TE-Connectivity-30-311-11A
| Part # | TE-Connectivity-30-311-11A |
Download  | TE-Connectivity-30-311-11A |
KISSLING
SINGLE POLE BI-STABLE RELAYS
Series 30 / 300A – from TE Connectivity (TE)
The series 30 bi-stable relay meets even the most difficult operating
requirements and is suited for various applications in severe conditions
on commercial vehicles, buses, construction & agricultural vehicles,
ground support equipment and fork lifts.
These relays are available with a wide variety of configuration options
including different contact configurations and coil voltages to have the
right product for your needs.
Other important advantages are low heat generation in the contact
area based on low contact voltage drop, a compact design, silver alloy
contact material and the use of mechanical and high thermal stability
insulating compounds. Both the terminals and the housing are protect-
ed against corrosion. Furthermore, our relays are characterized by high
shock and vibration characteristics and a low voltage drop.
Features
• Sealed housing conforms to IP6K9K
• Robust design
• Variety of configuration options
• 6G shock and 4G vibration resistant
By equipping the relays with blow-out magnets, contact voltages up to
250VDC are possible. The use of blow-out magnets is recommended
for contact voltages over 40VDC and blow-out magnets are also rec-
ommended for inductive load applications to maintain long contact life
at all voltages.
• Main contact current rated for continu-
ous current and 100% duty cycle
Applications
• Commercial vehicles
• Bus
• Lift truck
• Ground support equipment
• Construction and agricultural vehicles
Circuits
NO-Contact
Standard type
common –
NO-Contact
Special type reversed polarity
common +
NO/NC-Contact
NO-Contact
Auxiliary contact
/ Magnetic blowout
87y
88y
87b
88b
88a
87a
88
87
88
88a
88
88a
88
88a
85a
85b
86a
86b
86a
86b
86a
86b
85
86
85
85
Suppression diode
30-200-50
Suppression diode
30-200-59
Suppression diode
30-200-50
Suppression diode
30-200-50
Industrial & Commercial Transportation
/ Series 30 – 300A
Page 1
SERIES 30
300A
Specification
Technical Data
Temperature range
Protection
-40°C to +85°C
IEC 60529 / DIN 40050-9 / IP67 (0,2bar; 1min) and IP6K9K
6g / 11msec
Shock
Vibration
4g / 50 – 2000Hz
Thread sizes / Torque
M4 = 2.0 – 2.2Nm
|
M10 = 15 – 20Nm
Electrical Characteristics
Min. Insulation resistance
After live or environment
Dielectric withstanding voltage
Max. Contact drop, initial
Contact drop after life test
Continuous current
100M
Ω
50M
Ω
1050VAC / 1min at 50Hz
150mV
175mV
300A
Overload
2400A – 1sec / 600A – 20sec
Rated contact load
Resistive load
12 and 2
4
/
2
8VDC
50.000 cycles
300A
100.000 cycles
Mechanical life
Coil Data
12VDC
9-16VDC
12VDC
2
4
/
2
8VDC
18-32VDC
28VDC
24VDC NO/NC
18-32VDC
28VDC
36VDC
Voltage range
27-48VDC
36VDC
Nominal voltage
Pick up voltage
≥
9VDC
≥
7VDC
1.8
Ω
±ꢀꢁꢂꢃ
6.6A
≥
13VDC
≥
10VDC
7
.
8
Ω
±ꢀꢁꢂꢃ
3.0A
≥
13VDC
≥
10VDC
4.1
Ω
±ꢀꢁꢂꢃ
6.8A
≥
20VDC
≥
15VDC
18
Ω
±ꢀꢁꢂꢃ
approx. 1.9A
21.8
Ω
±ꢀꢁꢂꢃ
approx. 1.6A
50ms
Drop out voltage min.
Pull in coil resistance
Pull in current approx.
Drop out coil resistance
Drop out current approx.
Pick up impulse time approx.*
2.0
Ω
±ꢀꢁꢂꢃ
6.0A
8.4
Ω
±ꢀꢁꢂꢃ
2.8A
6.4
Ω
±ꢀꢁꢂꢃ
4.4A
50ms
50ms
50ms
Drop out impulse time approx.*
50ms
50ms
50ms
50ms
* (continuous
impulse max.1 min)
NO-Contact
max. 15msec
max. 5msec
max. 10msec
Changeover NO-Contact
Changeover NC-Contact
max. 30msec
Operating times
Operate
max. 25msec
max. 5msec
max. 20msec
Bounce
max. 8msec
Release
max. 35msec
Wire Section
Mounting position
min. 95mm
2
/ 0.147 sq.inch / AWG 4-0
optional
Industrial & Commercial Transportation
/ Series 30 – 300A
Page 2
SERIES 30
300A
Technical drawings
Standard side mounting
Short form side mounting
Long form side mounting
26
26
26
M10
M10 DIN 934
OPTIONAL
REPLACEABLE BARRIER
B10 DIN 137
M4x6 ISO 1207
Ø 50
84
Ø 50
62
Ø 50
55
50
40
58
85a
85b
85a
85b
85a
85b
86
86
86
Options:
Change-over NO/NC
Bottom mounting
Auxiliary contacts, magnetic blowouts
26
M10
26
M10 DIN 934
Optional
26
MAGNETIC
BLOWOUTS
REPLACEABLE
BARRIER
B10 DIN 137
M4x6 ISO 1207
Ø 50
Ø 50
AUXILIARY
CONTACT
B10 DIN 137
M10 DIN 934
M10
30
Ø 50
62
M4x6 ISO 1207
26
78
87
87a
Ø 6.5
62
50
50
62
50
64
Industrial & Commercial Transportation
/ Series 30 – 300A
Page 3
SERIES 30
300A
Ordering Information
Part Number
example: 30.311.02
30. 3 _ _. _ _ _
Current
Options
A
Auxiliary contacts*
Make and Break = 2A
2
Current 300A
Continuous current = 2AMP
Contacts
B
Magnetic blowout
(required over 40VDC)
1
Make contact NO
Change over NO/NC*
* Not possible for bottom mounting
2
Coil voltage
* Only mounting type 1 possible
1
12V
2
24
/
2
8V
Mounting
1
Standard side mounting
Suppression
2
3
4
Short form side
Bottom mounting
Long form side
0
1
Without suppression
With suppression
te.com
TE Connectivity, TE, TE connectivity (logo), KISSLING (logo) and KISSLING (word) are trademarks owned or licensed by the TE Connectivity
family of companies. All other logos, products and/or company names referred to herein might be trademarks of their respective owners.
The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be
reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use.
TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard Terms and Conditions of Sale for this product and in no case
will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product.
Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application.
© 2020 TE Connectivity | All Rights Reserved.
K1166709 | Version 08/2020
Industrial & Commercial Transportation
/ Series 30 – 300A
Page 4
