Phoenix-Contact-2900295
| Part # | Phoenix-Contact-2900295 |
Download  | Phoenix-Contact-2900295 |
Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user’s
documentation. Our General Terms of Use for Downloads are valid
(http://phoenixcontact.com/download)
PLC-INTERFACE for high continuous currents, consisting of PLC-BPT…/21 HC basic terminal block with
Push-in connection and plug-in miniature relay, for mounting on DIN rail NS 35/7,5, limiting continuous current
up to 10 A, 1 changeover contact, input voltage 60 V DC
Your advantages
Long electrical service life thanks to 16 A relay
All common input voltages of 12 V DC to 230 V AC
Efficient connection to system cabling using V8 adapter
Safe isolation according to DIN EN 50178 between coil and contact
Max. continuous current of 10 A
Functional plug-in bridges
Key Commercial Data
Packing unit
10 pc
GTIN
GTIN
4046356507066
Technical data
Note
EMC: class A product, see manufacturer’s declaration in the download
area
Utilization restriction
Dimensions
Width
Height
Depth
14 mm
80 mm
94 mm
Ambient conditions
Ambient temperature (operation)
Ambient temperature (storage/transport)
Degree of protection
-40 °C … 60 °C
-40 °C … 85 °C
RT II (Relay)
03/12/2021 Page
1 / 17
Technical data
Ambient conditions
IP20 (Relay base)
Coil side
Nominal input voltage U
N
Typical input current at U
N
Typical response time
Typical release time
Protective circuit
60 V DC
10 mA
8 ms
10 ms
Reverse polarity protection Polarity protection diode
Free-wheeling diode Damping diode
Operating voltage display
Yellow LED
0.6 W
Power dissipation for nominal condition
Contact side
Contact type
1 changeover contact
Single contact
AgNi
Type of switch contact
Contact material
250 V AC/DC (The separating plate PLC-ATP should be installed for
voltages larger than 250 V (L1, L2, L3) between identical terminal blocks
in adjacent modules. Potential bridging is then carried out with FBST 8-
PLC… or …FBST 500…)
Maximum switching voltage
Minimum switching voltage
Min. switching current
12 V (at 10 mA)
10 mA (at 12 V)
30 A (300 ms)
10 A
Maximum inrush current
Limiting continuous current
6 A (value applies to connections 12. If connections 12 are bridged, the
normal value applies.)
Interrupting rating (ohmic load) max.
240 W (at 24 V DC)
58 W (at 48 V DC)
48 W (at 60 V DC)
50 W (at 110 V DC)
80 W (at 220 V DC)
2500 VA (for 250 V AC)
144 W (for 24 V DC. Value applies to connections 12. If connections 12
are bridged, the normal value applies.)
Interrupting rating (ohmic load) max. bridged
Switching capacity
1500 VA (for 250 V AC. Value applies to connections 12. If connections
12 are bridged, the normal value applies.)
2 A (at 24 V, DC13)
0.2 A (at 110 V, DC13)
0.2 A (at 250 V, DC13)
6 A (at 24 V, AC15)
6 A (at 120 V, AC15)
6 A (at 250 V, AC15)
General
03/12/2021 Page
2 / 17
Technical data
General
Operating mode
100% operating factor
V0 (Housing)
Flammability rating according to UL 94
Mechanical service life
Mounting position
3x 10
7
cycles
any
Assembly instructions
In rows with zero spacing
Connection data
Connection name
Coil side
Connection method
Push-in connection
8 mm
Stripping length
Conductor cross section solid
Conductor cross section flexible
0.14 mm² … 2.5 mm²
0.14 mm² … 2.5 mm²
0.2 mm² … 2.5 mm² (Single ferrule)
2x 0.5 mm² … 1 mm² (TWIN ferrule)
26 … 14
Conductor cross section AWG
Connection data 2
Connection name
Contact side
Connection method
Push-in connection
8 mm
Stripping length
Conductor cross section solid
Conductor cross section flexible
0.14 mm² … 2.5 mm²
0.14 mm² … 2.5 mm²
0.2 mm² … 2.5 mm² (Single ferrule)
2x 0.5 mm² … 1 mm² (TWIN ferrule)
26 … 14
Conductor cross section AWG
Standards and Regulations
Connection in acc. with standard
