TDK-B84142A0050R000

EMC filters  

2-line filters  

for converters and power electronics  

Series/Type:  

B84142A*R000/G075  

The following products presented in this data sheet are being withdrawn.  

Ordering Code  

Substitute Product  

Date of  

Withdrawal  

Deadline Last

 

Last  

Orders  

Shipments  

B84142A0060G075  

B84142A0060

R

000  

2019-06-21  

2019-09-30  

2019-12-31  

Please contact your nearest TDK sales office if you need support in selecting a suitable  

electronics.tdk.com/sales.  

2-line filters  

B84142A*R000/G075  

for converters and power electronics  

Power line filters for 1-phase systems  

Rated voltage V

R

: 250 V AC/DC  

Rated current I

R

: 10 A to 60 A  

Construction  

2-line filters  

Metal case  

Features  

High insertion loss  

Easy to install  

Degree of protection IP 20

1)

for *R000  

Very compact design  

Optimized for long motor cables  

and operation under full load  

ENEC, UL and cUL approval for B84142A*R000  

Typical applications  

Frequency converters for motor drives, e.g.  

ꢀ

ꢀ

ꢀ

ꢀ

ꢀ

elevators  

conveyor systems  

pumps  

traction systems  

HVAC systems (heating, ventilation and air  

conditioning)  

Power supplies  

DC applications  

Terminals  

Finger-safe terminal blocks  

Threaded studs  

Marking  

Marking on component:  

Manufacturer’s logo, ordering code, rated voltage, rated  

current, rated temperature, climatic category, date code,  

approvals  

Minimum data on packaging:  

Manufacturer’s logo, ordering code, quantity, date code  

1) According

 

to IEC 60529  

Please read

C

autions and warnings

a

nd  

I

m

po

r

tant notes

a

t the end of this document.  

Page 2 of 13  

2-line filters  

B84142A*R000/G075  

for converters and power electronics  

Typical circuit diagram  

Technical data and measuring conditions  

Rated voltage V

R  

Rated current I

R  

Test voltage V

test  

250 V AC (50/60 Hz) / 250 V DC  

Referred to 40

°

C rated temperature  

1770 V DC, 2 s (line/line)  

2700 V DC, 2 s (lines/case)  

Overload capability (thermal)  

1.5

ꢁ

I

R

for 3 min per hour or  

2.5

ꢁ

I

R

for 30 s per hour  

Leakage current l

LK  

At V

R

and 50 Hz  

Climatic category (IEC 60068-1)  

R000: 25/100/21 (

ꢀ

25

°

C/+100

°

C/21 days damp heat test)  

G075: 25/085/21 (

ꢀ

25

°

C/+85

°

C/21 days damp heat test)  

Approvals  

IEC 60939, UL 1283, CSA C22.2 No.8  

Characteristics and ordering codes  

Screw  

stud  

Approvals  

I

R  

Terminal  

cross section  

mm

2  

I

LK  

R

typ  

Approx. Ordering

 

code  

weight  

kg  

A

mA  

m

Ω  

V

R

= 250 V AC/DC  

10  

20  

30  

40  

50  

60  

60  

4

4

6

6

16  

16  

7.9 18  

7.9 10  

0.55  

1.0  

1.0  

1.0  

2.5  

B84142A0010R000  

×

×

×

×

×

×

ꢀ

×

×

×

×

×

×

×

×

×

×

B84142A0020R000  

B84142A0030R000  

B84142A0040R000  

B84142A0050R000  

B84142A0060R000  

B84142A0060G075  

7.9  

17  

26  

26  

26  

5

3.6  

2.6  

2.45 2.5  

1.4 2.5  

M6  

ꢀ

ꢀ

×

= Approval granted  

Please read

C

autions and warnings

a

nd  

I

m

po

r

tant notes

a

t the end of this document.  

Page 3 of 13  

2-line filters  

B84142A*R000/G075  

for converters and power electronics  

Dimensional drawings  

B84142A0010R000 (10 A)  

General tolerances according to ISO 2768

ꢀ

cL  

Dimensions in mm  

B84142A0020R000 (20 A)  

General tolerances according to ISO 2768

ꢀ

cL  

Dimensions in mm  

Please read

C

autions and warnings

a

nd  

I

m

po

r

tant notes

a

t the end of this document.  

Page 4 of 13  

2-line filters  

B84142A*R000/G075  

for converters and power electronics  

B84142A0030R000, B84142A0040R000 (30 A and 40 A)  

General tolerances according to ISO 2768

ꢀ

cL  

Dimensions in mm  

B84142A0050R000, B84142A0060R000 (50 A and 60 A)  

General tolerances according to ISO 2768

ꢀ

cL  

Dimensions in mm  

Please read

C

autions and warnings

a

nd  

I

m

po

r

tant notes

a

t the end of this document.  

