Mini-Circuits-PHA-202-
| Part # | Mini-Circuits-PHA-202- |
Download  | Mini-Circuits-PHA-202- |
U
L
T
RA HIGH DYNAMIC RANGE
PHA-202+
Monolithic Amplifier
50Ω 0.03
to 2
.
7
G
Hz
THE BIG DEAL
y
Ultra High IP3, +46.1 dBm
y
Broadband High Dynamic Range without external Matching Components
y
Medium power, 1W
y
Excellent return loss over 15 dB
Generic photo used for illustration purposes only
y
High IP3, 46.1 dBm typ. at 1 GHz
CASE STYLE: DL1636
y
Gain,
1
7.0 dB typ. at 1 GHz
y
High Pout, P1dB 30.4 dBm typ. at 1 GHz
y
No external matching components required
+RoHS Compliant
The +Suffix identifies RoHS Compliance. See our web site
for RoHS Compliance methodologies and qualifications
APPLIC
A
T
IONS
y
Base station infrastructure
y
C
A
T
V
y
L
T
E
PRODUCT OVERVIEW
The PHA-202+ (RoHS compliant) is a medium power amplifier fabricated using E-PHEMT technology and offers extremely high
dynamic range over a broad frequency range and with low noise figure. In addition, the PHA-202+ has good input and output
return loss over a broad frequency range without the need for external matching components and has demonstrated excellent
reliability. It has repeatable performance from lot to lot and is enclosed in a 5mm x 6mm, 8 lead package for very good thermal
performance.
KEY FE
A
T
URES
Feature
Advantages
Broadband covering primary wireless communications bands:
Broad Band: 0.03 to 2.7 GHz
Cellular, PCS, LTE
The PHA-202+ matches industry leading IP3 performance relative to device size and power consumption.
The combi-
nation of the design and E-PHEMT Structure provides enhanced linearity over a broad frequency range as evidence in
the IP3 being typically 14-23 dB above the P1dB point.
This feature makes this amplifier ideal for use in:
Extremely High IP3
Versus DC power Consumption
46 dBm typical at 1.0 GHz
y
y
y
Driver amplifiers for complex waveform up converter paths
Drivers in linearized transmit systems
Secondary amplifiers in ultra High Dynamic range receivers
No External Matching Components
Required
Unlike competing products, Mini-Circuits PHA-202+ provides Input and Output Return Loss of over 15 dB up to 2 GHz
without the need for any external matching components
RE
V
. A
ECO-010399
PHA-202+
RS/G
Y
/
CP
211103
PAGE 1 OF 5
U
L
T
RA HIGH DYNAMIC RANGE
PHA-202+
Monolithic Amplifier
ELECTRICAL SPECIFICATIONS AT 25°C, 50 OHMS, UNLESS NOTED
Vd=11V
1
Vd=11V
2
Units
Condition
(MHz)
Parameter
Min.
0.03
—
Typ.
Max.
2.7
—
Typ.
Frequency range
Gain
0.03-2.7
18.3
17.7
16.8
14.3
12.1
20.5
25.5
28.6
17.7
12.0
15.5
15.2
15.7
19.1
9.4
GHz
30
18.3
17.9
17.0
14.7
12.7
21.2
21.7
19.5
20.3
14.9
15.1
16.4
19.4
22.5
9.8
500
—
—
1000
2000
2700
30
—
—
dB
13.2
—
16.1
—
500
Input return loss
1000
2000
2700
30
dB
500
Output return loss
1000
2000
2700
2000
30
dB
dB
Reverse isolation
23
23.3
29.2
29.8
29.8
27.0
25.2
50.3
48.8
46.2
41.7
38.8
3.0
28.4
30.2
30.4
28.1
25.7
51.0
48.5
46.1
43.2
39.4
3.2
500
Output power @1dB compression
1000
2000
2700
30
dBm
500
Output IP3
3
Noise figure
1000
2000
2700
30
dBm
500
3.3
3.0
1000
2000
2700
3.5
3.3
dB
4.4
4.3
5.4
5.2
Device operating voltage
11
11
V
Device operating current
—
350
416
335
mA
Device current variation vs. temperature
4
Device current variation vs voltage
5
Thermal Resistance, junction-to-ground lead at 85°C stage temp.
188.6
0.0485
16.1
188.6
0.0485
16.1
µA/°C
mA/mV
°C/W
1. Measured on Mini-Circuits Characterization test board MB018. See Characterization
T
e
st Circuit (Fig. 1)
2. Measured on Mini-Circuits Application test board TB-962+. See Characterization
T
e
st Circuit (Fig. 2)
3.
T
e
sted at Pout=16dBm / tone.