Designation
CUL
Standards/regulations
Standards/regulations
IEC 60664
EN 50178
Rated surge voltage
Insulation
6 kV
Safe isolation, reinforced insulation
Pollution degree
Overvoltage category
2
III
Conformance/approvals
Designation
Identification
Corrosive gas test
ISA-S71.04. G3 Harsh Group
EN 60068-2-60
Environmental Product Compliance
REACh SVHC
Lead 7439-92-1
03/12/2021 Page
3 / 17
Technical data
Environmental Product Compliance
China RoHS
Environmentally Friendly Use Period = 50 years
For details about hazardous substances go to tab “Downloads”,
Category “Manufacturer’s declaration”
Drawings
Diagram
Diagram
20
10
U
U
1,4
1,3
1,2
1,1
1
1
6
N
4
A
2
3
2
1
0,5
0,3
0,2
U
N
= 60 V DC
0,1
0,9
0,8
0,7
10
20
30
50 70
100
200 300
Switching voltage [V]
B
1
2
3
AC, ohmic load
DC, ohmic load
DC, L/R = 40 ms
20 25 30 35 40 45 50 55 60 65
T
[
C]
°
U
Interrupting rating
Curve A
Maximum permissible continuous voltage U
max
with limiting continuous
current on the contact side (see relevant technical data)
Curve B
Minimum permissible operate voltage U
op
after pre-excitation (see
relevant technical data)
Circuit diagram
11
A2
A1
14
12
Articles in set
14 mm PLC basic terminal block for high continuous currents with Push-in connection, without relay or solid-state
relay, for mounting on DIN rail NS 35/7,5, 1 changeover contact, input voltage 60 V DC
03/12/2021 Page
4 / 17
Articles in set
Plug-in miniature power relay, with power contact for high continuous currents, 1 changeover contact, 60 V DC
Classifications
eCl@ss
eCl@ss 10.0.1
eCl@ss 11.0
eCl@ss 4.0
eCl@ss 4.1
eCl@ss 5.0
eCl@ss 5.1
eCl@ss 6.0
eCl@ss 7.0
eCl@ss 9.0
27371601
27371601
27371000
27371000
27371600
27371600
27371600
27371601
27371601
ETIM
ETIM 2.0
ETIM 3.0
ETIM 4.0
ETIM 5.0
ETIM 6.0
ETIM 7.0
EC001437
EC001437
EC001437
EC001437
EC001437
EC001437
UNSPSC
UNSPSC 6.01
UNSPSC 7.0901
UNSPSC 11
30211916
39121515
39121515
39121515
39122334
39122334
39122334
39122334
39122334
UNSPSC 12.01
UNSPSC 13.2
UNSPSC 18.0
UNSPSC 19.0
UNSPSC 20.0
UNSPSC 21.0
Approvals
Approvals
03/12/2021 Page
5 / 17
Approvals
Approvals
UL Listed / UL Recognized / cUL Recognized / cUL Listed / RC FRT / EAC / EAC / DNV GL / cULus Recognized / cULus Listed
Ex Approvals
Approval details
UL Listed
UL Recognized
cUL Recognized
cUL Listed
RC FRT
FILE E 172140
FILE E 238705
FILE E 238705
FILE E 172140
B.00094
EAC
TR_TS_D_00573_c
RU*C-
DE.*08.B.00010
EAC
DNV GL
TAE0000196-03
03/12/2021 Page
6 / 17
Approvals
cULus Recognized
cULus Listed
Accessories
Accessories
Bridge
Continuous plug-in bridge, length: 500 mm, color: red
Continuous plug-in bridge, length: 500 mm, color: blue
Continuous plug-in bridge, length: 500 mm, color: gray
Single plug-in bridge, length: 6 mm, number of positions: 2, color: red
03/12/2021 Page
7 / 17
Accessories
Single plug-in bridge, length: 6 mm, number of positions: 2, color: blue
Single plug-in bridge, length: 6 mm, number of positions: 2, color: gray
Single plug-in bridge, length: 8 mm, number of positions: 2, color: gray
Single plug-in bridge, length: 14 mm, number of positions: 2, color: black
DIN rail
DIN rail perforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized,
passivated with a thick layer, length: 2000 mm, color: silver
03/12/2021 Page
8 / 17
Accessories
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized,
passivated with a thick layer, length: 2000 mm, color: silver
DIN rail perforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, Galvanized,
white passivated, length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, Galvanized,
white passivated, length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Aluminum,
uncoated, length: 2000 mm, color: silver
