STMicroelectronics-STIPN1M50-H
| Part # | STMicroelectronics-STIPN1M50-H |
Download  | STMicroelectronics-STIPN1M50-H |
STIPN1M50-H
Datasheet
SLLIMM-nano IPM, 3-phase inverter, 1 A, 3.6 Ω max., 500 V MOSFET
Features
•
IPM 1 A, 500
V
,
R
DS(on)
= 3.6 Ω, 3-phase MOSFET inverter bridge including
control ICs for gate driving
•
•
Optimized for low electromagnetic interference
3.3
V
, 5 V,
1
5 V CMOS/TTL input comparators with hysteresis and pull-down/
pull-up resistors
•
•
•
•
•
•
•
•
Undervoltage lockout
Internal bootstrap diode
Interlocking function
Shutdown function
Comparator for fault protection against overtemperature and overcurrent
Op-amp for advanced current sensing
Optimized pinout for easy board layout
Up to ±2 kV ESD protection (HBM C = 100 p
F
, R =
1
.5 kΩ)
NDIP-26L
Applications
•
•
•
•
•
Description
This SLLIMM (small low-loss intelligent molded module) nano provides a compact,
high-performance AC motor drive in a simple, rugged design. It is composed of six
MOSFE
T
s
a
nd three half-bridge HVICs for gate driving, providing low
electromagnetic interference (EMI) characteristics with optimized switching speed.
The package is optimized for thermal performance and compactness in built-in motor
applications, or other low power applications where assembly space is limited. This
IPM includes an operational amplifier, completely uncommitted, and a comparator
that can be used to design a fast and efficient protection circuit. SLLIMM is a
trademark of STMicroelectronics.
Product status link
Product summary
Order code
STIPN1M50-H
IPN1M50-H
NDIP-26L
Tube
Marking
Package
Packing
DS11939
–
Rev 4
–
January 2020
For further information contact your local STMicroelectronics sales office.
STIPN1M50-H
Internal schematic diagram and pin configuration
1
Internal schematic diagram and pin configuration
Figure 1.
Internal schematic diagram
GND(
1
)
SD/OD(2 )
VccW(3 )
HinW(4 )
LinW(5 )
(26)
N
W
(25)W,OUT W
GND
HVG
(24)Vboot W
OUT
VCC
HIN
LVG
SD/OD
LIN
Vboot
OP+(
6
)
(23)
N
V
OPOUT(7 )
OP-(
8
)
GND
OP+
OPOUT
OP-
(22)
V
,
OUT V
HVG
OUT
LVG
VCC
HIN
VccV(9 )
SD/OD
LIN
Vboot
HinV(10 )
LinV(11 )
Cin(12 )
(21)Vboot V
(20)
N
U
GND
CIN
HVG
OUT
LVG
VccU(13 )
HinU(14 )
SD/OD(15 )
LinU(16 )
(19)U,OUT U
(18
)
P
VCC
HIN
SD/OD
LIN
Vboot
(17)Vboot U
ADG171120161035SA
DS11939
–
Rev 4
page 2/21
STIPN1M50-H
Internal schematic diagram and pin configuration
Table 1.
Pin description
Pin
1
Symbol
GND
Description
Ground
2
SD/OD
Shutdown logic input (active low) / open-drain (comparator output)
Low voltage power supply W phase
High-side logic input for W phase
Low-side logic input for W phase
Op-amp non inverting input
V
W
3
CC
4
HIN W
LIN W
OP+
5
6
OP
7
Op-amp output
OUT
8
OP-
Op-amp inverting input
V
V
9
Low voltage power supply V phase
High-side logic input for V phase
Low-side logic input for V phase
Comparator input
CC
10
11
12
13
14
15
16
17
18
19
HIN V
LIN V
CIN
V
U
Low voltage power supply for U phase
High-side logic input for U phase
Shutdown logic input (active low) / open-drain (comparator output)
Low-side logic input for U phase
Bootstrap voltage for U phase
Positive DC input
CC
HIN U
SD/OD
LIN U
V
U
BOOT
P
U, OUT
U phase output
U
N
20
21
22
23
24
25
26
Negative DC input for U phase
Bootstrap voltage for V phase
V phase output
U
V
V
BOOT
V,
O
UT
V
N
Negative DC input for V phase
Bootstrap voltage for W phase
W phase output
V
V
W
BOOT
W, OUT
W
N
W
Negative DC input for W phase
DS11939
–
Rev 4
page 3/21
STIPN1M50-H
Internal schematic diagram and pin configuration
Figure 2.
