Omron-Electronics-G2RV-1SG-DC21

Part #	Omron-Electronics-G2RV-1SG-DC21
Download	Omron-Electronics-G2RV-1SG-DC21

New Product

Slim I/O Relay

G2RV-SR/G3RV-SR

Global standard size,

low profile slim I/O relay with width 6.2 mm,

slim I/O solid state relay

• Realized about 25% lower profile than conventional

products, contributing to further miniaturization of the

control panel.

• Push-In Plus technology are used to save wiring work in

comparison with conventional screw terminals.

(Wiring time is reduced by 60%* in comparison with

traditional screw terminals.)

For the recent information on models that have been certified

for safety standards, refer to your OMRON website.

• No screw loosening means maintenance-free application,

realizing high reliability

• ‘Hand-free’ structure that holds an inserted flat-blade

screwdriver to achieve easier wiring work for stranded

wires.

• Screw terminal is also stocked to meet the screw type

needs.

• Mounted relay or solid-state relay has a plug-in terminal

that is difficult to bend at the time of exchange.

According to OMRON actual measurement data from November 2015.

Refer to

Safety Precautions

on page 20.

Slim I/O Relay Types

G2RV-SR series

mounted relay: electromagnetic relay …..

rom page 2

G3RV-SR series

mounted relay: solid state relay ……………

rom page 10

Common matter

Common precaution

……………………………………………………..

rom page 20

Common accessories (order separately)…………………………..

rom page 25

Slim I/O Relay

G2RV-SR

Global standard size, low profile slim

I/O relay with width 6.2 mm

• Realized about 25% lower profile than conventional

products, contributing to further miniaturization of the

control panel.

• Realized opening and closing ability with one pole 6 A slim

shape.

• Micro load products for one pole 50 mA using Au-plated

contacts for small load switching also available.

• Since G2RV is a transparent case, confirming the state of

the contact with the naked eye is possible, and easy to

confirm abnormality on-site (installed location).

• Screw terminal is also stocked to meet the screw type

needs.

For the recent information on models that have been certified

for safety standards, refer to your OMRON website.

• Mounted relay uses plug-in terminals that are difficult to

bend when exchanging.

• G3RV-SR featuring a solid state relay similar in shape to G2RV-SR also available.

Refer to

Safety Precautions

on page 20.

Features

With latching lever

(

est switch)

Push-In Plus technology

Standard model/Micro load

Terminal x 5

• Push-in

• Screw

Short bar insertion holes

Protective cover

(Released state)

Operation

Release hole

display LED

(Socket section)

Release lever

Protective cover

(Locked condition)

Latching lever

(

est switch)

Terminal (insertion) hole

Latching lever

(

est switch)

• Circuit check operation

Confirmation, reducing the inspection effort

Mechanical

indicator

• Operation

verification

which is linked

to the contact

PAT

“Foreign matter intrusion prevention structure”

“Malfunction prevention stopper”

Transparent case

Relay contact

Easy confirmation

of the situation

Release lever

Relay easily

fixed/removed

Plug-in terminal

Peace of mind as the

terminal does not bend

when replacing

G2RV-SR

Model Number Structure

Model Number Legend

G2RV-SR

@@ @

–

@ @

(1)

(2) (3)

(4) (5) (6)

(1) Basic model name

G2RV: Slim I/O Relay

(3) Terminal (wire connection)

50: Push-In Plus Terminal

70: Screw terminal

(5) Contact structure

Blank: Standard

AP: Microloads

(2) Sub type

(6) Rated input voltage

12, 24 VDC

24, 48 VAC/VC

SR: Slim relay + integrated low profile socket

(4) Latching lever (test switch)

0: Without latching lever

1: With latching lever

100, 110, 200, 230 VAC

Ordering Information

Terminal

Latching lever

(Test switch)

Classification

(Wire connection)

Rated input voltage (V)

Model

G2RV-SR500 DC12

G2RV-SR500 DC24

G2RV-SR500 AC/DC24

G2RV-SR500 AC/DC48

G2RV-SR500 AC100

AC/DC

100

Standard

110

G2RV-SR500 AC110

200

G2RV-SR500 AC200

230

G2RV-SR500 AC230

G2RV-SR501 DC24

Push-In Plus

Yes

Terminal

AC/DC

G2RV-SR501 AC/DC24

G2RV-SR500-AP DC12

G2RV-SR500-AP DC24

G2RV-SR500-AP AC/DC24

G2RV-SR500-AP AC/DC48

G2RV-SR500-AP AC100

G2RV-SR500-AP AC110

G2RV-SR500-AP AC200

G2RV-SR500-AP AC230

G2RV-SR700 DC12

AC/DC

Microloads

100

110

200

230

G2RV-SR700 DC24

G2RV-SR700 AC/DC24

G2RV-SR700 AC/DC48

G2RV-SR700 AC100

AC/DC

100

110

200

230

Standard

G2RV-SR700 AC110

G2RV-SR700 AC200

G2RV-SR700 AC230

G2RV-SR701 DC24

Screw terminal

Yes

AC/DC

G2RV-SR701 AC/DC24

G2RV-SR700-AP DC12

G2RV-SR700-AP DC24

G2RV-SR700-AP AC/DC24

G2RV-SR700-AP AC/DC48

G2RV-SR700-AP AC100

G2RV-SR700-AP AC110

G2RV-SR700-AP AC200

G2RV-SR700-AP AC230

AC/DC

Microloads

100

110

200

230

Note:

Sockets are not sold individually.

G2RV-SR

Relay for Maintenance

Model Number Legend

G2RV-1-SI-G

G2RV-1-S(-AP)-G

G2RV-1 – S

–

– G

(1) (2)

(3) (4) (5) (6)

(1) No. of poles

1: 1 pole

(4) Contact material

Blank: Ag alloy

AP: Ag alloy + Au plating

(2) Terminal

S: plug-in

(5) Types of relay for exchange

G: G2RV-SR series equipped

Relay

(3) Latching lever (Test switch)

Blank: Without latching lever

I: With latching lever

(6) Rated coil voltage

Number: 11, 21, 48 VDC

List of Models

Latching

Lever

(Test switch)

Rated coil

voltage (V)

Type

Model

Applicable model

G2RV-1-S-G DC11

G2RV-1-S-G DC21

G2RV-SR700/500 DC12V

G2RV-SR700/500 DC24V

G2RV-SR700/500 AC/DC24V

G2RV-SR700/500 AC/DC48V

G2RV-SR700/500 AC100V

G2RV-SR700/500 AC110V

G2RV-SR700/500 AC200V

G2RV-SR700/500 AC230V

G2RV-SR701/501 DC24V

G2RV-SR701/501 AC/DC24V

G2RV-SR700/500-AP DC12V

G2RV-SR700/500-AP DC24V

Standard

G2RV-1-S-G DC48

Yes

G2RV-1-SI-G DC21

G2RV-1-S-AP-G DC11

G2RV-1-S-AP-G DC21

G2RV-SR700/500-AP AC/DC24V

G2RV-SR700/500-AP AC/DC48V

G2RV-SR700/500-AP AC100V

G2RV-SR700/500-AP AC110V

G2RV-SR700/500-AP AC200V

G2RV-SR700/500-AP AC230V

Microload

G2RV-1-S-AP-G DC48

Note:

Voltage is reduced within the socket for the slim I/O relay, so the rated input voltage and rated coil voltage of replacement relays are different.

Accessories (order separately)

Refer to page 25 for G2RV-SR/G3VR-SR Common Accessories.