Page 5 of 13  

2-line filters  

B84142A*R000/G075  

for converters and power electronics  

B84142A0060G075 (60 A)  

General tolerances according to ISO 2768

ꢀ

cL  

Dimensions in mm  

Please read

C

autions and warnings

a

nd  

I

m

po

r

tant notes

a

t the end of this document.  

Page 6 of 13  

2-line filters  

B84142A*R000/G075  

for converters and power electronics  

Insertion loss

(typical values at Z = 50

Ω

)  

Filters for 10 A  

Filters for 20 A  

Filters for 30 A  

Filters for 40 A  

Please read

C

autions and warnings

a

nd  

I

m

po

r

tant notes

a

t the end of this document.  

Page 7 of 13  

2-line filters  

B84142A*R000/G075  

for converters and power electronics  

Insertion loss

(typical values at Z = 50

Ω

)  

Filters for 50 A  

Filters for 60 A  

Please read

C

autions and warnings

a

nd  

I

m

po

r

tant notes

a

t the end of this document.  

Page 8 of 13  

2-line filters  

B84142A*R000/G075  

for converters and power electronics  

Cautions and warnings  

Please read all safety and warning notes carefully before installing the EMC filter and putting it  

into operation (see

 

). The same applies to the warning signs on the filter. Please ensure that  

the signs are not removed nor their legibility impaired by external influences.  

Death, serious bodily injury and substantial material damage to equipment may occur if the  

appropriate safety measures are not carried out or the warnings in the text are not observed.  

Using according to the terms  

The EMC filters may be used only for their intended application within the specified values in low-  

voltage networks in compliance with the instructions given in the data sheets and the data book.  

The conditions at the place of application must comply with all specifications for the filter used.  

Warning  

It shall be ensured that only qualified persons (electricity specialists) are engaged on work such  

as planning, assembly, installation, operation, repair and maintenance. They must be provided  

with the corresponding documentation.  

Danger of electric shock. EMC filters contain components that store an electric charge. Danger-  

ous voltages can continue to exist at the filter terminals for longer than five minutes even after  

the power has been switched off.  

The protective earth connections shall be the first to be made when the EMC filter is installed  

and the last to be disconnected. Depending on the magnitude of the leakage currents, the par-  

ticular specifications for making the protective-earth connection must be observed.  

Impermissible overloading of the EMC filter or filter, such as with circuits able to cause reso-  

nances, impermissible voltages at higher frequencies etc. can lead to bodily injury and death as  

well as cause substantial material damages (e.g. destruction of the filter housing).  

EMC filters and filters must be protected in the application against impermissible exceeding of  

the rated currents by overcurrent protective circuitry.  

In case of leakage currents >3.5 mA you shall mount the PE conductor stationary with the  

required cross section before beginning of operation and save it against disconnecting. For  

leakage currents I

L

1)

<10 mA the PE conductor must have a KU value

2)

of 4.5 A

3)

; for leakage  

currents I

L

≥

10 mA the PE conductor must have a KU value of 6.

4)  

Output chokes and output filters must be protected in the application against impermissible  

exceeding of the component temperature.  

The converter output frequency must be within the specified range to avoid resonances and  

uncontrolled warming of the output chokes and output filters.  

1) I

L

= leakage current let-go  

2) The

 

KU value (symbol KU) is a classification parameter of safety-referred failure types designed to ensure protection against hazardous  

body currents and excessive heating.  

3) A

 

value of KU = 4.5 with respect to interruptions is attained with: a) a permanently connected protective earth circuit

≥

2.5 mm

2  

connected via shroud connectors (IEC 60309

ꢀ

2) and b) a protective earth circuit.  

4) KU

 

= 6 with respect to interruptions is achieved for fixed

ꢀ

connection lines

≥

10 mm

2

where the type of connection and line layout  

correspond to the requirements for PEN conductors as specified in relevant standards.  

Please read

C

autions and warnings

a

nd  

I

m

po

r

tant notes

a

t the end of this document.  

Page 9 of 13  

2-line filters  

B84142A*R000/G075  

for converters and power electronics  

The table below summarizes the safety instructions that must be observed without fail. A detailed  

description can be found in the relevant chapters of the databook.  

Topic  

Instructions  

Reference chapter  

(data book),  

paragraph  

Selecting a filter  

When selecting a filter, it is mandatory to observe the

 

Selection guide for  

rated data of the equipment (such as its rated input  

current, rated voltage, harmonic content etc.) as well  

as the derating instructions in Chapters 9 and 10.  

converter filters  

Rated voltage  

When power distribution systems deviating from the  

Power distribution  

symmetric TN-S system it is to check the suitability of

 

systems,  

the EMC filters and the allowed voltages including the  

fault cases.  

