Phoenix-Contact-2906224
| Part # | Phoenix-Contact-2906224 |
Download  | Phoenix-Contact-2906224 |
Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user’s
documentation. Our General Terms of Use for Downloads are valid
(http://phoenixcontact.com/download)
Pre-assembled relay module with Push-in connection, consisting of: relay base, power contact relay, plug-
in display/interference suppression module, and retaining bracket. Contact type: 1 changeover contact. Input
voltage: 12 V DC
Product Description
The pluggable electromechanical and solid-state relays in the RIFLINE complete product range and the base are recognized and approved in
accordance with UL 508.
The relevant approvals can be called up at the individual components in question.
Key Commercial Data
Packing unit
10 pc
GTIN
GTIN
4055626047430
Technical data
Note
EMC: class A product, see manufacturer’s declaration in the download
area
Utilization restriction
Type of note
Note
Notes on operation
FBS 2-6… plug-in bridge for the input side (A2) and FBS-2-8… plug-in
bridge for the output side (11/21)
Dimensions
Width
Height
Depth
16 mm
93 mm
75 mm
Ambient conditions
Ambient temperature (operation)
Ambient temperature (storage/transport)
Degree of protection
-40 °C … 70 °C
-40 °C … 85 °C
IP20 (Relay base)
RT III (Relay)
03/12/2021 Page
1 / 18
Technical data
Coil side
Nominal input voltage U
N
Input voltage range in reference to U
N
Typical input current at U
N
Typical response time
12 V DC
see diagram
33 mA
8 ms
Typical release time
10 ms
Coil voltage
12 V DC
Damping diode
Yellow LED
0.4 W
Protective circuit
Operating voltage display
Power dissipation for nominal condition
Contact side
Contact type
1 changeover contact
Single contact
Type of switch contact
Contact material
AgNi
Maximum switching voltage
Minimum switching voltage
Min. switching current
Maximum inrush current
Limiting continuous current
Interrupting rating (ohmic load) max.
250 V AC/DC
12 V (at 10 mA)
10 mA (at 12 V)
50 A (20 ms, N/O contacts)
11 A (see diagram)
264 W (at 24 V DC)
58 W (at 48 V DC)
48 W (at 60 V DC)
50 W (at 110 V DC)
80 W (at 220 V DC)
2750 VA (for 250 V AC)
2 A (at 24 V, DC13)
0.2 A (at 110 V, DC13)
0.2 A (at 250 V, DC13)
6 A (at 24 V, AC15)
6 A (at 120 V, AC15)
6 A (at 250 V, AC15)
Switching capacity
General
4 kV
rms
(50 Hz, 1 min., winding/contact)
100% operating factor
Test voltage
Operating mode
Flammability rating according to UL 94
Mechanical service life
Service life, electrical
Mounting position
V2 (Housing)
approx. 3x 10
7
cycles
see diagram
any
Assembly instructions
In rows with zero spacing
Connection data
03/12/2021 Page
2 / 18
Technical data
Connection data
Connection name
Coil side
Connection method
Push-in connection
Stripping length
8 mm
Conductor cross section solid
Conductor cross section flexible
0.14 mm² … 1.5 mm²
0.14 mm² … 1.5 mm²
0.14 mm² … 1.5 mm² (Ferrule with plastic sleeve)
0.14 mm² … 1 mm² (Ferrule with plastic sleeve, two conductors on
double terminal block)
Conductor cross section AWG
26 … 16 (solid)
26 … 16 (flexible)
Connection data 2
Connection name
Contact side
Connection method
Push-in connection
Stripping length
8 mm
Conductor cross section solid
Conductor cross section flexible
0.14 mm² … 1.5 mm²
0.14 mm² … 1.5 mm²
0.14 mm² … 1.5 mm² (Ferrule with plastic sleeve)
0.14 mm² … 1 mm² (Ferrule with plastic sleeve, two conductors on
double terminal block)
Conductor cross section AWG
26 … 16 (solid)
26 … 16 (flexible)
Standards and Regulations
Standards/regulations
Rated insulation voltage
Rated surge voltage
Insulation
DIN EN 50178
250 V AC
6 kV
safe isolation
Pollution degree
2
Overvoltage category
III
Conformance/approvals
Designation