G2RV-SR

Specifications

Ratings

Coil ratings

Must operate

voltage

Must release

voltage

Maximum

allowable voltage

Rated current

Power consumption

Rated input

voltage

Percentage of the

rated voltage

Percentage of the rated voltage

AC (VA)

DC (mW)

50 Hz

60 Hz

12 VDC

–

27.9 mA

–

Approx. 300 mW

24 VDC

13.5 mA

24 VAC/VDC

48 VAC/VDC

100 VAC

110 VAC

200 VAC

230 VAC

12.5 mA

12.6 mA

Approx. 0.5 VA

Approx. 300 mW

Approx. 0.4 VA

Approx. 250 mW

5.9 mA

6.6 mA

7.3 mA

6.1 mA

6.0 mA

5.9 mA

7.6 mA

8.4 mA

5.2 mA

80% max.*

10% min.

110%

–

Approx. 0.8 VA

Approx. 1.7 VA

–

Note:

The operating characteristics are measured at ambient temperature of 23°C.

Operating voltage will be, for mounting in the upside down direction, 85% max.

(Upside down: Direction in which the mechanical indicator faces down)

Contact ratings

Item

Standard (G2RV-SR700, 500, 701, 501)

For microloads

(G2RV-SR700-AP, 500-AP) *2

Contact configuration

SPDT

Resistive load

(cos

=1)

Inductive load

(cos

=0.4, L/R=7ms)

Resistive load

(cos

=1)

Load

6 A at 250 VAC

6 A at 30 VDC

2.5 A at 250 VAC

2 A at 30 VDC

50 mA at 30 VAC

50 mA at 36 VDC

Rated load

Rated carry current

6 A

50 mA

Maximum switching voltage

Maximum switching current

440 VAC, 125 VDC

6 A

30 VAC, 36 VDC

50 mA

1,500 VA

180 W

500 VA

60 W

Maximum switching power

–

Failure rate P value

(reference value) *1

10 mA at 5 VDC

1 mA at 100 mVDC

*1.

P level:

=0.1×10

-6

/times

This value is the value in switching frequency 120 operations/min.

*2.

If the Au plating layer is destroyed, the number will be the same as the standard type.

Characteristics

Item

Contact resistance *

Operate (Set) time *

Standard (G2RV-SR700, 500, 701, 501)

100 m

max.

For microloads

(G2RV-SR700-AP, 500-AP)

20 ms max.

AC, AC/DC: 40 ms max.

DC: 20 ms max.

Release time *

Mechanical: 18,000 operations/h

Electrical: 1,800 operations/h (rated load)

Maximum operating frequency

Insulation resistance

1,000 M

min. (at 500 VDC)

Between coil and contacts: 4,000VAC 50/60 Hz 1 min

Contact between the same polarity: 1,000 VAC 50/60 Hz 1 min

Dielectric strength

Destruction: 10 to 55 to 10 Hz, single amplitude 0.50 mm (double amplitude 1.0 mm)

Malfunction: 10 to 55 to 10 Hz, single amplitude 0.50 mm (double amplitude 1.0 mm)

Vibration resistance

Shock resistance

Destruction: 1,000 m/s

Malfunction: Energized 200m/s

, Non-energized 100m/s

Mechanical

5,000,000 operations min.

Endurance *

NO contact: 70,000 operations min.

5,000,000 operations min.

Electrical

NC contact: 50,000 operations min.

Ambient operating temperature

Operating: –40 to +55°C (with no icing or condensation)

Ambient operating humidity

Weight

Operating: 5 to 85% RH

Approx. 30 g

Contact material

Ag alloy

Ag alloy + Au plating

Note:

Above values are initial values.

Value is at ambient temperature of 23°C.

G2RV-SR

Approved standards

UL508 (file No.E41643)

Model

Contact form

Operation coil ratings

Contact ratings

Operations

6 A at 250 VAC (Resistive load)

6 A at 30 VDC (Resistive load)

2 A at 400 VAC (Resistive load)*

12 to 48 VDC

24 to 230 VAC

G2RV-SR series

SPDT

6,000

* If

the load voltage exceeds 250 VAC, please attach with a spacing

of 12 mm min., or use a separate plate (XW5Z-EP12).

12 mm 12 mm 12 mm

TÜV (EN 61810-1)

Model

Contact form

SPDT

Operation coil ratings

12, 24 VDC

Contact ratings

Operations

6 A at 250 VAC (Resistive load)

50,000

6 A at 30 VDC (Resistive load)

50,000

G2RV-SR series

24, 48 VAC/VDC

100, 110, 200, 230 VAC

2 A at 400 VAC (Resistive load)*

6,000

* If

the load voltage exceeds 250 VAC, please attach with a spacing

of 12 mm min., or use a separate plate (XW5Z-EP12).

12 mm 12 mm 12 mm

Lloyd’s (File No.07/10020)

Model

Contact form

Operation coil ratings

Contact ratings

6 A at 250 VAC (Resistive load)

2.5 A at 250 VAC (PF0.4)

6 A at 30 VAC (Ress)

12, 24 VDC

24, 48 VAC/VDC

100, 110, 200, 230 VAC

G2RV-SR500

G2RV-SR700

SPDT

2 A at 30 VDC (L/R=7ms)

6 A at 250 VAC (Resistive load)

2.5 A at 250 VAC (PF0.4)

6 A at 30 VAC (Ress)

G2RV-SR501

G2RV-SR701

12, 24 VDC

24 VAC/VDC

SPDT

2 A at 30 VDC (L/R=7ms)

12, 24 VDC

24, 48 VAC/VDC

100, 110, 200, 230 VAC

G2RV-SR500-AP

G2RV-SR700-AP

0.05 A at 30 VAC (Resistive load)

0.05 A at 36 VDC (Resistive load)

Engineering Data

Endurance curve (N.O. side)

Switching capacity of DC resistive load

10.0

1000

30 VDC resistive load

250 VAC resistive load

1.0

100

30 VDC

inductive load

250 VAC

inductive

load

0.1

100

140

180

220

Opening and closing current (A)

DC switching voltage (V)

G2RV-SR

Dimensions

(unit: mm)

Slim I/O Relay + socket

Push-In Plus Terminal Block

Models without latching lever (without test switch)

G2RV-SR500

Terminal Arrangement/Internal Connection Diagram

(TOP VIEW)

12 VDC

78 max.

G2RV-SR500-AP

(+)

Input circuit

G2RV

(–)

3.4

74.5

74.1

Other voltage

35.25

18.78

Input circuit

(5.05)

G2RV

78.77

35.3

90 max.

24 VDC

(+)

Input circuit

(–)

G2RV

: Diode bridge

(5.05)

: Light emitting diode

18.78

35.25

51.72

59.71

6.2 max.

Models with latching lever (with test switch)

G2RV-SR501

Terminal Arrangement/Internal Connection Diagram

(TOP VIEW)

12 VDC

81 max.

(+)

Input circuit

(–)

G2RV

3.4

77.5

74.1

Other voltage

Input circuit

35.25

18.78

(5.05)

G2RV

78.77

24 VDC

35.3

90 max.

(+)

Input circuit

(–)

G2RV

: Diode bridge

(5.05)

: Light emitting diode

18.78

35.25

51.72

59.71

6.2 max.

G2RV-SR

Screw terminal

Models without latching lever (without test switch)

G2RV-SR700

Terminal Arrangement/Internal Connection Diagram

(TOP VIEW)

G2RV-SR700-AP

12 VDC

Input circuit

(+)

78 max.

(–)

G2RV

3.4

74.5

74.1

Other voltage

35.18

18.71

Input circuit

(5.05)

G2RV

78.77

35.3

90 max.

24 VDC

(+)

Input circuit

(–)

G2RV

: Diode bridge

(5.05)

18.71

35.18

51.65

56.2

: Light emitting diode

6.2 max.

Models with latching lever (with test switch)

G2RV-SR701

Terminal Arrangement/Internal Connection Diagram

(TOP VIEW)

12 VDC

(+)

Input circuit

81 max.

(–)

G2RV

3.4

77.5

74.1

Other voltage

Input circuit

35.18

18.71

(5.05)

G2RV

78.77

24 VDC

35.3

90 max.