7

Protection from  

residual voltages  

Discharge resistors  

Active parts must be discharged within 5 s to a Safety

 

regulations,  

voltage of less than 60 V (or 50

µ

C). If this limit

 

6.1  

cannot be observed due to the operating mode, the  

hazardous point must be permanently marked in a  

clearly visible way.  

Filters which are not permanently connected (e.g.  

when the test voltage is applied to the filter at the  

incoming goods inspection) must be discharged after  

the voltage has been switched off.  

Safety regulations,  

6.2  

Installing and  

removing of EMC  

filters  

When installing and removing our EMC filters, a Safety

 

regulations,  

voltage-free state must be set up and secured with

 

6.4  

observance of the five safety rules described in  

EN 50110-1.  

Installation  

Use in IT systems  

The special features of the IT system (“first fault case”

 

Power distribution  

and other fault cases) shall be observed.  

system (network  

types), 7.6  

Safety notes on  

leakage currents  

The filter leakage currents specified in the data book

 

Leakage current,  

are intended for user information only.The maximum

 

8.4  

leakage current of the entire electrical equipment or

 

Leakage current,  

appliance has to be limited for safety reasons. Please

 

8.6  

obtain the applicable limits for your application from  

the relevant regulations, provisions and standards.  

Voltage derating  

If the permissible limits for the higher-frequency Voltage

 

derating,  

voltages at the filter are exceeded, the filter may be

 

9.8  

damaged or destroyed.  

Hazards caused by  

overloading the filters  

Current derating at  

elevated ambient  

temperatures  

Non-observance of the current derating may lead to

 

Current derating,  

overheating and consequently represents  

hazard.  

a fire 10.1  

Please read

C

autions and warnings

a

nd  

I

m

po

r

tant notes

a

t the end of this document.  

Page 10 of 13  

2-line filters  

B84142A*R000/G075  

for converters and power electronics  

Topic  

Instructions  

Reference chapter  

(data book),  

paragraph  

Protective earth  

connection at  

operating currents  

>250 A  

For operating currents greater than 250 A, we Mounting  

recommend the PE connection to be set up between

 

instructions, point  

the feed (filter: line) and output (filter: load) not via the  

PE terminal bolt in the filter housing.  

2

Mounting position  

Note the mounting position of the filters! It must Mounting  

always be ensured that natural convection is not instructions,

 

point  

impaired.  

13  

Long motor cables  

Long motor cables cause parasitic currents in the  

Mounting  

installation. The cable lengths indicated for the output

 

instructions, point  

chokes and output filters serve for orientation. The  

user must check the technical parameters and  

especially the choke temperatures for the respective  

application.  

15  

Display of ordering codes for EPCOS products  

The ordering code for one and the same product can be represented differently in data sheets,  

data books, other publications and the website of EPCOS, or in order-related documents such as  

shipping notes, order confirmations and product labels. The varying representations of the  

ordering codes are due to different processes employed and do not affect the specifications of the  

respective products. Detailed information can be found on the Internet under  

Please read

C

autions and warnings

a

nd  

I

m

po

r

tant notes

a

t the end of this document.  

Page 11 of 13  

2-line filters  

B84142A*R000/G075  

for converters and power electronics  

Symbols and terms  

Symbol  

English  

German  

α

Insertion loss  

Einfügungsdämpfung  

Bemessungskapazität  

Kapazität X-Kondensator  

Kapazität Y-Kondensator  

Spannungsabfall im Filter  

Spannungsanstiegsgeschwindigkeit  

Frequenz  

C

R  

C

X  

C

Y  

∆

V  

dv/dt  

f

Rated capacitance  

Capacitance X capacitor  

Capacitance Y capacitor  

Voltage drop (input to output)  

Rate of voltage rise  

Frequency  

f

M  

f

P  

Converter output frequency  

Pulse frequency  

Motorfrequenz  

Pulsfrequenz  

f

R  

f

res  

I

C  

I

LK  

I

max  

I

N  

Rated frequency  

Bemessungsfrequenz  

Resonanzfrequenz  

Strom durch Kondensator  

Filter-Ableitstrom  

Maximalstrom  

Nennstrom  

Resonant frequency  

Current through capacitor  

Filter leakage current  

Maximum current  

Nominal current  

I

op  

I

pk  

I

q  

I

R  

Operating current (design current)  

