STMicroelectronics-HDMI05-CL02F3
| Part # | STMicroelectronics-HDMI05-CL02F3 |
Download  | STMicroelectronics-HDMI05-CL02F3 |
HDMI05-CL02F3
5-line I
P
A
D™, HDMI™
control line ESD protection
Features
■
Low line capacitance: 12 pF max.
■
High efficiency in ESD protection
■
Lead-free package
■
Very thin package
Flip Chip
9 bumps
■
High reliability offered by monolithic integration
■
High reduction of parasitic elements through
integration and wafer level packaging
Figure 1.
Pin configuration (bump side)
Complies with the standards:
3
2
1
■
IEC 61000-4-2 Level 4
–
–
15 kV (air discharge)
8 kV (contact discharge)
5V
CEC
SCL
A
B
C
■
IEC 61000-4-2 Level 1
RPU2
RPU
SDA
HPD
GND
GND
–
–
2 kV (air discharge)
2 kV (contact discharge)
Application
Where ESD protection for HDMI control lines
(CEC, HPD, SCL and SDA) is required:
Figure 2.
Schematic
■
Mobile phones and communication systems
■
Portable multimedia players
A1
5V
CEC
A2
■
Camcorder, digital still cameras
SCL
SDA
HPD
A3
B3
C3
Description
The HDMI05-CL02F3 chip is a low capacitance
ESD protection for HDMI control pins. It also
integrates pull-up resistor for I²C bus and pull-
down resistor for hot plug detect and pull-up
resistor for CEC line.
B1
B2 and C2 are ground pins
C1
The ESD protection circuitry prevents damage to
the protected device when subjected to ESD
surges up to 15 k
V
.
TM
: IPAD is a trademark of STMicroelectronics. HDMI, the
HDMI logo and High-Definition Multimedia
Interface
are trademarks or registered trademarks of
HDMI
Licensing LLC.
April 2010
Doc ID 15516 Rev 2
1/9
9
Characteristics
HDMI05-CL02F3
1
Characteristics
Table 1.
Symbol
Absolute maximum ratings (T
amb
= 25 °C)
Parameter
Value
Unit
External pins (A1, A2, A3, B3 and C3):
ESD IEC 61000-4-2, level 4 – air discharge
ESD IEC 61000-4-2, level 4 – contact discharge
Internal pins (B1, C1):
15
8
V
PP
kV
ESD IEC 61000-4-2, level 1 – air discharge
ESD IEC 61000-4-2, level 1 – contact discharge
2
2
Pd
T
op
T
stg
Line resistance power dissipation at 70 °C
Operating temperature range
60
mW
°C
-30 to + 85
-55 to + 150
Storage temperature range
°C
Figure 3.
Electrical characteristics (definitions)
I
Symbol
V
BR
Parameter
Breakdown voltage
Leakage current @ V
RM
Stand-off voltage
Clamping voltage
Dynamic impedance
Peak pulse current
Breakdown current
=
=
=
=
=
=
=
I
F
I
RM
V
RM
V
CL
R
d
I
PP
I
R
V
F
V
CL
V
BR
V
RM
V
I
RM
I
R
α
T
V
F
C
line
R
I/O
=
=
=
=
Voltage temperature coefficient
Forward voltage drop
Line capacitance
Slope = 1/Rd
I
PP
Series resistance between Input
Table 2.
Symbol
Electrical characteristics (T
amb
= 25 °C)
Test condition
Min.
Typ.
Max.
Unit
V
BR
I
RM
I
R
= 1 mA
6
20
200
1925
120
32
V
V
RM
= 3 V per line
50
1750
100
27
nA
Ω
R
1
, R
2
R
3
1575
80
k
Ω
k
Ω
R
4
22
V
line
= 0
V
, V
osc
= 30 m
V
, F = 1
M
Hz
CEC to GND with R
PU2
not connected
14
24
17
29
C
line
pF
pF
SCL and SDA
to GND with R
PU
not connected
(measured under zero light conditions)
V
line
= 0
V
, V
osc
= 30 m
V
, F = 1
M
Hz
CEC, SCL and SDA to GND with R
PU
and R
PU2
grounded
(1)
C
line
10
12
(measured under zero light conditions)
1. This
is the line capacitance seen by the data signals in the application conditions
Doc ID 15516 Rev 2
2/9
HDMI05-CL02F3
Characteristics
Figure 4.
S21(dB) versus frequency
Figure 5.