(+)

Input circuit

(–)

G2RV

: Diode bridge

(5.05)

18.71

35.18

51.65

56.2

: Light emitting diode

6.2 max.

G2RV-SR

Relay for maintenance

Models without latching lever

G2RV-1-S-G

G2RV-1-S-AP-G

5.2 max.

30.5 max.

Terminal Arrangement/

Internal Connection Diagram

(TOP VIEW)

33 max.

(Input circuit)

16.2

A1 A2

14 11

1.8

0.5

2.4

3.5

5.04

Models with latching lever (test switch)

G2RV-1-SI-G

5.2 max.

30.5 max.

Terminal Arrangement/

Internal Connection Diagram

(TOP VIEW)

(Input circuit)

36 max.

A1 A2

14 11

16.2

0.5

1.8

2.4

3.5

5.04

Slim I/O Solid State Relay

G3RV-SR

Global standard size, low profile type

slim I/O solid state relay with width

6.2 mm.

• Realized about 25% lower profile than conventional products,

contributing to further miniaturization of the control panel.

• Optimal slim, high frequency, high-speed opening and closing

SSR (solid state relay).

• Realized a slim shape with a switching capacity up to

3 A (DC), and 2 A (AC).

• Because MOSFET is used for the outlet element for the DC

load, opening and closing load of 100

A to 3 A is possible.

• Check operating status at a glance at the operating display

LED.

For the recent information on models that have been certified

for safety standards, refer to your OMRON website.

• Mounted I/O SSR (solid-state relay) uses plug-in terminals that

are difficult to bend when exchanging.

• G2RV-SR featuring a general-purpose relay similar in shape to G3RV-SR also available.

Refer to

Safety Precautions

on page 20.

Features

Push-In Plus technology

Terminal x 5

• Push-in

• Screw

Short bar insertion holes

Release hole

Operation display LED

(Socket section)

Release lever

Operation

display LED

(SSR section)

Terminal (insertion) hole

Release lever

Relay easily

fixed/removed

Plug-in terminal

Peace of mind as the terminal

does not bend when replacing

G3RV-SR

Model Number Structure

Model Number Legend

G3RV-SR

@ @ @

–

@ @

(1)

(2)

(3)

(4) (5)

(1) Basic model name

G3RV: Slim I/O Solid State Relay

(4) Output voltage specification

: AC output (triac) zero cross function available

AL :

AC output (triac) zero cross function not available

: DC output (MOS FET)

(2) Sub type

SR: Slim solid relay + integrated low profile socket

(5) Rated voltage input

12, 24 VDC

24, 48 VAC/VDC

(3) Terminal (wire connection)

500: Push-In Plus Terminal

700: Screw terminal

100, 110, 200, 230 VAC

G3RV-SR

Ordering Information

Terminal

(wire connection)

Applicable

output load

Zero cross

function

Rated input voltage

(V)

Model

G3RV-SR500-D DC12

G3RV-SR500-D DC24

G3RV-SR500-D AC/DC24

G3RV-SR500-D AC/DC48

G3RV-SR500-D AC100

G3RV-SR500-D AC110

G3RV-SR500-D AC200

G3RV-SR500-D AC230

G3RV-SR500-A DC12

G3RV-SR500-A DC24

G3RV-SR500-A AC/DC24

G3RV-SR500-A AC/DC48

G3RV-SR500-A AC100

G3RV-SR500-A AC110

G3RV-SR500-A AC200

G3RV-SR500-A AC230

G3RV-SR500-AL DC12

G3RV-SR500-AL DC24

G3RV-SR500-AL AC/DC24

G3RV-SR500-AL AC/DC48

G3RV-SR500-AL AC100

G3RV-SR500-AL AC110

G3RV-SR500-AL AC200

G3RV-SR500-AL AC230

G3RV-SR700-D DC12

G3RV-SR700-D DC24

G3RV-SR700-D AC/DC24

G3RV-SR700-D AC/DC48

G3RV-SR700-D AC100

G3RV-SR700-D AC110

G3RV-SR700-D AC200

G3RV-SR700-D AC230

G3RV-SR700-A DC12

G3RV-SR700-A DC24

G3RV-SR700-A AC/DC24

G3RV-SR700-A AC/DC48

G3RV-SR700-A AC100

G3RV-SR700-A AC110

G3RV-SR700-A AC200

G3RV-SR700-A AC230

G3RV-SR700-AL DC12

G3RV-SR700-AL DC24

G3RV-SR700-AL AC/DC24

G3RV-SR700-AL AC/DC48

G3RV-SR700-AL AC100

G3RV-SR700-AL AC110

G3RV-SR700-AL AC200

G3RV-SR700-AL AC230

AC/DC

DC load

AC load

DC load

AC load

—

Yes

—

100

110

200

230

AC/DC

Push-In Plus Terminal

100

110

200

230

AC/DC

100

110

200

230

AC/DC

100

110

200

230

AC/DC

Screw terminal

Yes

100

110

200

230

AC/DC

100

110

200

230

Note:

Sockets are not sold individually.

G3RV-SR

Solid state relay for maintenance

Model Number Legend

G3RV-

@ @

(1) (2) (3) (4)

(5)

(1) Output voltage

specification

D: DC output

(3) Terminal

S: Plug-in type

(4) Zero cross functions

2: AC output

Blank: Zero cross function available

L: Zero cross function not available

(2) Rated current

02: AC output 2 A

03: DC output 3 A

(5) Rated input voltage

Number: 12, 24, 48 VDC

List of Models

Rated

output

Load *

Rated input

voltage

(socket)

Insulation

Operation

Output Zero

cross

Model

Applicable model

method

Display

(SSR)

Function

12 VDC

G3RV-202S DC12

G3RV-202S DC24

G3RV-SR700/500-A DC12V

G3RV-SR700/500-A DC24V

24 VDC

24 VAC/VDC

48 VAC/VDC

100 VAC

110 VAC

200 VAC

230 VAC

12 VDC

G3RV-SR700/500-A AC/DC24V

G3RV-SR700/500-A AC/DC48V

G3RV-SR700/500-A AC100V

G3RV-SR700/500-A AC110V

G3RV-SR700/500-A AC200V

G3RV-SR700/500-A AC230V

G3RV-SR700/500-AL DC12V

G3RV-SR700/500-AL DC24V

G3RV-SR700/500-AL AC/DC24V

G3RV-SR700/500-AL AC/DC48V

G3RV-SR700/500-AL AC100V

G3RV-SR700/500-AL AC110V

G3RV-SR700/500-AL AC200V

G3RV-SR700/500-AL AC230V

G3RV-SR700/500-D DC12V

G3RV-SR700/500-D DC24V

G3RV-SR700/500-D AC/DC24V

G3RV-SR700/500-D AC/DC48V

G3RV-SR700/500-D AC100V

G3RV-SR700/500-D AC110V

G3RV-SR700/500-D AC200V

G3RV-SR700/500-D AC230V

Yes

G3RV-202S DC48

2 A

(at 100 to

240

Photo-

triac

G3RV-202SL DC12

G3RV-202SL DC24

VAC)

24 VDC

24 VAC/VDC

48 VAC/VDC

100 VAC

110 VAC

200 VAC

230 VAC

12 VDC

Yes

(green)

G3RV-202SL DC48

G3RV-D03SL DC12

G3RV-D03SL DC24

24 VDC

24 VAC/VDC

48 VAC/VDC

100 VAC

110 VAC

200 VAC

230 VAC

Photo-

voltage

coupler

3 A

(at 5 to

24 VDC)

–

G3RV-D03SL DC48

Different depending on the ambient temperature.

For more details, refer to

Load current vs. ambient rated temperature

on page 16.

Accessories (order separately)

Refer to page 25 for G2RV-SR/G3VR-SR Common Accessories.