Pin layout (top view)
PIN17
(*)
(*)
PIN26
PIN #1 ID
PIN16
PIN1
(*) Dummy pin internally connected to P (positive DC input).
AM09368V1
DS11939
–
Rev 4
page 4/21
STIPN1M50-H
Electrical ratings
2
Electrical ratings
2.1
Absolute maximum ratings
Table 2.
Inverter part
Parameter
Symbol
Value
Unit
MOSFET blocking voltage (or drain-source voltage)
V
DSS
500
V
IN
± I
Continuous drain current each MOSFET (T
= 25 °C)
1
2
A
A
D
C
± I
DP
Peak drain current each MOSFET (less than 1 ms)
P
T
o
tal power dissipation for each MOSFET (T
= 25 °C)
10.8
W
TOT
C
1. Applied
between HINi, LINi and GND for i = U, V, W.
2. Pulse
width limited by max. junction temperature.
Table 3.
Control part
Symbol
Parameter
Output voltage applied between OUT
, OUT
, OUT
– GND
Min.
– 21
Max.
Unit
V
V
V
V
+ 0.3
boot
OUT
U
V
W
boot
V
Low voltage power supply
Comparator input voltage
Op-amp non-inverting input
Op-amp inverting input
Bootstrap voltage
– 0.3
– 0.3
– 0.3
– 0.3
– 0.3
– 0.3
– 0.3
21
+ 0.3
V
CC
V
V
V
CIN
CC
CC
CC
V
V
V
+ 0.3
+ 0.3
V
op+
V
V
op-
V
620
V
boot
V
Logic input voltage applied between HIN, LIN and GND
Open-drain voltage
15
15
50
V
IN
V
V
T/SD/OD
dV /dt
out
Allowed output slew rate
V/ns
Table 4.
Total system
Parameter
Symbol
Value
Unit
Isolation withstand voltage applied between each pin and heat sink plate
(AC voltage, t = 60 s)
V
1000
Vrms
ISO
T
Power chip operating junction temperature range
Module case operation temperature range
-40 to 150
-40 to 125
°C
°C
J
T
C
DS11939
–
Rev 4
page 5/21
STIPN1M50-H
Thermal data
2.2
Thermal data
Table 5.
Thermal data
Parameter
Symbol
Value
Unit
°C/W
°C/W
R
Thermal resistance junction-case single MOSFET
Thermal resistance junction-ambient (per module)
11.5
22
th(j-c)
th(j-a)
R
DS11939
–
Rev 4
page 6/21
STIPN1M50-H
Electrical characteristics
3
Electrical characteristics
T
J
= 25 °C unless otherwise specified.
3.1
Inverter part
Table 6.
Static
Test conditions
Symbol
Parameter
Min.
Typ.
Max.
Unit
Zero-gate voltage drain
current
I
V
= 500
V
, V
=
1
5 V; V
= 15 V
Boot
1
mA
DSS
DS
CC
V
V
V
V
= V
= 15 V,
CC
boot
Drain-source breakdown
voltage
V
500
V
(BR)DSS
IN
D
= V
= 15 V,
boot
CC
Static drain source turn-
on resistance
R
3.2
0.9
3.6
1.6
Ω
V
DS(on)
IN
D
V
(1)
= 0 “logic state”,
= 1 A
Drain-source diode
forward voltage
IN
V
SD
I
D
1. Applied
between HINx, LINx and GND for x=U,V,W.