Analog crosstalk measurements
dB
dB
0.00
0.00
–
5
.00
CEC
SDA
5V
SCL
HPD
–
4
0.00
–
1
0.00
–
1
5.00
–
2
0.00
–
8
0.00
–
CEC RPU2
–
SDA SCL
–
1
20.00
–
1
60.00
–
SCL RPU
–
HPD SCL
–
SCL CEC
F(Hz)
F(Hz)
300.0k
1.0M
3.0M
10.0M 30.0M
100.0M 300.0M
1.0G
3.0G
300.0k
1.0M
3.0M
10.0M 30.0M
100.0M 300.0M
1.0G
3.0G
Figure 6.
ESD response to IEC 61000-4-2
(+8 kV contact discharge)
on CEC line
Figure 7.
10 V/div
ESD response to IEC 61000-4-2
(-8 kV contact discharge)
on CEC line
10 V/div
1
72 V
1
2
3
V
PP
: ESD peak voltage
V
CL
@ 30 ns: clamping voltage @ 30 ns
V
CL
@ 60 ns: clamping voltage @ 60 ns
2
52 V
3
39 V
3
-11 V
2
-17 V
1
V
PP
: ESD peak voltage
2
V
CL
@ 30 ns: clamping voltage @ 30 ns
3
V
CL
@ 60 ns: clamping voltage @ 60 ns
1
-52 V
20 ns/div
20 ns/div
Figure 8.
10 V/div
ESD response to IEC 61000-4-2
(+8 kV contact discharge)
on SCL line
Figure 9.
10 V/div
ESD response to IEC 61000-4-2
(-8 kV contact discharge)
on SCL line
1
V
PP
: ESD peak voltage
2
V
CL
@ 30 ns: clamping voltage @ 30 ns
3
V
CL
@ 60 ns: clamping voltage @ 60 ns
1
70 V
2
48 V
3
39 V
3
-11 V
2
-17 V
1
2
3
V
PP
: ESD peak voltage
V
CL
@ 30 ns: clamping voltage @ 30 ns
V
CL
@ 60 ns: clamping voltage @ 60 ns
-51 V
1
20 ns/div
20 ns/div
Doc ID 15516 Rev 2
3/9
Characteristics
HDMI05-CL02F3
Figure 10.
ESD response to IEC 61000-4-2
(+8 kV contact discharge)
on SDA line
Figure 11.
ESD response to IEC 61000-4-2
(-8 kV contact discharge)
on SDA line
10 V/div
10 V/div
1
79 V
1
V
PP
: ESD peak voltage
2
V
CL
@ 30 ns: clamping voltage @ 30 ns
3
V
CL
@ 60 ns: clamping voltage @ 60 ns
2
51 V
3
39 V
3
-14 V
2
-22 V
1
2
3
V
PP
: ESD peak voltage
V
CL
@ 30 ns: clamping voltage @ 30 ns
V
CL
@ 60 ns: clamping voltage @ 60 ns
1
-57 V
20 ns/div
20 ns/div
Figure 12.
ESD response to IEC 61000-4-2
(+8 kV contact discharge)
on HPD line
Figure 13.
ESD response to IEC 61000-4-2
(-8 kV contact discharge)
on HPD line
10 V/div
10 V/div
1
V
PP
: ESD peak voltage
2
V
CL
@ 30 ns: clamping voltage @ 30 ns
3
V
CL
@ 60 ns: clamping voltage @ 60 ns
49 V
2
1
65 V
3
40 V
3
-11 V
1
V
PP
: ESD peak voltage
2
V
CL
@ 30 ns: clamping voltage @ 30 ns
3
V
CL
@ 60 ns: clamping voltage @ 60 ns
2
-17 V
-43 V
1
20 ns/div
20 ns/div
Figure 14.
ESD response to IEC 61000-4-2
(+8 kV contact discharge)
on 5 V line
Figure 15.
ESD response to IEC 61000-4-2
(-8 kV contact discharge)
on 5 V line
10 V/div
10 V/div
2
52 V
72 V
1
1
V
PP
: ESD peak voltage
2
V
CL
@ 30 ns: clamping voltage @ 30 ns
3
V
CL
@ 60 ns: clamping voltage @ 60 ns
3
39 V
3
-14 V
2
-20 V
1
V
PP
: ESD peak voltage
2
V
CL
@ 30 ns: clamping voltage @ 30 ns
3
V
CL
@ 60 ns: clamping voltage @ 60 ns
1
-52 V
20 ns/div
20 ns/div
4/9
Doc ID 15516 Rev 2
HDMI05-CL02F3
Typical application schematic
2
Typical application schematic
Figure 16.