G3RV-SR

Specifications

Rating (ambient temperature 25°C)

Input

G3RV-SR700/500-A series

Rated current

Input voltage

Rated input

voltage

Must operate

Must release

voltage

Percentage of the

rated voltage

voltage

50 Hz

60 Hz

12 VDC

–

15.0 mA

12.0 mA

10.8 V max.

21.6 V max.

43.2 V max.

90 V max.

24 VDC

–

24 VAC/VDC

48 VAC/VDC

100 VAC

11.3 mA

11.4 mA

11.0 mA

6.8 mA

6.2 mA

6.7 mA

7.5 mA

6.9 mA

6.2 mA

7.9 mA

8.8 mA

6.0 mA

1 V min.

±10%

–

110 VAC

99 V max.

200 VAC

180 V max.

207 V max.

230 VAC

G3RV-SR700/500-AL series

Rated current

Input voltage

Rated input

voltage

Must operate

voltage

Must release

voltage

Percentage of the

rated voltage

50 Hz

60 Hz

12 VDC

–

15.0 mA

12.0 mA

10.8 V max.

21.6 V max.

43.2 V max.

90 V max.

24 VDC

–

24 VAC/VDC

48 VAC/VDC

100 VAC

11.4 mA

11.5 mA

11.0 mA

7.7 mA

7.3 mA

7.0 mA

7.7 mA

7.3 mA

8.1 mA

8.9 mA

6.9 mA

1 V min.

±10%

–

110 VAC

99 V max.

200 VAC

180 V max.

207 V max.

230 VAC

G3RV-SR700/500-D series

Rated current

Input voltage

Rated input

voltage

Must operate

voltage

Must release

voltage

Percentage of the

rated voltage

50 Hz

60 Hz

12 VDC

–

8.0 mA

10.8 V max.

21.6 V max.

43.2 V max.

90 V max.

24 VDC

–

4.6 mA

24 VAC/VDC

48 VAC/VDC

100 VAC

5.0 mA

6.8 mA

6.2 mA

6.7 mA

7.5 mA

5.1 mA

6.9 mA

6.2 mA

7.9 mA

8.8 mA

4.3 mA

6.0 mA

1 V min.

±10%

–

110 VAC

99 V max.

200 VAC

180 V max.

207 V max.

230 VAC

Output

Item

G3RV-SR700/500-A(L)

100 to 240 VAC (50/60 Hz)

G3RV-SR700/500-D

Rated load voltage

Load voltage range

Load current

5 to 24 VDC

75 to 264 VAC (50/60 Hz)

3 to 26.4 VDC

0.1 to 2 A (Ambient temperature=25°C)

100

A to 3 A (Ambient temperature=25°C)

Inrush current resistance

30 A (60 Hz, 1 cycle)

Permissible l

t; Joule integral value

(reference value)

15A

9 A

400 W

72 W

Applied load capacity

(Output voltage: 200 VAC)

(Output voltage: 24 VDC)

G3RV-SR

Characteristics

Item

G3RV-SR700/500-A

G3RV-SR700/500-AL

3 ms max.

60 ms max.

G3RV-SR700/500-D

6 ms max.

60 ms max.

1/2 cycle of load power supply

+1 ms max.

Operate time

Release time

60 ms max.

Output ON voltage drop

Output ON resistance

Leaked current

1.6 V (RMS) max.

–

0.3

max. (at 24 VDC)

5 mA max. (at 200 VAC, 50/60 Hz)

10 µA max. (at 24 VDC)

Insulation resistance

Dielectric strength

Vibration resistance

Shock resistance

100 M

min. (at 500 VDC)

Between input and output 2,500 VAC 50/60 Hz 1 min

Malfunction: 10 to 55 to 10 Hz double amplitude 0.70 mm

300m/s

Storage: –30 to +100°C (with no icing or no condensation)

Operating: –30 to +55°C (with no icing or no condensation)

Ambient operating temperature

Ambient operating humidity

Weight

45 to 85% RH

Approx. 38 g

Pollution degree

The degree of protection by

IEC60529

IP20

Rated impulse dielectric

strength

4.0 kV/

III

Load category

LC-A

DC-12

1.5Ie 1.1Ue

5s ON, 10s OFF, 10 cycles

Overload current profile

Rated insulation voltage

240 V

Approved standards

UL 508 (file No.E64562)

Model

Input ratings

12, 24 VDC

24, 48 VAC/VDC

100, 110, 200, 230 VAC

Contact ratings

24 VDC 3 A (resistive load) at 25°C

G3RV-SR700/500-D series

G3RV-SR700/500-A(L) series

12, 24 VDC

24, 48 VAC/DC

240 VAC 2 A (resistive load) at 25°C

100, 110, 200, 230 VAC

TÜV(EN 62314)

Model

Input ratings

Contact ratings

12, 24 VDC

G3RV-SR700/500-D series

G3RV-SR700/500-A(L) series

24, 48 VAC/VDC

100, 110, 200, 230 VAC

24 VDC 3 A (resistive load)

12, 24 VDC

24, 48 VAC/VDC

100, 110, 200, 230 VAC

240 VAC 2 A (resistive load)

G3RV-SR

Engineering Data

Load current vs. ambient rated temperature

G3RV-SR700/500-A(L) series

Product mounting spacing 10 mm (Separate Mounting)

Close mounting (up to 5 units *)

0.2

−30 −20

20 25

40 55

100

20 25

40 55

100

Ambient temperature (°C)

G3RV-SR700/500-D series

Product mounting spacing 10 mm (Separate Mounting)

Close mounting (up to 5 units *)

0.5

−30 −20

20 25

40 55

100

−30 −20

20 25

40 55

100

Ambient temperature (°C)

When five or more are installed, install with 10 mm space between

each.

For details, please refer to

Mounting

on page 23.

Inrush Current Resistance: Non-repetitive

Keep the inrush current to below the inrush current resistance value (i.e., below the broken line) if it occurs repetitively.

G3RV-SR700/500-A(L) series

G3RV-SR700/500-D series

30 50

100

300 500

1,000 3,000

5,000

Energized time (ms)

30 50

100

300 500

1,000 3,000

5,000

Energized time (ms)

G3RV-SR

Dimensions

(unit: mm)

Solid state relay + socket

Push-In Plus Terminal Block

G3RV-SR500

Terminal Arrangement/

Internal Connection Diagram

(TOP VIEW)

12 VDC

Input circuit

(+)

78 max.

G3RV

(–)

A2–

INPUT

3.4

74.5

74.1

A1+

13 (+)

35.25

18.78

OUTPUT

14 (–)

(5.05)

The information in

parentheses in for

a DC

out

put.

78.77

35.3

90 max.

24 VDC

(+)

Input circuit

G3RV

(–)

A2–

INPUT

A1+

(5.05)

18.78

35.25

51.72

59.71

6.2 max.

13 (+)

OUTPUT

14 (–)

The information in

parentheses in for

a DC

out

put.

Other voltage

Input circuit

G3RV

A2–

INPUT

A1+

13 (+)

OUTPUT

14 (–)

The information in

parentheses in for

a DC

out

put.

: Diode bridge

: Light emitting diode

G3RV-SR

Screw terminal

G3RV-SR700

Terminal Arrangement/

Internal Connection Diagram

(TOP VIEW)

12 VDC

78 max.

Input circuit

(+)

3.4

74.5

74.1

G3RV

(–)

35.18

18.71

A2–

INPUT

(5.05)

A1+

13 (+)

OUTPUT

14 (–)

The information in

parentheses in for

a DC

out

put.

78.77

35.3

90 max.

24 VDC

(+)

Input circuit

(5.05)

18.71

35.18

51.65

56.2

G3RV

(–)

6.2 max.

A2–

INPUT

A1+

13 (+)

OUTPUT

14 (–)

The information in

parentheses in for

a DC

out

put.