Table 7.
Inductive load switching time and energy
Symbol
Parameter
Turn-on time
Test conditions
Min.
Typ.
226
130
248
56
Max.
Unit
t
–
–
–
–
–
–
–
–
–
–
on
t
Crossover time (on)
Turn-off time
c(on)
V
V
V
= 300
V
,
DD
t
off
ns
= V
= 15
V
,
CC
boot
t
Crossover time (off)
Reverse recovery time
c(off)
(2)
= 0 to 5 V ,
IN
t
155
rr
I
= 0.5 A
C
Turn-on switching
energy
E
–
–
25
–
–
on
µJ
Turn-off switching
energy
E
3.8
off
1.
t
and t
include the propagation delay time of the internal drive. t
and t
are the switching time of MOSFET
C(OFF)
ON
OFF
C(ON)
itself under the internally given gate driving conditions.
2. Applied
between HINx, LINx and GND for x=U,V,W.
DS11939
–
Rev 4
page 7/21
STIPN1M50-H
Inverter part
Figure 3.
Switching time test circuit
GIPD161120151702RV
Figure 4.
Switching time definition
100% I
D
100%
I
D
t
rr
V
DS
I
D
I
D
V
DS
V
IN
V
IN
t
ON
t
OFF
t
C(OFF)
t
C(ON)
10%
V
DS
10%
I
D
V
IN(ON)
V
IN(OFF)
10% I
D
90%
I
D
10%
V
DS
(a) turn-on
(b) turn-off
AM09223V2
Figure 4. Switching time definition
refers to HIN, LIN inputs (active high).
DS11939
–
Rev 4
page 8/21
STIPN1M50-H
Control part
3.2
Control part
Table 8.
Low voltage power supply (V
CC
= 15 V unless otherwise specified)
Symbol
Parameter
UV hysteresis
Test conditions
Min.
1.2
Typ.
1.5
Max.
1.8
Unit
V
V
V
CC
V
CC
V
CC
CC_hys
V
UV turn ON threshold
UV turn OFF threshold
11.5
10
12
12.5
11
V
CC_thON
V
10.5
V
CC_thOFF
V
= 15 V, SD/OD = 5 V;
CC
Undervoltage quiescent supply
current
I
150
µA
qccu
LIN = 0 V; HIN = 0 V,
CIN = 0 V
V
= 15 V, SD/OD = 5 V;
CC
I
Quiescent current
1
mA
V
qcc
LIN = 0 V; HIN = 0 V,
CIN = 0 V
Internal comparator (CIN)
reference voltage
V
0.5
0.54
0.58
ref
Table 9.
Bootstrapped voltage (V
CC
= 15 V unless otherwise specified)
Symbol
Parameter
UV hysteresis
Test conditions
Min.
1.2
Typ.
1.5
Max.
1.8
Unit
V
V
V
BS
V
BS
V
BS
BS_hys
V
UV turn-ON threshold
UV turn-OFF threshold
11.1
9.8
11.5
10
12.1
10.6
V
BS_thON
V
V
BS_thOFF
V
< 9
V
,
S
D/OD = 5 V;
BS
Undervoltage V
quiescent
BS
I
70
110
300
µA
QBSU
LIN = 0 V and HIN = 5 V;
CIN = 0 V
current
V
= 15
V
,
S
D/OD = 5 V;
BS
I
V
quiescent current
BS
200
120
µA
Ω
QBS
LIN = 0 V and HIN = 5 V;
CIN = 0 V
R
Bootstrap driver on- resistance
LVG ON
DS(on)
DS11939
–
Rev 4
page 9/21
STIPN1M50-H
Control part
Table 10.
Logic inputs (V
CC
= 15 V unless otherwise specified)
Symbol
Parameter
Low logic level voltage
High logic level voltage
Test conditions
Min.
Typ.
Max.