DIN rail perforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized,
length: 2000 mm, color: silver
03/12/2021 Page
9 / 17
Accessories
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized,
length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Copper, uncoated,
length: 2000 mm, color: copper-colored
DIN rail end piece, for DIN rail NS 35/7.5
DIN rail perforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel, galvanized,
passivated with a thick layer, length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel,
galvanized, passivated with a thick layer, length: 2000 mm, color: silver
03/12/2021 Page
10 / 17
Accessories
DIN rail perforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel, Galvanized,
white passivated, length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel,
Galvanized, white passivated, length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Aluminum,
uncoated, length: 2000 mm, color: silver
DIN rail perforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel, galvanized,
length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel,
galvanized, length: 2000 mm, color: silver
03/12/2021 Page
11 / 17
Accessories
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Copper,
uncoated, length: 2000 mm, color: copper-colored
DIN rail end piece, for DIN rail NS 35/15
DIN rail, unperforated, Standard profile 2.3 mm, width: 35 mm, height: 15 mm, acc. to EN 60715, material: Steel,
galvanized, passivated with a thick layer, length: 2000 mm, color: silver
Labeled terminal marker
Zack marker strip, can be ordered: Strip, white, labeled according to customer specifications, mounting type: snap
into tall marker groove, for terminal block width: 10.2 mm, lettering field size: 10.15 x 10.5 mm, Number of individual
labels: 10
Zack marker strip, Strip, white, labeled, can be labeled with: CMS-P1-PLOTTER, printed horizontally: consecutive
numbers 1 … 10, 11 … 20, etc. up to 91 … 100, mounting type: snap into tall marker groove, for terminal block width:
10.2 mm, lettering field size: 10.15 x 10.5 mm, Number of individual labels: 10
03/12/2021 Page
12 / 17
Accessories
Zack marker strip, Strip, white, labeled, can be labeled with: CMS-P1-PLOTTER, Printed vertically: consecutive
numbers 1 … 10, 11 … 20, etc. up to 91 … 100, mounting type: snap into tall marker groove, for terminal block width:
10.2 mm, lettering field size: 10.15 x 10.5 mm, Number of individual labels: 10
Marker for terminal blocks, Strip, white, labeled, can be labeled with: CMS-P1-PLOTTER, horizontal: L1, L2, L3, N,
PE, L1, L2, L3, N, PE, mounting type: snap into tall marker groove, for terminal block width: 10.2 mm, lettering field
size: 10.15 x 10.5 mm, Number of individual labels: 10
Marker for terminal blocks, Strip, white, labeled, can be labeled with: CMS-P1-PLOTTER, horizontal: U, V, W, N,
GND, U, V, W, N, GND, mounting type: snap into tall marker groove, for terminal block width: 10.2 mm, lettering field
size: 10.15 x 10.5 mm, Number of individual labels: 10
Marker for terminal blocks, can be ordered: by sheet, white, labeled according to customer specifications, mounting
type: snap into tall marker groove, for terminal block width: 10.2 mm, lettering field size: 9.6 x 10.5 mm, Number of
individual labels: 48
Marker for terminal blocks, can be ordered: by sheet, white, labeled according to customer specifications, mounting
type: snap into tall marker groove, for terminal block width: 10.2 mm, lettering field size: 8.9 x 9.6 mm, Number of
individual labels: 36
03/12/2021 Page
13 / 17
Accessories
Zack marker strip, can be ordered: Strip, white, labeled according to customer specifications, mounting type: snap
into tall marker groove, for terminal block width: 12.2 mm, lettering field size: 10.5 x 12.15 mm, Number of individual