Identification
Corrosive gas test
ISA-S71.04. G3 Harsh Group
EN 60068-2-60
Environmental Product Compliance
China RoHS
Environmentally Friendly Use Period = 50 years
For details about hazardous substances go to tab “Downloads”,
Category “Manufacturer’s declaration”
Drawings
03/12/2021 Page
3 / 18
Circuit diagram
Diagram
22
24
12
14
1,8
1,7
1,6
1,5
1,4
1,3
1,2
1,1
1,0
0,9
0,8
0,7
0,6
21
11
A2-
A1+
DC coils
20
30
40
50
60
70
80
Ambient temperature [°C]
DC coils
AC coils
Operating voltage range
Diagram
Diagram
13
12
20
10
11
10
9
6
4
8
2
1
7
6
5
0,5
4
0,3
0,2
3
2
0,1
1
10
20
30
50 70
100
200 300
20
30
DC coil
AC coil
40
50
60
70
80
Switching voltage [V]
Ambient temperature [°C]
AC, ohmic load
DC, ohmic load
DC, L/R = 40 ms
DC coil, jumper between 11 and 21
AC coil, jumper between 11 and 21
Interrupting rating
Contact derating
Diagram
Diagram
10
7
10
6
10
5
10
4
1
0,9
0,8
0,7
0,6
0,5
0,4
0,3
1
2
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
1
0,9
0,8
0,7
0,6
0,5
0,4
0,3
0,2
Switching current [A]
j
COS
1
2
250 V AC, ohmic load (DC coils)
250 V AC, ohmic load (AC coils)
Electrical service life
Service life reduction factor
03/12/2021 Page
4 / 18
Articles in set
Relay base RIF-1…, for miniature power relay with 1 or 2 changeover contacts or solid-state relays of the same
design, Push-in connection, plug-in option for input/interference suppression modules, for mounting on NS 35/7,5
Plug-in miniature power relay, with power contact for high continuous currents, 1 changeover contact, input voltage
12 V DC
Plug-in module, for mounting on RIF-1, RIF-2, RIF-3, and RIF-4, with freewheeling diode and yellow LED, polarity:
A1+, A2-, input voltage: 12 … 24 V DC ±30%
Relay retaining bracket, with ejector function and holder for marking material, suitable for RIF-1 relay base, for 16 mm
tall miniature power relay and solid-state relay
Classifications
eCl@ss
eCl@ss 10.0.1
eCl@ss 11.0
eCl@ss 5.0
eCl@ss 5.1
eCl@ss 6.0
eCl@ss 7.0
eCl@ss 9.0
27371601
27371601
27371600
27371600
27371600
27371601
27371601
ETIM
ETIM 2.0
EC001437
03/12/2021 Page
5 / 18
Classifications
ETIM
ETIM 3.0
ETIM 4.0
ETIM 5.0
ETIM 6.0
ETIM 7.0
EC001437
EC001437
EC001437
EC001437
EC001437
UNSPSC
UNSPSC 13.2
UNSPSC 18.0
UNSPSC 19.0
UNSPSC 20.0
UNSPSC 21.0
39122334
39122334
39122334
39122334
39122334
Approvals
Approvals
Approvals
EAC / EAC
Ex Approvals
Approval details
EAC
TR_TS_D_00573_c
RU*C-
DE.*08.B.00010
EAC
Accessories
Accessories
DIN rail
03/12/2021 Page
6 / 18
Accessories
DIN rail perforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized,
passivated with a thick layer, length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized,
passivated with a thick layer, length: 2000 mm, color: silver
DIN rail perforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, Galvanized,
white passivated, length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, Galvanized,
white passivated, length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Aluminum,
uncoated, length: 2000 mm, color: silver
03/12/2021 Page
7 / 18
Accessories
DIN rail perforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized,
length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized,
length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Copper, uncoated,
length: 2000 mm, color: copper-colored
DIN rail end piece, for DIN rail NS 35/7.5
DIN rail perforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel, galvanized,
passivated with a thick layer, length: 2000 mm, color: silver
03/12/2021 Page
8 / 18
Accessories
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel,
galvanized, passivated with a thick layer, length: 2000 mm, color: silver