4. (Current at 85°C — Current at -45°C)/130
5. (Current at 11.5V-current – Current at 10.5V)/1000
PAGE 2 OF 5
U
L
T
RA HIGH DYNAMIC RANGE
PHA-202+
Monolithic Amplifier
MAXIMUM R
A
T
INGS
6
Parameter
Operating Temperature
(ground lead)
Storage Temperature
Junction Temperature
Power Dissipation
Ratings
-40°C to 85°C
-65°C to 150°C
179°C
5.8W
+24 dBm (5 minutes max.)
+19 dBm (continuous)
Input Power (CW)
DC Voltage on Pin 7
14V
6. Permanent damage may occur if any of these limits are exceeded. Electrical maximum ratings are
not intended for continuous normal operation.
SIMPLIFIED SCHEM
A
T
IC AND PIN DESCRIPTION
RF-OUT
RF-IN
and DC-IN
GND
Function
Pin Number
Description
RF input
RF-IN
RF-OUT and DC-IN
GND
2
7
RF output and DC input
Ground
Paddle
1,3-6,8
NC
No connection
PAGE 3 OF 5
U
L
T
RA HIGH DYNAMIC RANGE
PHA-202+
Monolithic Amplifier
CHARACTERIZATION TEST CIRCUIT
Fig 1. Characterization Circuit
Note: This
block diagram is used for characterization. (DUT soldered on Mini-
Circuits Characterization test board MB018)
VDD
MB018
7
Gain, Return loss, Output power at 1dB compression (P1 dB), output IP3
(OIP3) and noise figure measured using Agilent’s N5242A PNA-X microwave
network analyzer.
RF-IN
2
RF-OUT
Conditions:
1. Gain and Return loss: Pin= -25dBm
1,3-6,8 &
Paddle
2. Output IP3 (OIP3):
T
wo tones, spaced 1 MHz apart, 16 dBm/tone at output.
ZX85-12G-S+
(or Internal Bias
T
e
e of PNA-X)
BLK-18+
(or DC Blok of
PNA-X)
RECOMMENDED APPLICATION CIRCUIT
Component
P/N
SUPPLIER
Value
Size
V
DD
C3
GRM-
155R71E103KA01D
C1, C2, C3
MURATA
0.01uF
0402
L1
WA8514-AE
COILCRAFT
5.6uH
1708
L1
Fig 2. Application Circuit
Note: (DUT soldered on Mini-Circuits Application test board TB-962+)
Gain, Return loss, Output power at 1dB compression (P1 dB), output IP3
(OIP3) and noise figure measured using Agilent’s N5242A PNA-X microwave
network analyzer.
C1
RF-IN
RF-OUT
2
7
DUT
C2
1,3-6,8 &
Paddle
Conditions:
1. Gain and Return loss: Pin= -25dBm
2. Output IP3 (OIP3):
T
wo tones, spaced 1 MHz apart, 16 dBm/tone at output.
PRODUCT MARKING
MCL
P202
index over pin 1
Marking may contain other features or characters for internal lot control
PAGE 4 OF 5
U
L
T
RA HIGH DYNAMIC RANGE
PHA-202+
Monolithic Amplifier
ADDITIONAL DE
T
A
ILED TECHNICAL INFORMATION IS AVAILABLE ON OUR DASH BOARD. TO ACCESS
Data Table
Performance Data
Case Style
Swept Graphs
S-Parameter (S2P Files) Data Set (.zip file)
DL1636 Plastic package, exposed paddle
lead finish: Matte Tin
F68
Tape & Reel
7” reels with 20, 50, 100, 200, 500 or 1K devices
13” reels with 2K, 3K, 4K devices
Standard quantities available on reel
Suggested Layout for PCB Design
Evaluation Board
PL-522
TB-962+
ENV08T1
Environmental Ratings
ESD R
A
T
ING
Human Body Model (HBM): Class 1B (Pass 500V) in accordance with ANSI/ESD STM 5.1 – 2001
MSL R
A
T
ING
Moisture Sensitivity: MSL1 in accordance with IPC/JEDEC J-STD-020D
MSL TEST FLOW CHART
Visual
Inspection
Electrical
T
e
st
SAM
Analysis
Start
Soak
85°C/85RH
168 hours
Reflow 3 cycles
260°C
Bake at 125°C,
24 hours
Visual
Inspection
Electrical
T
e
st
SAM
Analysis
Finish
NOTES
A. Performance
and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document.
B. Electrical
specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions.
C. The
parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard
T
e
rms”); Purchasers of this part are entitled to the rights
and benefits contained therein. For a full statement of the standard.
T
e
rms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp
PAGE 5 OF 5