Other voltage

Input circuit

G3RV

A2–

INPUT

A1+

13 (+)

OUTPUT

14 (–)

The information in

parentheses in for

a DC

out

put.

: Diode bridge

: Light emitting diode

G3RV-SR

Solid state relay for maintenance

Terminal Arrangement/

Internal Connection Diagram

(TOP VIEW)

G3RV-D03SL

G3RV-202S(L)

G3RV-D03SL (input circuit)

Input

30.5 max.

Load

33 max.

15.8

14 13

G3RV-202S(L) (input circuit)

Input

A1 A2

1.8

3.5

2.4

5.04

5.2 max.

Load

14 13

A1 A2

G2RV-SR/G3RV-SR

Safety Precautions

Be sure to read the

Safety Precautions for All Relays

in the website at the following URL:

http://www.ia.omron.com/.

Format of Warning Indications

WARNING

Indicates a potentially hazardous situation

which, if not avoided, will result in minor or

Ensure that the socket is not charged during wiring and

maintenance. Not doing so may result in electric shock.

moderate injury, or may result in serious

injury or death. Additionally, there may be

significant property damage.

WARNING

Do not touch the terminal section of the G2RV-SR or the

surrounding area while the power is being supplied.

Doing so may result in electric shock.

Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderate injury or in property damage.

CAUTION

Indicates supplementary comments on

what to do or avoid doing, to use the

product safety.

Precautions

for Safe Use

CAUTION

Minor electrical shock may occasionally occur.

Do not touch the G3RV terminal section (i.e., current

carrying parts) while the power is being supplied.

Includes operating precautions to ensure

that the product will operate properly and

that performance and functions will not be

adversely affected.

Precautions

for Correct

Use

The G3RV may rupture if short-circuit current flows.

As protection against accidents due to short-circuiting,

be sure to install protective devices, such as fuses and

no-fuse breakers, on the power supply side.

Meaning of Graphic Symbols for Ensuring Product Safety

Indicates the possibility of electric shock under

specific conditions.

Minor electrical shock may occasionally occur.

Do not touch the main circuit terminals on the G3RV

immediately after the power supply has been turned

OFF.

Shock may result due to the electrical charge stored

in the built-in snubber circuit.

Used for general CAUTION, WARNING, or

DANGER precautions for which there is no

specified symbol. (This symbol is also used as

the alerting symbol, but shall not be used in this

meaning on the product.)

Indicates the possibility of explosion or rupture

under specific conditions.

Note: G3RV-202S(L), G3RV-SR500/700-A(L) series

models only

Minor burns may occasionally occur.

Indicates the possibility of injuries by high

temperature under specific conditions.

Do not touch the G3RV or the heat sink while the

power is being supplied or immediately after the

power supply has been turned OFF.

The G3RV becomes extremely hot.

Provide a space of at least 3 mm between the G2RV-

SR and ground. Not doing so may result in a ground

fault.

G2RV-SR/G3RV-SR

Precautions for Safe Use

Transport

• Do

not use the product if it has been dropped on the ground.

Dropping the product may adversely affect performance.

• Do

not drop the product or subject it to abnormal vibration or shock

during transportation or mounting. Doing so may result in

deterioration of performance, malfunction, or failure.

• Do

not transport the product without it being packaged. Doing so

may result in damage, malfunction, or failure.

Usage

• Please

select the load within the rated range. Doing so may result

in damage, malfunction, or failure.

• Do

not transport the G3RV under the following conditions. Doing

so may result in damage, malfunction, or deterioration of

performance characteristics.

• Please

use the power of the rated frequency. It may cause

malfunction, failure, or risk of burnout.

<G3RV>

• High

temperature, high humidity conditions

• Install

G3RV according to instructions

Mounting

on page 23. If you

• Conditions

such as temperature change that causes rapid

condensation

install in the wrong direction, abnormal heat is generated, and may

lead to short-circuiting or burning the output element.

• G3RV

is an SSR that generates heat. Please observe the ambient

temperature setting range of G3RV. If installing in an enclosed

space, set a fan, and ventilate.

• Condition

where it is not packaged

Operating and Storage Environments

• Do

not use or store the product in the following locations. Doing so

may result in damage, malfunction, or deterioration of performance

characteristics.

• When

mounting G3RV to DIN rail, firmly fits into the groove. If it is

not properly installed, there is a risk of it falling.

• Do

not store in locations subject to ambient storage

temperatures outside the range –40 to 70°C (for G2RV) and

outside the range –30 to 100°C (for G3RV).

Wiring

•

For the current to be applied, make sure a wire size with margin is used.

Otherwise, excessive heat generated by the wires may cause burning

• Locations

subject to relative humidity outside the range 5% to

85% (for G2RV) and outside the range 45% to 85% (for G3RV).

• Locations

subject to high temperature or high humidity.

• Conditions

such as temperature change that causes rapid

condensation

• Do

not attempt to use the wire if the coat is torn. Not doing so may

result in electric shock.

• Always

turn OFF the power supply before performing wiring. Not

doing so may cause electrical shock.

<G3RV>

• L

ocations where corrosive gases or flammable gases are present

• Location

where rainwater or water droplets gets splashed

• Location

with splashes of water, oil, and chemicals, etc.

• Locations

with much dust, salt, and iron powder

• Location

with blockers

• The

wires of the socket for G3RV socket should not be passed

through the same duct as that being connected to the high-voltage

power supply. Otherwise, inductive noise may damage the G3RV

or cause it to malfunction.

• Where

static electricity or noise occurs

Push-In Plus Terminal Block

• Do

not wire anything to the release holes.

• Where

strong electromagnetic field is generated

• Where

there is a risk of exposure to radioactivity

• Do

not use or store Sockets in environments that contain silicone

gas, sulfidizing gas (e.g., SO

or H

S), or organic gas, or near

materials that contain silicone. Doing so may cause the contacts to

be unstable or to fail.

•

Do not tilt or twist a flat-blade screwdriver while it is inserted into a release

hole on the terminal block. The terminal block may be damaged

• Insert

a flat-blade screwdriver into the release holes at an angle.

The terminal block may be damaged if you insert the screwdriver

straight in.

• Do

not allow the flat-blade screwdriver to fall out while it is inserted

into a release hole.

Handling <G3RV>

• Keep

the G3RV well ventilated.

There is a risk of short-circuiting or burning due to G3RV

overheating.

•

Do not bend the wire past its natural bending radius or pull on it

with excessive force. Doing so may cause the wire disconnection.

•

Do not insert more than one wire into each terminal (insertion) hole

Mounting

• To

prevent wiring materials from smoking or ignition, confirm wire

ratings and use the wiring materials given in the following table.

• Before

you start wiring, please make sure that the socket is

securely attached to the mounting rail. If the socket is unstable, it

may come loose and risk of injury towards the workers.

Stripping length

Recommended Wire

(Ferrules not used)

•

Please insert the flat-blade screwdriver to the bottom of the hole. If

you do not insert the flat-blade screwdriver correctly, the cable will

0.5 to 1.5 mm

/AWG20 to AWG16

8 mm

Disposal

not be connected correctly

• When

disposing of the product, do not put into the fire.

• When

lubricant such as oil is attached to the tip of the driver, the

driver will fall off, with a risk of injury towards the workers.

• Do

not tilt the G2RV-SR/G3RV-SR after mounting to the support

rail. Doing so may apply excessive force to the mounting portion,

possibly damaging the product. Attach end plates (PFP-M) to

sandwich the product and hold it in place.

G2RV-SR/G3RV-SR

Precautions for Correct Use

• Do

not use or store the product in the following locations. Doing so

may result in damage, malfunction, or deterioration of performance

characteristics.

• When

replacing relays, there is a possibility the relay will pop out

and fall. Take care to prevent the relay from falling during

replacement.

