TDK-MPZ2012S102ATD25
| Part # | TDK-MPZ2012S102ATD25 |
Download  | TDK-MPZ2012S102ATD25 |
E M C
C o m p o n e n t s
May 2018
Chip beads
For power line
MPZ series (for automotive)
MPZ2012
type
MPZ2012
2012[0805 inch]*
* Dimensions code JIS[EIA]
(2/10)
E M C
C o m p o n e n t s
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using this products.
REMINDERS
The storage period is less than 12 months.Be sure to follow the storage conditions (temperature:5 to 40°C, humidity:10 to 75% RH or
less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifediv shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equip-
ment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equip-
ment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or qual-
ity require a more stringent level of safety or reliabilit
y
,
o
r whose failure, malfunction or trouble could cause serious damage to societ
y
,
person or propert
y
.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/aviation equipment
(8) Public information-processing equipment
(9) Military equipment
(2)
T
r
ansportation equipment (electric trains, ships, etc.)
(3) Medical equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
ꢀꢀ
(6) Seabed equipment
(13) Other applications that are not considered general-purpose
applications
(7)
T
r
ansportation control equipment
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing pro-
tection circuit/device or providing backup circuits in your equipment.
20180521 / beads_automotive_power_mpz2012_en.
(3/10)
E M C
C o m p o n e n t s
Product compatible with RoHS directive
Halogen-free
Chip beads
For power line
Compatible with lead-free solders
AEC-Q200
Overview of MPZ2012 type
FEATURES
Noise reduction solution for power line.
Compared to the MMZ series, has low direct current resistance for compatibility with large currents, optimal for low power consumption.
Performs well even in signal lines where low direct current resistance is required.
APPLICATION
Various ECUs, powertrains, body controls, and car multimedia (telematics).
PART NUMBER CONSTRUCTION
MPZ
2012
S
101
A
T
D25
L×W×T dimensions
(mm)
Impedance
(
) at 100MHz
Characteristic
Series name
Material name
Packaging style
Internal code
type
2012
2.0×1.25×0.85
S
101
100
A
T
T
a
ping
D25
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature ranges
Package quantity
Individual weight
Operating
temperature
Storage
temperature
Type
(pieces/reel)
（
°C
）
（
°C
）
（
mg
）
MPZ2012
–55 to +125
–55 to +125
4,000
8
The storage temperature range is for after the circuit board is mounted.
Halogen-free: indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20180521 / beads_automotive_power_mpz2012_en.
(4/10)
E M C
C o m p o n e n t s
MPZ2012 type
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T4
T3
T3
T2
t3
t2
T1
t1
t:
Time
Preheating
Temp.
T1
Soldering
Temp.
T3
Peak
Temp.
T4
Time
t1
60 to 120s
Time
t2
30 to 60s
Time
t3
10s
T2
180°C
150°C
230°C
250 to 260°C
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20180521 / beads_automotive_power_mpz2012_en.
(5/10)
E M C
C o m p o n e n t s
MPZ2012 type
MATERIAL CHARACTERISTIC
S material:
Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in
which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz.
TYPICAL MATERIAL IMPEDANCE CHARACTERISTICS
ꢀ
2500
2000
1500
1000
S
500
0
10
100
1000
Frequency(MHz)
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20180521 / beads_automotive_power_mpz2012_en.
(6/10)
E M C
C o m p o n e n t s
MPZ2012 type
SHAPE & DIMENSIONS
2.0 0.2
0.5 0.3
Dimensions in mm
RECOMMENDED LAND PATTERN
0.
8
1
0.
8
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20180521 / beads_automotive_power_mpz2012_en.
(7/10)
E M C
C o m p o n e n t s
MPZ2012 type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated current
Impedance
DC resistance
Part No.
[100MHz]
(
)
30
Tolerance
10
25%
25%
25%
(
)max.
0.010
0.020
0.040
0.050
0.100
0.150
(A)max.
6
4
3
2.5
2
1.5
MPZ2012S300
A
T
D25
MPZ2012S101
A
T
D25
MPZ2012S221
A
T
D25
MPZ2012S331
A
T
D25
MPZ2012S601
A
T
D25
MPZ2012S102
A
T
D25
100
220
330
600
1000
25%
25%
Please refer to the graph of rated current vs. temperature characteristics (derating) about the rating current at 85°C or more in temperature of the product.
○
Measurement equipment
Measurement item
Product No.
Manufacturer
Impedance
DC resistance
E4991A+16192A
T
y
pe-7556
Keysight
T
e
chnologies
Y
o
kogawa
＊
Equivalent measurement equipment may be used.
○
Rated current vs. temperature characteristics (derating)
7
S3
00A
6
5
S
101A
4
S
221A
3
S33
1A
S
601A
S
102A
2
1
0
–55 –
3
5 –15
5
25
45
65
8
5 105
125
(
)
Temper
a
t
u
re °C
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20180521 / beads_automotive_power_mpz2012_en.
(8/10)
E M C
C o m p o n e n t s
MPZ2012 type
ELECTRICAL CHARACTERISTICS
Z VS. FREQUENCY CHARACTERISTICS (BY SERIES)
MPZ2012S series
1200
1100
MPZ2012
S
221A
MPZ2012
S
102A
1000
MPZ2012
S
101A
900
MPZ2012
S3
00A
MPZ2012
S
601A
8
00
MPZ2012
S33
1A
700
600
500
400
3
00
200
100
0
1
10
100
1000
)
10000
(
Fre
qu
ency MHz
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20180521 / beads_automotive_power_mpz2012_en.
(9/10)
E M C
C o m p o n e n t s
MPZ2012 type
ELECTRICAL CHARACTERISTICS
Z, X, R VS. FREQUENCY CHARACTERISTICS
MPZ2012S300
A
T
D25
MPZ2012S101ATD25
MPZ2012S221
A
T
D25
50
40
140
120
100
8
0
3
00
250
Z
200
Z
3
0
20
10
0
Z
R
R
150
60
R
100
50
0
40
20
X
X
X
0
1
10
100
1000
)
10000
1
10
100
1000
( )
Fre
qu
ency MHz
10000
1
10
100
1000
)
10000
(
(
Fre
qu
ency MHz
Fre
qu
ency MHz
MPZ2012S331
A
T
D25
MPZ2012S601ATD25
MPZ2012S102
A
T
D25
400
3
50
3
00
250
200
150
100
50
700
600
1200
1000
Z
500
Z
800
Z
400
R
R
600
R
3
00
400
200
0
200
100
0
X
X
X
0
1
10
100
1000
10000
1
10
100
1000
10000
1
10
100
1000
)
10000
(
)
(
)
(
Fre
qu
ency MHz
Fre
qu
ency MHz
Frequency MHz
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20180521 / beads_automotive_power_mpz2012_en.
(10/10)
E M C
C o m p o n e n t s
MPZ2012 type
PACKAGING STYLE
REEL DIMENSIONS
2.0 0.5
1.0
+2.0
–0.0
8.4
ø13 0.2
ø21 0.8
14.4max.
ø180 2.0
Dimensions in mm
TAPE DIMENSIONS
1.
5
0
+0.1
2.0 0.05
4.0 0.1
A
P1
K
Dimensions in mm
K
T
y
pe
MPZ2012
A
B
2.3 0.2
P1
4.0 0.1
1.5 0.2
1.1max.
160min.
Taping
200min.
300min.
Drawing direction
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20180521 / beads_automotive_power_mpz2012_en.