Unit
V
V
0.8
il
V
2.25
20
V
ih
I
HIN logic “1” input bias current
HIN = 15 V
HIN logic “0” input bias current
HIN = 0 V
LIN logic “1” input bias current
LIN = 15 V
LIN logic “0” input bias current
LIN = 0 V
SD logic “0” input bias current
SD = 15 V
SD logic “1” input bias current
SD = 0 V
40
40
100
1
µA
µA
µA
µA
µA
µA
HINh
I
HINI
I
20
30
100
1
LINh
I
LINI
I
120
300
3
SDh
I
SDI
Dt
Dead time
180
ns
Table 11.
Op-amp characteristics (V
CC
= 15 V unless otherwise specified)
Symbol
Parameter
Test conditions
= 0
V
, V
= 7.5 V
Min.
Typ.
Max.
6
Unit
mV
nA
V
V
V
Input offset voltage
Input offset current
io
ic
o
I
4
100
75
40
io
= 0
V
, V
= 7.5 V
ic
o
Low level output voltage
High level output voltage
I
200
150
nA
ib
V
R =
10 kΩ to V
L CC
mV
V
OL
V
OH
R =
10 kΩ to GND
14
16
50
2.5
8
14.7
30
L
Source, V
= +1 V; V
= 0 V
mA
mA
V/µs
MHz
dB
id
o
Output short-circuit
current
I
o
Sink, V
= -1 V; V
= V
CC
80
id
o
V =
1 – 4 V; C
= 100 pF; unity gain
SR
Slew rate
3.8
12
i
L
V =
7.5 V
GBWP
Gain bandwidth product
Large signal voltage gain
o
A
vd
R =
2 kΩ
70
85
L
Supply voltage rejection
ratio
vs. V
SVR
60
55
75
70
dB
dB
CC
Common mode rejection
ratio
CMRR
1. The
direction of input current is out of the IC.
DS11939
–
Rev 4
page 10/21
STIPN1M50-H
Control part
Table 12.
Sense comparator characteristics (V
CC
= 15 V unless otherwise specified)
Symbol
Parameter
Test conditions
= 1 V
CIN
Min.
Typ.
Max.
Unit
I
V
I
Input bias current
1
µA
ib
Open-drain low level
output voltage
V
= 3 mA
= 3 mA
0.5
V
od
od
Open-drain low level
output resistance
R
ON_OD
I
od
166
125
Ω
Comparator delay
Slew rate
R
PD_SD
kΩ
SD/OD pulled to 5 V through
100 kΩ resistor
t
90
60
130
ns
d_comp
C =
180 pF; R
= 5 kΩ
SR
V/µs
L
pu
Shutdown to high / low-
side driver propagation
delay
V
V
= 0, V
= V
,
OUT
boot
CC
t
50
50
125
200
200
250
sd
= 0 to 3.3 V
IN
ns
Comparator triggering to
high / low-side driver turn-
off propagation delay
Measured applying a voltage step
from 0 V to 3.3 V to pin CIN
t
isd
1. Equivalent
values as a result of the resistances of three drivers in parallel.
Table 13.
Truth table
Logic input (V )
Output
I
Condition
SD/OD
LIN
H
HIN
LVG
L
HVG
H
Shutdown enable half-bridge tri-state
Interlocking half-bridge tri-state
L
L
L
L
L
H
H
H
H
H
L
0 “logic state” half-bridge tri-state
1 “logic state” low-side direct driving
1 “logic state” high-side direct driving
L
L
L
H
L
H
L
H
L
1. X:
don’t care.
DS11939
–
Rev 4
page 11/21
STIPN1M50-H
Waveform definitions
3.3
Waveform definitions
Figure 5.
Dead time and interlocking waveform definitions
DS11939
–
Rev 4
page 12/21
STIPN1M50-H
Shutdown function
4
Shutdown function
The device is equipped with three half-bridge IC gate drivers and integrates a comparator for fault detection.