DIN rail perforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel, Galvanized,
white passivated, length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel,
Galvanized, white passivated, length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Aluminum,
uncoated, length: 2000 mm, color: silver
DIN rail perforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel, galvanized,
length: 2000 mm, color: silver
03/12/2021 Page
9 / 18
Accessories
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel,
galvanized, length: 2000 mm, color: silver
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Copper,
uncoated, length: 2000 mm, color: copper-colored
DIN rail end piece, for DIN rail NS 35/15
DIN rail, unperforated, Standard profile 2.3 mm, width: 35 mm, height: 15 mm, acc. to EN 60715, material: Steel,
galvanized, passivated with a thick layer, length: 2000 mm, color: silver
End block
Quick mounting end clamp for NS 35/7,5 DIN rail or NS 35/15 DIN rail, with marking option, width: 9.5 mm, color:
gray
03/12/2021 Page
10 / 18
Accessories
Quick mounting end clamp for NS 35/7,5 DIN rail or NS 35/15 DIN rail, with marking option, with parking option for
FBS…5, FBS…6, KSS 5, KSS 6, width: 5.15 mm, color: gray
End clamp, width: 9.5 mm, color: gray
Insulating sleeve
Insulating sleeve, color: white
Insulating sleeve, color: red
Insulating sleeve, color: blue
03/12/2021 Page
11 / 18
Accessories
Insulating sleeve, color: yellow
Insulating sleeve, color: green
Insulating sleeve, color: gray
Insulating sleeve, color: black
Jumper
Plug-in bridge, pitch: 6.2 mm, width: 10.7 mm, number of positions: 2, color: red
03/12/2021 Page
12 / 18
Accessories
Plug-in bridge, pitch: 6.2 mm, width: 10.7 mm, number of positions: 2, color: blue
Plug-in bridge, pitch: 6.2 mm, width: 10.7 mm, number of positions: 2, color: gray
Plug-in bridge, pitch: 8.2 mm, width: 14.7 mm, number of positions: 2, color: red
Plug-in bridge, pitch: 8.2 mm, width: 14.7 mm, number of positions: 2, color: blue
Bridge for potential distribution
Labeled terminal marker
03/12/2021 Page
13 / 18
Accessories
Zack marker strip, can be ordered: Strip, white, labeled according to customer specifications, mounting type: snap
into tall marker groove, for terminal block width: 5.2 mm, lettering field size: 5.15 x 10.5 mm, Number of individual
labels: 10
Zack marker strip, Strip, white, labeled, printed horizontally: consecutive numbers 1 … 10, 11 … 20, etc. up to 491 …
500, mounting type: snap into tall marker groove, for terminal block width: 5.2 mm, lettering field size: 5.15 x 10.5
mm, Number of individual labels: 10
Zack marker strip, white, Printed vertically: consecutive numbers 1 … 10, 11 … 20, etc. up to 491 … 500, mounting
type: snap into tall marker groove, for terminal block width: 5.2 mm, lettering field size: 5.15 x 10.5 mm
Zack marker strip, Strip, white, labeled, can be labeled with: CMS-P1-PLOTTER, printed horizontally: Identical
numbers 1 or 2, etc. up to 100, mounting type: snap into tall marker groove, for terminal block width: 5.2 mm, lettering
field size: 5.15 x 10.5 mm, Number of individual labels: 10
Zack marker strip, Strip, white, labeled, horizontal: L1, L2, L3, N, PE, L1, L2, L3, N, PE, mounting type: snap into tall
marker groove, for terminal block width: 5.2 mm, lettering field size: 5.15 x 10.5 mm, Number of individual labels: 10
03/12/2021 Page
14 / 18
Accessories
Marker for terminal blocks, can be ordered: by sheet, white, labeled according to customer specifications, mounting
type: snap into tall marker groove, for terminal block width: 5.2 mm, lettering field size: 10.5 x 4.6 mm, Number of
individual labels: 96
