TE-Connectivity-1393277-8
| Part # | TE-Connectivity-1393277-8 |
Download  | TE-Connectivity-1393277-8 |
Automotive Relays
PCB Single Relays
Power Relay K (Open – Sealed)
n
n
n
n
Limiting continuous current 45A
Wide voltage range
24VDC coil versions available
For high current version refer to Power Relay K-S
Typical applications
ABS control, blower fans, car alarm, cooling fan, engine control, fuel pump,
hazard warning signal, heated front screen, heated rear screen, ignition,
lamps front/rear/fog light, interior lights, main switch/supply relay, seat
control, seatbelt pretensioner, sun roof, turn signal, valves, window lifter,
wiper control.
Contact Data
T
y
pical applications
Resistive/inductive
loads
1 form A, 1 NO
12VDC
Resistive/inductive
loads
1 form C, 1 CO
12VDC
Indicator lamps
Headlights,
capacitive loads
1 form A, 1 NO
12VDC
Headlights
capacitive loads
1 form C, 1 CO
12VDC
Contact arrangement
Rated voltage
1 form A, 1 NO
12VDC
A/B (NO/NC)
45/30A
A/B (NO/NC)
40/25A
Rated current
Limiting continuous current
23°C
45A
30A
40A
45A
30A
100A
60A
AgNi0.15
45/30A
30/25A
100/30A
60/30A
30A
25A
40A
25A
180A
60A
40/25A
25/20A
180/60A
60/30A
AgSnO
2
85°C
Limiting making current
1)
Limiting breaking current
2)
Contact material
120A
3)
60A
AgNi0.15
AgSnO
2
AgSnO
2
Min. recommended contact load
Initial voltage drop, at 10A, typ./max.
Operate/release time
Electrical endurance
1A at 5VDC
4)
20/300mV
typ. 5/3ms
5)
>2×10
5
ops.
at 13.5VDC, 40A
>2×10
5
ops.
at 13.5VDC, 40A
>10
7
ops.
>2.2×10
6
ops.
up to 8x21W
>10
5
ops.
up to 4x60W
>10
5
ops.
up to 4x60W
Mechanical endurance, DC coil
1) The
values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5VDC for 12VDC or 27VDC for 24VDC load voltages.
2) For
a load current duration of maximum 3s for a make/break ratio of 1:10.
3) Corresponds
to a peak inrush current on initial actuation (cold filament).
4) See
chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes/
5) For
unsuppressed relay coil. A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher
risk of contact tack welding.
Max. DC load breaking capacity
Load limit curve 1: arc extinguishes, during transit time (changeover contact).
Load limit curve 2: safe shutdown, no stationary arc (make contact).
Load limit curves measured with low inductive resistors verified for 1000 switching events.
1
11-2013, Rev. 1113
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
© 2013 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Automotive Relays
PCB Single Relays
Power Relay K (Open – Sealed)
(Continued)
Coil Data
Insulation Data
Rated coil voltage
12VDC / 24VDC
Initial dielectric strength
between open contacts
between contact and coil
500VAC
rms
500VAC
rms
Coil versions, DC coil
Coil
code
Rated
voltage
VDC
12
Operate
voltage
VDC
6.9
14.1
Release
voltage
VDC
1.2
2.4
Coil
resistance
Ω 10ꢀ
90
Rated coil
power
W
Other Data
001
022
1.6
1.6
EU RoHS/E
L
V
c
ompliance
Ambient temperature, DC coil
Climatic cycling with condensation,
EN ISO 6988
compliant
24
362
-40 to +85°C
6)
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Other coils on request.
3 cycles, storage 8/16h
T
e
mperature cycling (shock),
IEC 60068-2-14, Na
Damp heat cyclic,
IEC 60068-2-30, Db, Variant 1
Damp heat constant,
Coil operating range
20 cycles, -40/+85°C (dwell time 1h)
6 cycles, upper air temperature 55°C
TE0555-6
IEC 60068-2-3, method Ca
Degree of protection, IEC 61810
56 days, upper air temperature 55°C
RT 0/II – open version
RT III – immersion cleanable version
Corrosive gas,
IEC 60068-2-42
IEC 60068-2-43
10 days
10 days
Vibration resistance (functional),
IEC 60068-2-6 (sine pulse form),
acceleration, acc. to position
Shock resistance (functional),
10 to 200Hz, 20 to 40g
7)
IEC 60068-2-27 (half sine form single pulses),
acceleration, acc. to position
T
e
rminal type
8ms 30g
7)
PCB
Weight
sealed version
open version
approx. 22g (0.77oz)
approx. 19g (0.67oz)
Solderability (aging 3: 4h/155°C)
for leaded process (Tm = 183°C),
for Pb-free process (Tm = 217°C),
IEC 60068-2-20
Does not take into account the temperature rise due to the contact current
E = pre-energization
T
a
, method 1, hot dip 5s, 215°C
according IEC 600688
8)
Storage conditions
Packaging unit
sealed version
open version
525 pcs.