• Where

vibration or shock is directly transmitted to the body

• Where

the socket could come into contact with a solvent or

alkaline agent

Push-In Plus Terminal Block

1. Connecting Wires to the Push-In Plus Terminal Block

Part Names of the Terminal Block

• Insert

the short bar into the insertion hole in the correct orientation,

and insert until all terminals are all the way in.

• If

using a short bar, install the short bar before performing wiring

work.

Release hole

rminal (Insertion) hole

• A

push-in Plus terminal block type and a screw terminal type have

different insertion positions, so a mixed installation using the same

short bar is not possible.

Connecting Wires with Ferrules and Solid Wires

Insert the solid wire or ferrule straight into the terminal block until the

end strikes the terminal block.

Orient correctly

and push all the

way in.

Release hole

rminal

(Insertion) hole

Ferrules or

solid wire

Completely inserted

• If

a wire is difficult to connect because it is too thin, use a flat-blade

screwdriver in the same way as when connecting stranded wire.

All terminals are inserted all the way in.

Connecting Stranded Wires

Use the following procedure to connect the wires to the terminal block.

(1) Hold a flat-blade screwdriver at an angle and insert it into the

release hole.

The angle should be between 10°and15°. If the flat-blade

screwdriver is inserted correctly, you will feel the spring in the

release hole.

(2) With the flat-blade screwdriver still inserted into the release hole,

insert the wire into the terminal hole until it strikes the terminal

block.

(3) Remove the flat-blade screwdriver from the release hole.

Flat-blade screwdriver

(3)

(1)

Incomplete insertion

All terminals are not inserted

all the way in.

Incorrect installation

Some terminals not inserted

completel

10 to 15°

(3)

(1)

(2)

Stranded Wires

Incomplete

insertion

Checking Connections

• After

the insertion, pull gently on the wire to make sure that it will

not come off and the wire is securely fastened to the terminal block.

• If

you use a ferrule with a conductor length of 10 mm, part of the

conductor may be visible after the ferrule is inserted into the

terminal block, but the product insulation distance will still be

satisfied.

• Do

not insert short bar in the hole for wire or screw driver, it may

cause the result of failure of pull out.

2. Removing Wires from the Push-In Plus Terminal Block

Use the following procedure to remove wires from the terminal block.

The same method is used to remove stranded wires, solid wires, and

ferrules.

(1) Hold a flat-blade screwdriver at an angle and insert it into the

release hole.

If insert short bar in the hole for wire or screw driver and try to pull

out, it may cause damage for short bar or socket and failure in

electric conductivity.

• Please

insert P2RVC terminal into the short bar insertion hole of

G2RV-SR/G3RV-SR. If insert P2RVC into the release hole or

terminal (insertion) hole wrongly, P2RVC may stuck and can not

remove and it may cause result of damage on P2RVC and G2RV-

SR/G3RV-SR.

(2) With the flat-blade screwdriver still inserted into the release hole,

remove the wire from the terminal insertion hole.

(3) Remove the flat-blade screwdriver from the release hole.

Flat-blade screwdriver

(3)

(1)

10 to 15°

Wire

(3)

Please turn off the power of input and output side and remove PLC

interface unit when replacing mounting relays and SSRs for

maintenance.

(1)

(2)

G2RV-SR/G3RV-SR

3. Recommended ferrules and Crimp Tools

Recommended ferrules

Recommended Flat-blade Screwdriver

Use a flat-blade screwdriver to connect and remove wires.

Use the following flat-blade screwdriver.

The following table shows manufacturers and models as of 2015/Dec.

Applicable

wire

Stripping

length

(mm)

(Ferrules

used)

Ferrules

Conduct

length

Recommended ferrules

Side

Front

Phoeni

ontact

Weidmuller

Wago

product

(mm

)

(AWG)

(mm)

product

2.5 mm dia.

AI 0,25-8

AI 0,25-10

AI 0,34-8

AI 0,34-10

AI 0,5-8

H0.25/12 216-301

— —

H0.34/12 216-302

0.25

0.34

0.5

0.4 mm

2.5 mm

—

H0.5/14

H0.5/16

216-201

216-241

Model

Manufacturer

AI 0,5-10

AI 0,75-8

AI 0,75-10

AI 1-8

ESD 0,40×2,5

SZS 0,4×2,5

SZF 0-0,4×2,5

0.4×2.5×75 302

AEF.2,5×75

Wera

H0.75/14 216-202

H0.75/16 216-242

Phoenix Contact

0.75

Wiha

H1.0/14

H1.0/16

H1.5/14

H1.5/16

216-203

216-243

216-204

216-244

Facom

Wago

1/1.25 18/17

1.25/1.5

17/16

AI 1-10

210-719

AI 1,5-8

SDI 0.4×2.5×75

Weidmuller

AI 1,5-10

OMRON’s exclusive purchase model XW4Z-00B is available to

order as SZF 0-0

4×2

5 (manufactured by Phoenix Contact).

CRIMPFOX6

Recommended crimp tool

CRIMPFOX6T-F

PZ6 roto

CRIMPFOX10S

Variocrimp4

Screw Terminal

• Screw terminal

Note: 1.

Make sure that the outer diameter of the wire is smaller than

the inner diameter of the insulating sleeve of the

recommended ferrule.

Applicable wire

size

Stripping

length

Wired type

Make sure that the ferrule processing dimensions conform

to the following figure.

Stranded wires, without

ferrule

0.5 to 1.5 mm

8 mm

Stranded wires, with ferrule

and plastic collar

8 mm

8 to 10 mm

Stranded wires with ferrule,

without plastic collar

0.5 to 1.5 mm

8 mm

2.6 mm max.

1.9 mm max.

Single wire

If you use AWG24 to AWG22 (0.25 to 0.34 mm

) wires, UL

certification will not apply.

• Tightening Torque

0.4 N • m

• Electric wiring

Use the electric wire of specified size as shown above. The length

of the that is not covered is 8 mm.

Screw terminal

8 mm

Stripping length

<G2RV>

Operating latching lever (test switch)

When operating the latching lever for G2RV-SR701/501

series, use a 2.5 mm width flat-blade screwdriver.

• Applicable

flat-blade screwdriver

Flat-blade screwdriver with parallel cutting edge: shaft diameter

2.5 mm (3.0 mm max.)

Parallel cutting edge flat-blade screwdriver

Shaft diameter 2.5 mm (3.0 mm max.)

Wide flat-blade screwdriver

Driver with a thick shaft cannot be used.

• Always

turn OFF the power supply before operating latching lever.

• Return

to its original state after using the latching lever.

G2RV-SR/G3RV-SR

• Do

not use the latching lever as a switch.

• Operation

durability of the latching lever is 100 times or more.

• Do

not keep the latching lever ON for a long period of time (24

hours or more) in order to maintain the operation check function.

Incorrect Example

Countermeasure 1

Recommended height of the duct is

1/2 or less of the height of the SSR

Countermeasure 2

Duct or other object

blocking airflow

Duct or other object

blocking airflow

Duct or

Method of operation of the latching lever (test

switch)

other object

blocking

airflow

Airflow

Height of SSR

Contact normal position

Vertical

Direction

Metal

base

SSR

Contact operating position (on-state)

SSR

Close protective cover

Open protective cover

Duct or other object

blocking airflow

Duct or other object

blocking airflow

Duct or other object

blocking airflow

Do not enclose the SSR in a

duct of the same height.

It will interfere with the heat

dissipation of SSR.

Use ducts that have a

shallow depth, to provide a

place the SSR on a metal base so

sufficient ventilation area.

that it is not surrounded by the ducts.

If the ducts cannot be made lower,

Be aware of airflow

Duct or other object

blocking airflow

Exhaust

(Axial fan)

Keep the protective cover open when using the latching lever. Move

until the latching lever clicks to the ON position (ON state). After use

latching lever, in order to prevent malfunction, return the switch to

contact normal position (OFF state), and make sure the protective

cover is firmly closed.