Marker for terminal blocks, can be ordered: by sheet, white, labeled according to customer specifications, mounting
type: snap into tall marker groove, for terminal block width: 5.2 mm, lettering field size: 4.6 x 10.5 mm, Number of
individual labels: 72
Zack marker strip, can be ordered: Strip, white, labeled according to customer specifications, mounting type: snap
into tall marker groove, for terminal block width: 15.2 mm, lettering field size: 10.5 x 15.1 mm, Number of individual
labels: 5
Zack marker strip, Strip, white, labeled, printed horizontally: L1, L2, L3, N, PE, mounting type: snap into tall marker
groove, for terminal block width: 15.2 mm, lettering field size: 10.5 x 15.1 mm, Number of individual labels: 5
Marker carriers
Double marker carrier, snaps onto the double-level spring-cage terminal block STTB 2,5, STTB 4, PTTB 2,5, PTTB 4
can be marked with UC-TM 5, ZB 5 or UC-TMF 5, ZBF 5
Terminal marking
03/12/2021 Page
15 / 18
Accessories
Marker for terminal blocks, Sheet, white, unlabeled, can be labeled with: BLUEMARK ID COLOR, BLUEMARK ID,
BLUEMARK CLED, PLOTMARK, CMS-P1-PLOTTER, mounting type: snap into tall marker groove, for terminal block
width: 16 mm, lettering field size: 15.45 x 10.5 mm, Number of individual labels: 32
Marker for terminal blocks, Sheet, white, unlabeled, can be labeled with: BLUEMARK ID COLOR, BLUEMARK ID,
BLUEMARK CLED, PLOTMARK, CMS-P1-PLOTTER, mounting type: snap into flat marker groove, for terminal block
width: 16 mm, lettering field size: 15.45 x 5.1 mm, Number of individual labels: 32
Zack marker strip, Strip, white, unlabeled, can be labeled with: PLOTMARK, CMS-P1-PLOTTER, mounting type:
snap into tall marker groove, for terminal block width: 5.2 mm, lettering field size: 5.1 x 10.5 mm, Number of individual
labels: 10
Marker for terminal blocks, Sheet, white, unlabeled, can be labeled with: BLUEMARK ID COLOR, BLUEMARK ID,
BLUEMARK CLED, PLOTMARK, CMS-P1-PLOTTER, mounting type: snap into tall marker groove, for terminal block
width: 5.2 mm, lettering field size: 10.5 x 4.6 mm, Number of individual labels: 96
Marker for terminal blocks, Sheet, white, unlabeled, can be labeled with: TOPMARK NEO, TOPMARK LASER,
BLUEMARK ID COLOR, BLUEMARK ID, BLUEMARK CLED, THERMOMARK PRIME, THERMOMARK CARD 2.0,
THERMOMARK CARD, mounting type: snap into tall marker groove, for terminal block width: 5.2 mm, lettering field
size: 4.6 x 10.5 mm, Number of individual labels: 72
03/12/2021 Page
16 / 18
Accessories
Zack marker strip, Strip, white, unlabeled, can be labeled with: PLOTMARK, CMS-P1-PLOTTER, mounting type:
snap into tall marker groove, for terminal block width: 15.2 mm, lettering field size: 10.5 x 15.1 mm, Number of
individual labels: 5
Test plug terminal block
Test plugs, with solder connection up to 1 mm² conductor cross section, color: gray
Spare parts
Relay base RIF-1…, for miniature power relay with 1 or 2 changeover contacts or solid-state relays of the same
design, Push-in connection, plug-in option for input/interference suppression modules, for mounting on NS 35/7,5
Plug-in miniature power relay, with power contact for high continuous currents, 1 changeover contact, input voltage
12 V DC
Plug-in module, for mounting on RIF-1, RIF-2, RIF-3, and RIF-4, with freewheeling diode and yellow LED, polarity:
A1+, A2-, input voltage: 12 … 24 V DC ±30%
03/12/2021 Page
17 / 18
Accessories
Relay retaining bracket, with ejector function and holder for marking material, suitable for RIF-1 relay base, for 16 mm
tall miniature power relay and solid-state relay
Phoenix Contact 2021 © – all rights reserved
PHOENIX CONTACT GmbH & Co. KG
Flachsmarktstr. 8
32825 Blomberg
Germany
Tel. +49 5235 300
Fax +49 5235 3 41200
03/12/2021 Page
18 / 18