labels: 5
Zack marker strip, Strip, white, labeled, printed horizontally: L1, L2, L3, N, PE, mounting type: snap into tall marker
groove, for terminal block width: 12.2 mm, lettering field size: 10.5 x 12.15 mm, Number of individual labels: 5
Marker for terminal blocks, can be ordered: by sheet, white, labeled according to customer specifications, mounting
type: snap into tall marker groove, for terminal block width: 12 mm, lettering field size: 11.45 x 10.5 mm, Number of
individual labels: 40
Marker for terminal blocks, can be ordered: by sheet, white, labeled according to customer specifications, mounting
type: snap into tall marker groove, for terminal block width: 12 mm, lettering field size: 10.8 x 9.6 mm, Number of
individual labels: 30
Partition plate
Separating plate, 2 mm thick, required at the start and end of a PLC terminal strip. Furthermore, it is used for: visual
separation of groups, safe isolation of different voltages of neighboring PLC relays in acc. with DIN VDE 0106-101,
isolation
Power module
03/12/2021 Page
14 / 17
Accessories
Power terminal block, for the input of up to four potentials, for mounting on NS 35/7.5
Screwdriver tools
Actuation tool, for ST terminal blocks, also suitable for use as a bladed screwdriver, size: 0.6 x 3.5 x 100 mm, 2-
component grip, with non-slip grip
Terminal marking
Zack marker strip, Strip, white, unlabeled, can be labeled with: PLOTMARK, CMS-P1-PLOTTER, mounting type:
snap into tall marker groove, for terminal block width: 10.2 mm, lettering field size: 10.5 x 10.15 mm, Number of
individual labels: 10
Marker for terminal blocks, Sheet, white, unlabeled, can be labeled with: BLUEMARK ID COLOR, BLUEMARK ID,
BLUEMARK CLED, PLOTMARK, CMS-P1-PLOTTER, mounting type: snap into tall marker groove, for terminal block
width: 10.2 mm, lettering field size: 9.6 x 10.5 mm, Number of individual labels: 48
Marker for terminal blocks, Sheet, white, unlabeled, can be labeled with: TOPMARK NEO, TOPMARK LASER,
BLUEMARK ID COLOR, BLUEMARK ID, BLUEMARK CLED, THERMOMARK PRIME, THERMOMARK CARD 2.0,
THERMOMARK CARD, mounting type: snap into tall marker groove, for terminal block width: 10.2 mm, lettering field
size: 8.9 x 9.6 mm, Number of individual labels: 36
03/12/2021 Page
15 / 17
Accessories
Zack marker strip, Strip, white, unlabeled, can be labeled with: PLOTMARK, CMS-P1-PLOTTER, mounting type:
snap into tall marker groove, for terminal block width: 12.2 mm, lettering field size: 12 x 10.5 mm, Number of
individual labels: 5
Marker for terminal blocks, Sheet, white, unlabeled, can be labeled with: BLUEMARK ID COLOR, BLUEMARK ID,
BLUEMARK CLED, PLOTMARK, CMS-P1-PLOTTER, mounting type: snap into tall marker groove, for terminal block
width: 12 mm, lettering field size: 11.45 x 10.5 mm, Number of individual labels: 40
Marker for terminal blocks, Sheet, white, unlabeled, can be labeled with: TOPMARK NEO, TOPMARK LASER,
BLUEMARK ID COLOR, BLUEMARK ID, BLUEMARK CLED, THERMOMARK PRIME, THERMOMARK CARD 2.0,
THERMOMARK CARD, mounting type: snap into tall marker groove, for terminal block width: 12 mm, lettering field
size: 10.8 x 9.6 mm, Number of individual labels: 30
Spare parts
14 mm PLC basic terminal block for high continuous currents with Push-in connection, without relay or solid-state
relay, for mounting on DIN rail NS 35/7,5, 1 changeover contact, input voltage 60 V DC
Plug-in miniature power relay, with power contact for high continuous currents, 1 changeover contact, 60 V DC
03/12/2021 Page
16 / 17
Phoenix Contact 2021 © – all rights reserved
PHOENIX CONTACT GmbH & Co. KG
Flachsmarktstr. 8
32825 Blomberg
Germany
Tel. +49 5235 300
Fax +49 5235 3 41200
03/12/2021 Page
17 / 17