The comparator has an internal voltage reference V
REF
connected to the inverting input, while the non-inverting
input pin (CIN) can be connected to an external shunt resistor for current monitoring.
Since the comparator is embedded in the U IC gate driver, in case of fault it disables directly the U outputs,
whereas the shutdown of V and W IC gate drivers depends on the RC value of the external SD circuitry, which
fixes the disabling time.
For an effective design of the shutdown circuit, please refer to Application note AN4966.
Figure 6.
Shutdown timing waveforms
GADG250120171515FSR
V
REF
CI N
HIN or LIN
U
V, W
PROTECT ION
HVG
o
r L
V
G
SD/OD
or
T/SD/OD
A
B
open -drain gate
(internal)
A
B
∗
∗
∗
∗
≅
∗
∗
_
R
SD
and C
SD
external circuitry must be designed to ensure
Please refer to AN4966 for further details.
* R
NTC
to be considered only when the NTC is internally connected to the T/SD/OD pin.
DS11939
–
Rev 4
page 13/21
STIPN1M50-H
Application circuit example
5
Application circuit example
Figure 7.
Application circuit example
MICROCONTROLLE R
GADG181120160820SA
Application designers are free to use a different scheme according to the specifications of the device.
DS11939
–
Rev 4
page 14/21
STIPN1M50-H
Guidelines
5.1
Guidelines
•
Input signals HIN, LIN are active high logic. A 375 kΩ (typ.) pull-down resistor is built-in for each input.
T
o
avoid input signal oscillation, the wiring of each input should be as short as possible, and the use of RC
filters (R
1
, C
1
) on each input signal is suggested. The filters should be with a time constant of about 100 ns
and placed as close as possible to the IPM input pins.
•
The use of a bypass capacitor C
VCC
(aluminum or tantalum) can reduce the transient circuit demand on the
power supply. Also, to reduce any high-frequency switching noise distributed on the power lines, a
decoupling capacitor C
2
(100 to 220 n
F
,
w
ith low ESR and low ESL) should be placed as close as possible
to the V
cc
pin and in parallel with the bypass capacitor.
•
•
The use of an RC filter (R
SF
, C
SF
) is recommended to prevent protection circuit malfunction. The time
constant (R
SF
x C
SF
) should be set to 1 μs and the filter must be placed as close as possible to the CIN pin.
The SD is an input/output pin (open-drain type if it is used as output). The capacitor C
SD
of the filter on SD
should be fixed no higher than 3.3 nF in order to assure the SD activation time τ
A
≤ 500 ns. Besides, the
filter should be placed as close as possible to the SD pin.
•
The decoupling capacitor C
3
(from 100 to 220 n
F
,
c
eramic with low ESR and low ESL), in parallel with each
C
boot
, filters high-frequency disturbance. Both C
boot
and C
3
(if present) should be placed as close as
possible to the U,
V
, W
a
nd V
boot
pins. Bootstrap negative electrodes should be connected to U,
V
, W
terminals directly and separated from the main output wires.
•
•
To
a
void overvoltage on the V
cc
pin, a Zener diode (Dz1) can be used. Similarly on the V
boot
pin, a Zener
diode (Dz2) can be placed in parallel with each C
boot
.
The use of the decoupling capacitor C
4
(100 to 220 n
F
,
w
ith low ESR and low ESL) in parallel with the
electrolytic capacitor C
vdc
is useful to prevent surge destruction. Both capacitors C
4
and C
vdc
should be
placed as close as possible to the IPM (C
4
has priority over C
vdc
).
•
By integrating an application-specific type HVIC inside the module, direct coupling to the MCU terminals
without an opto-couplers is possible.
•
•
Low-inductance shunt resistors have to be used for phase leg current sensing.
In order to avoid malfunctions, the wiring on N pins, the shunt resistor and P
WR_GND
should be as short as
possible.
•
The connection of SGN_GND to PWR_GND on one point only (close to the shunt resistor terminal) can
reduce the impact of power ground fluctuation.