Implementation with HDMI
HDMI
Gnd
Gnd
Display
(T
V
,
f
lat panel,
monitor, projector)
TX2-
TX2+
TX2-
TX2+
Host
(Mobile Phone)
Gnd
TX
1
–
TX1+
Gnd
TX
1
–
TX1+
Gnd
Gnd
–
HDMIULC6 4F3
TX
0
–
TX0+
Gnd
T
C
–
TC+
TX
0
–
TX0+
Gnd
video
audio
video
T
C
–
audio
Multimedia
controller
Multimedia
controller
TC+
Ctrl /
status
Ctrl /
status
–
HDMI05
CL02F3
Gnd
Gnd
CEC
CEC
SCL
SDA
SCL
SDA
V
V
DD
_5V
D
D
_5V
HPD
HPD
Type C connector
Pi
n
–
out
B2
E2
J4
HDMIULC
6
–
4F3
A1 A3 C1 C3 D1 D3 F1 F3
4 TMDS channel
1
2
TMDS D
A
T
A
2 SHIELD
TMDS D
A
T
A
2 +
TMDS D
A
T
A
2-
TMDS D
A
T
A
1 SHIELD
TMDS D
A
T
A
1 +
TMDS D
A
T
A
1-
TMDS D
A
T
A
0 SHIELD
TMDS D
A
T
A
0 +
TMDS D
A
T
A
0-
TMDS CLK SHIELD
TMDS CLK +
TMDS CL
K
–
DDC / EEC GROUND
CEC
SCL
SDA
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
VDD_CEC
27K
5V
A1 A3 C1 C3 D1 D3 F1 F3
RESERVED
+5V POWER
HOT PLUG DETECT
2 x 1K75
5V
CEC
SCL
SDA
HPD
HDMIULC
6
–
4F3
B2
E2
100K
HDMI05-CL02F3
Doc ID 15516 Rev 2
5/9
Ordering information scheme
HDMI05-CL02F3
3
Ordering information scheme
Figure 17.
Ordering information scheme
HDMI 05
–
CL 02
F3
Function
HDMI = HDMI Protection
Number of lines
05 = 5 lines
Application
CL = Control lines
Version
02 = with CEC Pull-up integrated
Package
F3 = Flip Chip 0.4 mm pitch
4
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
®
®
ECO
P
A
CK packages,
depending on their level of environmental compliance. ECO
P
A
CK
®
ECO
P
A
CK is
an ST trademark.
Figure 18.
Flip Chip dimensions
400 µm
40
605 µm
55
255 µm
40
1.14 mm
30 µm
6/9
Doc ID 15516 Rev 2
HDMI05-CL02F3
Package information
Figure 19.
Footprint
Figure 20.
Marking
Dot, ST logo
xx = marking
z = manufacturing location
yww = datecode
(y = year
Copper pad Diameter:
220 µm recommended
260 µm maximum
ww = week)
E
Solder mask opening:
300 µm minimum
x x z
Solder stencil opening :
220 µm recommended
y
w w
Figure 21.
Flip Chip tape and reel specification
Ø 1.5
0.1
4.0 0.1
T
T
ST
4.0 0.1
1.24
0.69 0.05
User direction of unreeling
All dimensions in mm
Doc ID 15516 Rev 2
7/9
Ordering information
HDMI05-CL02F3
5
Ordering information
Table 3.
Order code
HDMI05-CL02F3
Ordering information
Marking
Package
Weight
Base qty
Delivery mode
JG
Flip Chip
1.76 mg
5000
T
a
pe and reel (7”)
6
Revision history
Table 4.
Date
Document revision history
Revision
Changes
24-Mar-2009
07-Apr-2010
1
2
First issue.
8/9
Doc ID 15516 Rev 2
HDMI05-CL02F3
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS “AUTOMOTIVE
GRADE” MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics – All rights reserved
STMicroelectronics group of companies
Australia – Belgium – Brazil – Canada – China – Czech Republic – Finland – France – Germany – Hong Kong – India – Israel – Italy – Japan –
Malaysia – Malta – Morocco – Philippines – Singapore – Spain – Sweden – Switzerland – United Kingdom – United States of America
Doc ID 15516 Rev 2
9/9