SSR

Using the latching lever

Example: check the operation of the relay and the sequence circuit

Inlet

<G3RV>

• If

the air inlet or air outlet has a filter, clean the filter regularly to

prevent it from clogging to ensure an efficient flow of air.

• Do

not place objects that may obstruct the proper ventilation for

outside or inside the inlet or exhaust port, and in the outside

vicinity.

• Since

the G3RV uses electronic components, do not allow it to fall,

vibrate, or apply shock that exceeds the criteria. Doing so may

result in failure, malfunction, or deterioration of performance.

• Tighten

screw terminal for G3RV at torque 0.4 N · m. It may cause

short-circuit failure or burning.

• A

heat exchanger, if used, should be located in front of the G3RV

to ensure the efficiency of the heat exchanger.

• Please

use the voltage and current suitable for the input and

output terminal portion of G3RV. It may cause short-circuit failure

or burning.

• Please

observe the ambient temperature of G3RV. The rated

current of the G3RV is measured at an ambient temperature of

25°C.

Mounting

• The

G3RV uses a semiconductor in the output element.

This causes the temperature inside the control panel to increase

due to heating resulting from the flow of electrical current through

the load. The G3RV reliability can be increased by adding a

ventilation fan to the control panel to dispel this heat, thus lowering

the ambient temperature of the G3RV.

Duct or other object blocking airflow

60 mm min.

10 mm min.

SSR

(It suggests that life expectancy is doubled by each 10°C reduction

in ambient temperature.)

Vertical Direction

EMI

The G3RV is a Class A product (for industrial environments). When

used in a residential environment, it may cause radio interference.

In such case, the user may be required to take appropriate

measures.

30 mm min.

80 mm min.

When five or more are installed, install with 10 mm space between

each.

G2RV-SR/G3RV-SR

For G2RV-SR/G3VR-SR

Common Accessories (order separately)

Ordering Information

Short Bars

No. of

poles

Minimum order

(Quantity)

Maximum energizing

current

Appearance

Pitch

Colors

Model *

PYDN-6.2-020

PYDN-6.2-030

PYDN-6.2-040

PYDN-6.2-100

PYDN-6.2-200

Red (R),

Blue (S),

Yellow (Y)

6.2 mm

32 A

Note:

Use for wiring to the adjacent socket.

Replace the box (

) in the model number with the code for the covering color.

color selection: R = red, S = blue, Y = yellow

Label

Minimum order (Sheet)

(Pieces per sheet)

Appearance

Model

XW5Z-P2.5LB1

(1 sheet/72 pieces)

XW5Z-P2.5LB2

Available following June 2017 production.

Separate Plate

Appearance

Model

XW5Z-EP12

PLC interface unit

Appearance

I/O classification

Connection method

Common process

Applicable Models

G2RV-SR500-AP

Model

P2RVC-8-I-5-1

P2RVC-8-I-5

PNP

NPN

PNP

NPN

Push-In

Screw

For input

G2RV-SR700-AP

P2RVC-8-I-7-1

P2RVC-8-O-5-1

P2RVC-8-O-5

G2RV-SR500

G2RV-SR501

G3RV-SR500

Push-In

For output

G2RV-SR700

G2RV-SR701

G3RV-SR700

Screw

PNP

P2RVC-8-O-7-1

Please make sure applicable models, P2RVC can not be used other combination than the above table.

Parts for DIN Track Mounting

Minimum order

(Quantity)

Appearance

Type

Model

1 m

PFP-100N

PFP-50N

DIN Tracks

0.5 m

End Plate

PFP-M

PFP-S

Spacer

When mounting DIN Track, please use End Plate (PFP-M).

Refer to your OMRON website for details on PFP-

G2RV-SR/G3RV-SR

Applicable Cables

Cable

length L

(mm)

Name

Appearance

Connecting Cables

Applicable Connectors

1,000

2,000

3,000

5,000

P2RV-A100C

P2RV-A200C

P2RV-A300C

P2RV-A500C

End A

Device

end

End B

PLC interface

unit end

Cables with Loose

8 I/O

Wires

Various devices

points

P2RV-A

P2RV-4-100C

1,000

2,000

3,000

5,000

1,000

2,000

3,000

5,000

1,000

2,000

3,000

5,000

P2RV-4-200C

Cables with

32 output

PLC I/O Units with MIL connectors (1:4)

CJ1W-OD232/OD262, etc.

Connectors (1:4)

points

P2RV-4-

P2RV-4-300C

P2RV-4-500C

300

P2RV-4-100IMC

P2RV-4-200IMC

P2RV-4-300IMC

P2RV-4-500IMC

P2RV-4-100IFC

P2RV-4-200IFC

P2RV-4-300IFC

P2RV-4-500IFC

Cables with

32 input

PLC I/O Units with MIL connectors (1:4)

CJ1W-ID232/ID262, etc.

Connectors (1:4)

points

P2RV-4-

IMC

Cables with

32 input

PLC I/O Units with Fujitsu connectors (1:4)

CJ1W-ID231/ID261, etc.

Connectors (1:4)

points

P2RV-4-

IFC

P2RV-A050C-OMR GRT1

P2RV-A100C-OMR GRT1

P2RV-A050IC-OMR GRT1

P2RV-A100IC-OMR GRT1

P2RV-A050C-OMR NX

P2RV-A100C-OMR NX

P2RV-A050IC-OMR NX

P2RV-A100IC-OMR NX

500

1,000

500

8 output

Cables with Connectors

points

(1:1)

Slice I/O Units (1:1)

For inputs: GRT1-ID8-1

For outputs: GRT1-OD8-1

P2RV-A

C-OMR GRT1

8 input

points

1,000

500

Removable

terminal block

8 output

PLC I/O Units with screw-less clamp

terminal block (1:1)

For inputs: NX-ID4442

points

Cables with

1,000

500

Connectors (1:1)

P2RV-A

C-OMR NX

8 input

For outputs: NX-OD4256

points

1,000

G2RV-SR/G3RV-SR

Cable

length L

(mm)

Name

Appearance

Connecting Cables

Applicable Connectors

P2RV-050C-SCH-A

P2RV-100C-SCH-A

P2RV-200C-SCH-A

P2RV-300C-SCH-A

P2RV-500C-SCH-A

P2RV-050C-SCH-B

P2RV-100C-SCH-B

P2RV-200C-SCH-B

P2RV-300C-SCH-B

P2RV-500C-SCH-B

P2RV-050C-SCH-C

P2RV-100C-SCH-C

P2RV-200C-SCH-C

P2RV-300C-SCH-C

P2RV-500C-SCH-C

P2RV-050C-SCH-D

P2RV-100C-SCH-D

P2RV-200C-SCH-D

P2RV-300C-SCH-D

P2RV-500C-SCH-D

P2RV-050C-SIM-A

P2RV-100C-SIM-A

P2RV-200C-SIM-A

P2RV-300C-SIM-A

P2RV-500C-SIM-A

P2RV-050C-SIM-B

P2RV-100C-SIM-B

P2RV-200C-SIM-B

P2RV-300C-SIM-B

P2RV-500C-SIM-B

500

End A

ice

end

End B

PLC interface

1,000

2,000

3,000

5,000

500

32 input

points

nit end

Schneider Electric PLCs with 32-point

connectors (1:4)

For inputs: 140 DDI 353 00

For outputs: 140 DDO 353 00

1,000

2,000

3,000

5,000

500

32 output

points

Schneider Electric

PLC Connecting

Cables

300

P2RV-

C-SCH-

1,000

2,000

3,000

5,000

500

16 input

points

Schneider Electric PLCs with

16-point connectors (1:2)

For inputs: BMX DDI 1602

For outputs: BMX DDO 1602

1,000

2,000

3,000

5,000

500

16 output

points

300

1,000

2,000

3,000

5,000

500

32 input

points

Siemens PLCs with

32-point connectors (1:4)