These guidelines ensure the specifications of the device for application designs. For further details, please refer to
the relevant application note.
Table 14.
Recommended operating conditions
Symbol
Parameter
Supply voltage
Test conditions
Min.
Typ. Max. Unit
V
Applied between P-Nu, Nv, Nw
300
15
400
18
V
V
PN
V
Applied between V
-GND
Control supply voltage
13.5
13
1
CC
CC
Applied between V
for i = U,
V
, W
-OUT
BOOTi i
V
High-side bias voltage
18
V
µs
BS
t
Blanking time to prevent arm-short
PWM input signal
For each input signal
-40 °C < T
< 100 °C
dead
C
f
25
kHz
°C
PWM
-40 °C < T
< 125 °C
J
T
C
Case operation temperature
100
DS11939
–
Rev 4
page 15/21
STIPN1M50-H
Package information
6
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK
packages,
depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product
6.1
NDIP-26L type C package information
Figure 8.
NDIP-26L type C package outline
8278949_7
DS11939
–
Rev 4
page 16/21
STIPN1M50-H
NDIP-26L type C package information
Table 15.
NDIP-26L type C mechanical data
mm
Dim.
Min.
Typ.
Max.
4.40
1.20
3.20
1.90
6.10
0.72
0.68
1.02
0.98
0.59
0.55
29.25
1.00
0.70
29.55
12.55
1.90
2.60
16.70
21.78
1.54
A
A1
A2
A3
A4
b
0.80
3.00
1.70
5.70
0.53
0.52
0.83
0.82
0.46
0.45
29.05
0.50
0.35
1.00
3.10
1.80
5.90
b1
b2
b3
c
0.60
0.90
c1
D
0.50
29.15
0.77
D1
D2
D3
E
0.53
12.35
1.70
12.45
1.80
e
e1
eB1
eB2
L
2.40
2.50
16.10
21.18
1.24
16.40
21.48
1.39
DS11939
–
Rev 4
page 17/21
STIPN1M50-H
NDIP-26L packing information
6.2
NDIP-26L packing information
Figure 9.
NDIP-26L tube (dimensions are in mm)
Notes:
1- Material: extrused/transparent PVC 0.80
±0.1
mm thickness 10E6~10E11/SQ PVC
2- General tolerance unless otherwise specified: ±0.25 mm
8313150_3
Table 16.
Shipping details
Parameter
Base quantity
Bulk quantity
Value
17 pieces
476 pieces
DS11939
–
Rev 4
page 18/21
STIPN1M50-H
Revision history
Table 17.
Document revision history
Changes
Date
Revision
18-Nov-2016
1
Initial release.
Modified features and description on cover page.
01-Feb-2017
2
Modified
T
a
ble 15: “Recommended operating conditions”
Modified
T
a
ble 3: “Inverter part”,
T
a
ble 6: “Thermal data”
and
T
a
ble 11: “Logic inputs (V
= 15 V unless otherwise specified)”
.
07-Jun-2017
3
CC
Minor text changes.
Modified title, features and applications in cover page.
28-Jan-2020
4
Minor text changes.
DS11939
–
Rev 4
page 19/21
STIPN1M50-H
Contents
Contents
Internal schematic diagram and pin configuration
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
2
Electrical ratings
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
5
Absolute maximum ratings
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Thermal data
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
Electrical characteristics
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
7
Inverter part
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
Control part
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
Waveform definitions
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
Shutdown function
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
Application circuit example
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
Guidelines
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
14
Package information
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
NDIP-26L type C package information
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
16
NDIP-26L packing information
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
17
Revision history
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
DS11939
–
Rev 4
page 20/21
STIPN1M50-H
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST
products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST
products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of
Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of S
T
.
F
or additional information about ST trademarks, please refer to
www.st.com/trademarks
. All other product or service
names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2020 STMicroelectronics – All rights reserved
DS11939
–
Rev 4
page 21/21