500 pcs.
6) See
coil operating range DC.
7) No
change in the switching state >10μs.
8) For
general storage and processing recommendations please refer to our Application
T
e
rminal Assignment (Open and Sealed Version)
Bottom view on solder pins
1 form A, 1 NO
*)
T
e
rminal 4 to be bridged
2
11-2013, Rev. 1113
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
© 2013 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Automotive Relays
PCB Single Relays
Power Relay K (Open – Sealed)
(Continued)
Dimensions
Power Relay K open version
Power Relay K sealed version
26.1 0.4
18.6 0.65
23.3 0.ꢀ
8.5 0.2
21.1 0.4
18.0 0.5
9.2 0.4
Assembly and
positioning aid
18.9 0.3
2.4 0.8
2.5 0.4
3.4 0.1
3.0 0.5
*)
2.5 – 3.0
*) additional tin tops
max. 1.5 mm
3.4 0.1
Terminals tinned
21.2 0.3
3.0 0.5
ꢀ*
2.5 – 3.0
0.55 0.25
Terminals tinned
ꢀ* additional
tin tops
max. 1.5 mm
Mounting Hole Layout
Bottom view on solder pins
Power Relay K open version
Power Relay K sealed version
16.0 0.3
16.0 0.3
10.2 0.2
6.0 0.2
10.2 0.2
6.0 0.
2
1.0 +0.05
ø 2.3 +0.1
ø 1.3 +0.1
ø 2.3 +0.1
1.3 +0.1
2.4
3.3 0.1
3.4 0.6
5.4
2.2 0.1
6.6 0.3
2.2 0.1
12.1 0.1
1.0 +0.05
ø 2.1 +0.1
3.3 0.1
12.1 0.1
ø 2.1 +0.1
ø 2.3 +0.1
2.3 0.2
ø 2.3 +0.1
ø 2.3 +0.1
2.3 0.2
ø 2.3 +0.1
13.3 0.2
13.3 0.
2
3
11-2013, Rev. 1113
© 2013 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
Automotive Relays
PCB Single Relays
Power Relay K (Open – Sealed)
(Continued)
Product code structure
T
y
pe
T
y
pical product code
V23076
-A
1
022
-C
13
3
V23076
Power Relay K, sealed
V23133
Power Relay K, open
T
e
rminal
A
PCB
Design
1
Single relay
12VDC
3
Single relay
24VDC
Coil
001
022
D
Contact type
C
Contact material
Single contact
Single contact
AgSnO
2
13
15
AgNi0.15
AgSnO
2
(Special)
14
Contact arrangement
2
1 form A, 1 NO
3
1 form C, 1 CO
Product code
T
e
rminal/Encl.
Design
Single relay
Coil
Contact
Single
Cont. material
Arrangement Part
number
V23076-A1001-C133
V23076-A1001-D143
V23076-A3001-C132
V23076-A3001-D142
V23076-A3001-D152
1)
V23076-A1022-C133
V23076-A1022-D143
V23076-A3022-C132
V23076-A3022-D142
V23133-A1001-C133
V23133-A1001-D143
V23133-A3001-C132
V23133-A3001-D142
V23133-A3001-D152
1)
V23133-A1022-C133
V23133-A1022-D143
V23133-A3022-C132
V23133-A3022-D142
V23133-A3022-D152
1)
1) For indicator lamps.
PCB, sealed
12VDC
AgNi0.15
AgSnO
2
1 form C, CO
1393277-4
1393277-6
AgNi0.15
AgSnO
2
AgSnO
2
special
AgNi0.15
AgSnO
2
1 form A, NO
1-1393277-4
1-1393277-7
1-1414175-0
1393277-8
24VDC
12VDC
1 form C, CO
1 form A, NO
1 form C, CO
1 form A, NO
1393277-9
AgNi0.15
AgSnO
2
AgNi0.15
AgSnO
2
AgNi0.15
AgSnO
2
1-1393277-8
1-1393277-9
1393278-7
PCB, open
1-1393278-3
5-1393278-7
5-1393278-9
1-1414173-0
3-1393278-7
3-1393278-9
7-1393278-1
7-1393278-2
1-1414174-0
AgSnO
2
special
AgNi0.15
AgSnO
2
24VDC
1 form C, CO
1 form A, NO
AgNi0.15
AgSnO
2
AgSnO
2
special
4
11-2013, Rev. 1113
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
© 2013 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