For inputs: 6ES7 321-1BL00-0AA0

For outputs: 6ES7 322-1BL00-0AA0

1,000

2,000

3,000

5,000

32 output

points

300

P2RV-050C-SIM-C

P2RV-100C-SIM-C

P2RV-200C-SIM-C

P2RV-300C-SIM-C

P2RV-500C-SIM-C

500

1,000

2,000

3,000

5,000

Siemens PLC

Connecting Cables

P2RV-

C-SIM-

Siemens PLCs with

16-point connectors (1:2)

For inputs: 6ES7 321-1BH02-0AA0

16 input

points

P2RV-050C-SIM-D

P2RV-100C-SIM-D

P2RV-200C-SIM-D

P2RV-300C-SIM-D

P2RV-500C-SIM-D

P2RV-050C-SIM-E

P2RV-100C-SIM-E

P2RV-200C-SIM-E

P2RV-300C-SIM-E

P2RV-500C-SIM-E

500

1,000

2,000

3,000

5,000

500

32 input

points

Siemens PLCs with

32-point connectors (1:4)

For inputs: 6ES7 421-1BL-0AA0

For outputs: 6ES7 422-1BL-0AA0

1,000

2,000

3,000

5,000

32 output

points

G2RV-SR/G3RV-SR

PLC interface unit

Ratings / characteristices

Rated voltage

30 VAC/DC

Rated current

0.5 A/poles, 2 A/unit

Ambient operating temperature

−

40 to 55°C

Destruction

10 to 55 to 10 Hz, single amplitude 0.75 mm (double amplitude 1.5 mm)

Vibration resistance

Shock resistance

Malfunction

Destruction

Malfunction

10 to 55 to 10 Hz, single amplitude 0.75 mm (double amplitude 1.5 mm)

300 m/s

100 m/s

Electrical schematic

Input

P2RVC-8-I-

-1 (PNP)

P2RVC-8-I-5 (NPN)

1………………..8

Output

P2RVC-8-O-

-1 (PNP)

P2RVC-8-O-5 (NPN)

1………………..8

G2RV-SR/G3RV-SR

Dimensions

(unit: mm)

PLC interface unit

Push-I

P2RVC-8-I-5(-1)

P2RVC-8-O-5(-1)

49.60

67.16

12.68

7×6.20

Screw

P2RVC-8-I-7-1

P2RVC-8-O-7-1

49.60

67.16

12.68

7×6.20

G2RV-SR/G3RV-SR

(Except for PLC interface unit)

Common Accessories (order separately)

Dimensions

(unit: mm)

Short Bars

PYDN-6.2-

(6.2 mm)

Maximum carry

Pitch

No. of poles

L (Length)

Colors

Model

current

12.4

18.6

24.8

PYDN-6.2-020

PYDN-6.2-030

PYDN-6.2-040

PYDN-6.2-100

PYDN-6.2-200

1.20

Red (R)

Blue (S)

Yellow (Y)

6.2 mm

32 A

124

6.20

Note:

Use the Short Bars for crossover wiring within one Socket or between Sockets.

Replace the box (

) in the model number with the code for the covering color.

Separate Plate

XW5Z-EP12

Parts for DIN Track Mounting

Refer to your OMRON website for details on the PFP-

Safety Precautions

Precautions for Correct Use

When mounting a short bar

• Intermediate

pins can be bent by a tool or by hand and cut off for use.

Mounting a separate plate

• Use

a flat-blade screwdriver to tighten the center top screw and

secure the plate. Loosen the screw to remove the plate from the

DIN rail.

M4 Screw

Bend

Cut off

• The

short bar can be cut to as many poles as needed. Insert the

tool from the plastic part side, and cut along the groove in the

plastic part between the terminals. When cutting, take care not to

break or deform the terminals.

However, because the metal on the cut surface will be exposed,

insulation countermeasures between adjacent products must be

ensured. Such countermeasures include widening the intervals

between products or using XW5Z-EP12 separate plates (order

separately).

Cut

Terms and Conditions Agreement

Read and understand this catalog.

Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have

any questions or comments.

Warranties.

(a) Exclusive Warrant

mron’s exclusive warranty is that the Products will be free from defects in materials and workmanship

for a period of twelve months from the date of sale by Omron (or such other period expressed in writing

by Omron). Omron disclaims all other warranties, express or implied.

(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESEN

ION, EXPRESS OR IMPLIED, ABOUT

NON-INFRINGEMEN

ERCHAN

BILITY OR FITNESS FOR A

RTICULAR PURPOSE OF THE

PRODUCTS. BUYER ACKNOWLEDGES TH

T ALONE HAS DETERMINED TH

HE PRODUCTS WILL

SUI

EET THE REQUIREMENTS OF THEIR INTENDED USE.

Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products

or otherwise of any intellectual property right. (c) Buyer Remed

mron’s sole obligation hereunder shall be, at Omron’s election,

to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the

non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price

of the non-complying Product; provided that in no event shall Omron be responsible for warrant

epair, indemnity or any other

claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored,

installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by

Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or

unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system

assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in

writing, are not to be construed as an amendment or addition to the above warrant

See http://www.omron.com/global/ or contact your Omron representative for published information.

Limitation on Liability; Etc.

OMRON COM

NIES SHALL NOT BE LIABLE FOR SPECIAL, INDIREC

NCIDEN

L, OR CONSEQUENTIAL DAMAGES,

LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY W

ONNECTED WITH THE PRODUCTS,

WHETHER SUCH CLAIM IS BASED IN CONTRAC

, WARRANT

EGLIGENCE OR STRICT LIABILIT

Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.

Suitability of Use.

Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the

combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable

third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is

not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system,

or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with

respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.

NEVER USE THE PRODUCT FOR AN APPLIC

ION INVO

ING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE

QUANTITIES WITHOUT ENSURING TH

HE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,

AND TH

HE OMRON PRODUCT(S) IS PROPER

ED AND INS

LLED FOR THE INTENDED USE WITHIN THE

OVERALL EQUIPMENT OR SYSTEM.

Programmable Products.

Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof.

Performance Data.

Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining

suitability and does not constitute a warrant

t may represent the result of Omron’s test conditions, and the user must correlate it

to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liabilit

Change in Specifications.

Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice

to change part numbers when published ratings or features are changed, or when significant construction changes are made.

However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be

assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to

confirm actual specifications of purchased Product.

Errors and Omissions.

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is

assumed for clerical, typographical or proofreading errors or omissions.

OMRON Corporation

Kyoto, JAPAN

Industrial Automation Company

Authorized Distributor:

Contact: www.ia.omron.com

Regional Headquarters

OMRON EUROPE B.

Wegalaan 67-69, 2132 JD Hoofddorp

The Netherlands

OMRON ELECTRONICS LLC

2895 Greenspoint Parkwa

uite 200

Hoffman Estates, IL 60169 U.S.A.

l: (31)2356-81-300/Fax: (31)2356-81-388

l: (1) 847-843-7900/Fax: (1) 847-843-7787

In the interest of product improvement,

specifications are subject to change without notice.

OMRON (CHINA) CO., LTD.

Room 2211, Bank of China

wer,

200 Yin Cheng Zhong Road,

OMRON ASIA

ACIFIC PTE. LTD.

No. 438A Alexandra Road # 05-05/08 (Lobby 2),

Alexandra

chnopark,

PuDong New Area, Shanghai, 200120, China

l: (86) 21-5037-2222/Fax: (86) 21-5037-2200

CSM_

Cat. No. J214-E1-02

Singapore 119967

l: (65) 6835-3011/Fax: (65) 6835-2711

0617(0316)

Omron-Electronics-G2RV-1SG-DC21

Related Posts

CUI-CPE-171

DB-Unlimited-TP243408-1

DB-Unlimited-TE054003-2