TDK-MPZ1005S121HT000
| Part # | TDK-MPZ1005S121HT000 |
Download  | TDK-MPZ1005S121HT000 |
E M C
C o m p o n e n t s
December 2016
Chip beads
For power line
MPZ series
MPZ100
5
T
y
pe
MPZ1005
1005[0402 inch]*
* Dimensions code JIS[EIA]
(2/10)
E M C
C o m p o n e n t s
Reminders for using these products
Before using these products, be sure to request the delivery specifications.
Safety reminders
Please pay sufficient attention to the warnings for safe designing when using this products.
Reminders
The storage period is less than 12 months.Be sure to follow the storage conditions (temperature:5 to 40°C, humidity:10 to 75% RH or
less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifediv shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equip-
ment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equip-
ment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or qual-
ity require a more stringent level of safety or reliabilit
y
,
o
r whose failure, malfunction or trouble could cause serious damage to societ
y
,
person or propert
y
.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/aviation equipment
(8) Public information-processing equipment
(9) Military equipment
(2)
T
r
ansportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
ꢀꢀ
(6) Seabed equipment
(13) Other applications that are not considered general-purpose
applications
(7)
T
r
ansportation control equipment
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing pro-
tection circuit/device or providing backup circuits in your equipment.
20161205 / beads_commercial_power_mpz1005_en.
(3/10)
E M C
C o m p o n e n t s
Product compatible with RoHS directive
Halogen-free
Chip beads
For power line
Compatible with lead-free solders
Overview of MPZ1005 type
FEATURES
Noise reduction solution for power line.
Compared to the MMZ series, has low direct current resistance for compatibility with large currents, optimal for low power consumption.
Various frequency characteristics with 2 materials of different features for countermeasures against everything from general signals to
high-speed signals.
Performs well even in signal lines where low direct current resistance is required.
APPLICATION
Noise removal for mobile devices such as smartphones and tablet terminals, and various modules.
Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment.
PART NUMBER CONSTRUCTION
MPZ
1005
S
100
C
T
000
L×W×T dimensions
(mm)
Impedance
(
) at 100MHz
Characteristic
Series name
Material name
Packaging style
Internal code
type
1005
1.0×0.5×0.5
S
Y
100
121
10
120
C
T
T
a
ping
000
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature ranges
Package quantity
Individual weight
Operating
temperature
Storage
temperature
Type
(pieces/reel)
（
°C
）
（
°C
）
（
mg
）
MPZ1005
–55 to +125
–55 to +125
10,000
1
The storage temperature range is for after the circuit board is mounted.
Halogen-free: indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20161205 / beads_commercial_power_mpz1005_en.
(4/10)
E M C
C o m p o n e n t s
MPZ1005 type
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T4
T3
T3
T2
t3
t2
T1
t1
t:
Time
Preheating
Temp.
T1
Soldering
Temp.
T3
Peak
Temp.
T4
Time
t1
60 to 120s
Time
t2
30 to 60s
Time
t3
10s
T2
180°C
150°C
230°C
250 to 260°C
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20161205 / beads_commercial_power_mpz1005_en.
(5/10)
E M C
C o m p o n e n t s
MPZ1005 type
MATERIAL CHARACTERISTIC
S material:
Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in
which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz.
Y material:
High frequency range type intended for the 100MHz region and above. For signal line applications in which the signal
frequency is far from the cutoff frequenc
y
.
I
mpedance values selected for effectiveness at 80 to 400MHz.
TYPICAL MATERIAL IMPEDANCE CHARACTERISTICS
ꢀ
2500
2000
Y
1500
1000
S
500
0
10
100
1000
Frequency(MHz)
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20161205 / beads_commercial_power_mpz1005_en.
(6/10)
E M C
C o m p o n e n t s
MPZ1005 type
SHAPE & DIMENSIONS
1 0.05
0.1min.
Dimensions in mm
RECOMMENDED LAND PATTERN
0.5
0.4
0.5
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20161205 / beads_commercial_power_mpz1005_en.
(7/10)
E M C
C o m p o n e n t s
MPZ1005 type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated current
Impedance
DC resistance
Part No.
[100MHz]
(
)
10
30
60
120
90
Tolerance
5
10
25%
25%
(
)max.
0.025
0.035
0.060
0.090
0.100
(A)max.
3.0
1.7
1.5
1.2
MPZ1005S100CT000
MPZ1005S300CT000
MPZ1005S600CT000
MPZ1005S121CT000
MPZ1005Y900CT000
25%
1.2
Please refer to the graph of rated current vs. temperature characteristics (derating) about the rating current at 85°C or more in temperature of the product.
○
Measurement equipment
Measurement item
Product No.
Manufacturer
Impedance
DC resistance
E4991A+16192A
T
y
pe-7556
Keysight
T
e
chnologies
Y
o
kogawa
＊
Equivalent measurement equipment may be used.
○
Rated current vs. temperature characteristics (derating)
3
.5
S
100C
3
2.5
2
S3
00C
1.5
S
600C
S
121C,Y900C
1
0.5
0
–55 –
3
5 –15
5
25
45
65
)
8
5 105
125
(
Temper
a
t
u
re °C
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20161205 / beads_commercial_power_mpz1005_en.
(8/10)
E M C
C o m p o n e n t s
MPZ1005 type
ELECTRICAL CHARACTERISTICS
Z VS. FREQUENCY CHARACTERISTICS (BY SERIES)
MPZ1005S series
MPZ1005Y series
250
200
150
100
50
250
MPZ1005Y900C
200
MPZ1005S121C
MPZ1005S600C
MPZ1005S300C
MPZ1005S100C
150
100
50
0
0
1
10
100
1000
)
10000
1
10
100
1000
)
10000
(
(
Frequency MHz
Frequency MHz
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20161205 / beads_commercial_power_mpz1005_en.
(9/10)
E M C
C o m p o n e n t s
MPZ1005 type
ELECTRICAL CHARACTERISTICS
Z, X, R VS. FREQUENCY CHARACTERISTICS
MPZ1005S100CT000
MPZ1005S300CT000
MPZ1005S600CT000
18
16
14
12
10
8
6
4
2
0
50
40
30
20
10
0
100
80
60
40
20
0
Z
Z
Z
R
R
R
X
X
X
1
10
100
1000
10000
1
10
100
1000
10000
1
10
100
1000
( )
Frequency MHz
10000
(
)
(
)
Frequency MHz
Frequency MHz
MPZ1005S121CT000
MPZ1005Y900CT000
200
250
200
150
100
50
Z
150
100
50
Z
R
R
X
X
0
0
1
10
100
1000
)
10000
1
10
100
1000
( )
Frequency MHz
10000
(
Frequency MHz
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20161205 / beads_commercial_power_mpz1005_en.
(10/10)
E M C
C o m p o n e n t s
MPZ1005 type
PACKAGING STYLE
REEL DIMENSIONS
2.0 0.5
1.0
+2.0
–0.0
8.4
ø13 0.2
ø21 0.8
14.4max.
ø180 2.0
Dimensions in mm
TAPE DIMENSIONS
1.
5
0
+0.1
2.0 0.05
4.0 0.1
A
P1
K
Dimensions in mm
K
T
y
pe
MPZ1005
A
B
P1
2.0 0.05
0.65 0.1
1.15 0.1
0.8max.
160min.
Taping
200min.
300min.
Drawing direction
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20161205 / beads_commercial_power_mpz1005_en.