Rated peak withstand current  

Capacitive reactive current  

Rated current  

Betriebsstrom  

Bemessungs-Stoßstromfestigkeit  

Kapazitiver Blindstrom  

Bemessungsstrom  

I

S  

L

Interference current  

Inductance  

Störstrom  

Induktivität  

L

R  

L

stray  

P

L  

R

Rated inductance  

Stray inductance  

Power loss  

Resistance  

Bemessungsinduktivität  

Streuinduktivität  

Verlustleistung  

Widerstand  

R

is  

R

typ  

T

A  

T

max  

T

min  

T

R  

u

k  

V

eff  

V

K  

V

LE  

V

N  

V

R  

V

peak  

V

test  

V

X  

V

Y  

X

L  

Z

Insulation resistance  

DC resistance, typical value  

Ambient temperature  

Upper category temperature  

Lower category temperature  

Rated temperature  

Refered voltage drop in %  

RMS voltage  

Isolationswiderstand  

Gleichstromwiderstand, Richtwert  

Umgebungstemperatur  

Obere Kategorietemperatur  

Untere Kategorietemperatur  

Bemessungstemperatur  

Bezogener Spannungsabfall in %  

Effektivdivnung  

Voltage drop  

Spannungsabfall  

Voltage line to earth; voltage line to ground

 

Spannung Phase zu Erdpotential  

Nominal voltage  

Rated voltage  

Peak voltage  

Nenndivnung  

Bemessungsdivnung  

Spitzendivnung  

Test voltage  

Prüfdivnung  

Voltage over X capacitor  

Voltage over Y capacitor  

Inductive reactance  

Impedance  

Spannung über X-Kondensator  

Spannung über Y-Kondensator  

Induktiver Blindwiderstand  

Scheinwidertand  

|Z|  

Impedance, absolute value  

Scheinwiderstand (Betragswert)  

Please read

C

autions and warnings

a

nd  

I

m

po

r

tant notes

a

t the end of this document.  

Page 12 of 13  

Important notes  

The following applies to all products named in this publication:  

1.

Some parts of this publication contain

statements about the suitability of our products for certain  

areas of application

. These statements are based on our knowledge of typical requirements that are  

often placed on our products in the areas of application concerned. We nevertheless expressly point  

out

that such statements cannot be regarded as binding statements about the suitability of our  

products for a particular customer application.

As a rule we are either unfamiliar with individual  

customer applications or less familiar with them than the customers themselves. For these reasons, it is  

always ultimately incumbent on the customer to check and decide whether a product with the properties  

described in the product specification is suitable for use in a particular customer application.  

2.

We also point out that

in individual cases, a malfunction of electronic components or failure  

before the end of their usual service life cannot be completely ruled out in the current state of the  

art, even if they are operated as specified.

In customer applications requiring a very high level of  

operational safety and especially in customer applications in which the malfunction or failure of an  

electronic component could endanger human life or health (e.g. in accident prevention or life-saving  

systems), it must therefore be ensured by means of suitable design of the customer application or other  

action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or  

damage is sustained by third parties in the event of malfunction or failure of an electronic component.  

3.

The warnings, cautions and product-specific notes must b

e

observed.  

4.

In order to satisfy certain technical requirements,

some of the products described in this publication  

may contain substances subject to restrictions in certain jurisdictions (e.g. because they are  

classed as hazardous)

. Useful information on this will be found in our Material Data Sheets on the  

contact our sales offices.  

5.

We constantly strive to improve our products. Consequently,

the products described in this  

publication may change from time to time

. The same is true of the corresponding product  

specifications. Please check therefore to what extent product descriptions and specifications contained  

in this publication are still applicable before or when you place an order.  

We also

reserve the right to discontinue production and delivery of products

. Consequently, we  

cannot guarantee that all products named in this publication will

 

always be available.

 

The  

aforementioned does not apply in the case of individual agreements deviating from the foregoing for  

customer-specific products.  

6.

Unless otherwise agreed in individual contracts,

all orders are subject to our General Terms and  

Conditions of Supply.  

7.

Our manufacturing sites serving the automotive business apply the IATF 16949 standard.

The  

IATF certifications confirm our compliance with requirements regarding the quality management system  

in the automotive industry. Referring to customer requirements and customer specific requirements  

(“CSR”) TDK always has and will continue to have the policy of respecting individual agreements. Even  

if IATF 16949 may appear to support the acceptance of unilateral requirements, we hereby like to  

emphasize that

only requirements mutually agreed upon can and will be implemented in our  

Quality Management System.

For clarification purposes we like to point out that obligations from IATF  

16949 shall only become legally binding if individually agreed upon.  

8.

The trade names EPCOS, CeraCharge, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP, CTVS,  

DeltaCap, DigiSiMic, ExoCore, FilterCap, FormFit, LeaXield, MiniBlue, MiniCell, MKD, MKK, MotorCap,  

PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, PowerHap, PQSine, PQvar, SIFERRIT, SIFI,  

SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, ThermoFuse, WindCap are  

trademarks registered or pending

in Europe and in other countries. Further information will be found  

Release 2018-10  

Page 13 of 13