I
E
= 0, 100kHz
≤
f
≤
1.0MHz
SWITCHING CHARACTERISTICS
Parameters / Test Conditions
Turn-On Time
Symbol
Min.
Max.
Unit
η
s
t
on
35
SEE FIGURE 14 / MIL-PRF-19500/559
Turn-Off Time
300
t
off
η
s
SEE FIGURE 15 / MIL-PRF-19500/559
(4) Pulse Test: Pulse Width = 300
μ
s, Duty Cycle
≤
2.0%.
T4-LDS-0177 Rev. 1 (101229)
Page 2 of 7
TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841
1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803
Gort Road Business Park, Ennis, Co. Clare, Ireland.
Tel: +353
(0) 65 6840044
Fax: +353 (0) 65 6822298
PACKAGE DIMENSIONS
T4-LDS-0177 Rev. 1 (101229)
Page 3 of 7
TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841
1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803
Gort Road Business Park, Ennis, Co. Clare, Ireland.
Tel: +353
(0) 65 6840044
Fax: +353 (0) 65 6822298
Dimensions
Dimensions
Symbol
Inches
Millimeters
Notes
Symbol
Inches
Min Max
.100 BSC
Millimeters
Notes
7, 11
Min
Max
.200
Min
Max
5.08
0.58
1.78
0.38
19.94
7.87
8.13
Min
Max
BH
LW
LW
1
LT
LS
LL
LL
1
LO
LO
1
LO
2
α
2.54 BSC
.014
.030
.008
.023 0.36
.070 0.76
.015 0.20
.785
10
4, 10
10
6
.125
.200
3.18
3.81
0.13
5.08
.150
.005
8
8
5
BL
.098
.060
15°
2.49
1.52
15°
BW
BW
1
.220
.290
.310 5.59
.320 7.37
6
.015
0°
0.38
0°
9
NOTES:
1
2
3
Dimension are in inches.
Millimeters are given for general information only.
Index area: A notch or pin one identification mark shall be located adjacent to pin one and shall be located within the shaded
area shown.
The manufacturer’s identification shall not be used as a pin one identification mark.
The minimum limit for dimension LW
1
may be .023 inch (0.58 mm) for leads number 1, 7, 8 and 14 only.
Dimension LO
2
shall be measured from the seating plane to the base plane.
This dimension allows for off-center lid, meniscus, and glass overrun.
The basic pin spacing is .100 inch (2.54 mm) between centerlines.
Each pin centerline shall be located within ±.010 inch (0.25
mm) of its exact longitudinal position relative to pins 1 and 14.
4
5
6
7
8
9
Applies to all four corners (leads number 1, 7, 8 and 14).
Lead center when
α
is 0 degrees.
BW
1
shall be measured at the centerline of the leads.
10 All
leads.
11 Twelve
spaces.
12 No
organic or polymeric materials shall be molded to the bottom of the package to cover the leads.
13 In
accordance with ASME Y14.5M, diameters are equivalent to
φ
x symbology.
FIGURE 1.
Physical Dimension and Configuration for type 2N6989
T4-LDS-0177 Rev. 1 (101229)
Page 4 of 7
TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841
1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803
Gort Road Business Park, Ennis, Co. Clare, Ireland.
Tel: +353
(0) 65 6840044
Fax: +353 (0) 65 6822298
PACKAGE DIMENSIONS
Dimensions
Inches Millimeters
Min Max
Dimensions
Symbol
Inches
Min Max
Millimeters
Notes
Symbol
Notes
Min
Max
2.92
0.48
0.38
7.11
6.60
7.37
Min
0.76
Max
CH
LW
TL
.030
.010
.008
.115 0.76
.019 0.25
.015 0.20
.280
BW
3
LS
.030
7
12
5
.050 BSC
1.27 BSC
0.076 0.152
6, 8
7
LT
LL
LD
2
LO
LO
3
α
.003
.250
.005
.005
.004
30°
.006
.370
.040
BL
6.35
0.13
0.13
9.40
1.02
BW
LU
.240
.125
.260 6.10
.290
4
9, 10
13
5
BW
2
3.18
90°
30°
90°
14
T4-LDS-0177 Rev. 1 (101229)
Page 5 of 7
TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841
1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803
Gort Road Business Park, Ennis, Co. Clare, Ireland.
Tel: +353
(0) 65 6840044
Fax: +353 (0) 65 6822298
NOTES:
1
2
3
Dimension are in inches.
Millimeters are given for general information only.
Index area: A notch or pin one identification mark shall be located adjacent to pin one and shall be located within the shaded
area shown.
The manufacturer’s identification shall not be used as a pin one identification mark.
Alternatively, a tab (dine TL)
may be used to identify pin one.
4
5
6
Dimension LD
2
shall be measured at the point of exit of the lead from the body.
This dimension allows for off-center lid, meniscus, and glass overrun.
The basic pin spacing is .050 inch (1.27 mm) between centerlines.
Each pin centerline shall be located within ±.005 inch (0.13
mm) of its exact longitudinal position relative to pins 1 and 14.
7
8
9
All leads: Increase maximum limit by .003 inch (0.08 mm) measured at the center of the flat when the lead finish is solder.
Twelve spaces.
Applies to all four corners (leads number 2, 6, 9 and 13).
10
Dimension LO may be .000 inch (0.00 mm if leads number 2, 6, 9, and 13) bend toward the cavity of the package within one
lead width from the point of entry of the lead into the body or if the leads are brazed to the metalized ceramic body.
11 No
organic or polymeric materials shall be molded to the bottom of the package to cover the leads.
12 Optional,
see note 1.
If a pin one identification mark is used in addition to this tab, the minimum limit of dimension TL does
not apply.
13 Applies
to leads number 1, 7, 8, and 14.
14 Lead
configuration is optional within dimension BW except dimensions LW and LT apply.
15 In
accordance with ASME Y14.5M, diameters are eqivalent to
φ
x symbology.
16 Pins
1, 7, 8, and 14 are collectors.
17 Pin
2, 6, 9, and 13 are bases.
18 Pin
3, 5, 10, and 12 are emitters.
19 Pins
4 and 11 are no contacts.
FIGURE 2.
Physical dimensions for type 2N6990
FIGURE 3. Schematic and terminal connections for types 2N6989 & 2N6990
T4-LDS-0177 Rev. 1 (101229)
Page 6 of 7
TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841
1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803
Gort Road Business Park, Ennis, Co. Clare, Ireland.
Tel: +353
(0) 65 6840044
Fax: +353 (0) 65 6822298
PACKAGE DIMENSIONS
NOTES:
Dimensions
Symbol
Inches
Millimeters
Min
1 Dimensions
are in inches.
Min
.073
.063
.345
.195
Max
Max
2.16
1.91
9.02
5.21
2 Millimeters
are given for general information only.
3 Unless
otherwise specified, tolerance is ±.005 inch (0.13 mm).
4 In
accordance with ASME Y14.5M, diameters are equivalent to
φ
x symbology.
A
A
1
D
.085
.075
.355
.205
1.85
1.60
8.76
4.95
D
1
D
2
D
3
E
.050 TYP
.070 .080
1.27 TYP
1.78
2.03
.025 REF
0.64 REF
1.27 REF
for pins 2 through 20
.050 REF
for pins 2 through 20
L
1
L
2
.080
.090
2.03
2.29
FIGURE 4.
Physical demension for type 2N6989U
T4-LDS-0177 Rev. 1 (101229)
Page 7 of 7
