TE-Connectivity-9-1904064-4
| Part # | TE-Connectivity-9-1904064-4 |
Download  | TE-Connectivity-9-1904064-4 |
Automotive Relays
PCB Single Relays
Micro Relay K (THT – THR)
■
■
■
■
■
■
Small power relay
Limiting continuous current 20A at 85°C
Low weight
Low noise operation
Wave (THT) and reflow (THR/pin-in-paste) solderable versions
For double version refer to Double Micro Relay K
Typical applications
Door lock, heated front/rear screen, lamps front/rear/fog light, interior
lights, seat control, sun roof, window lifter, wiper control.
086C/R1_fcw1b
Contact Data
T
y
pical applications
Inductive load
V23086-*1*01-A403
1 form C, 1 CO
12VDC
Wiper load
V23086-*1*02-A803
1 form C, 1 CO
10VDC
Resistive/inductive load
V23086-*1*01-A402
1 form A, 1 NO
12VDC
Lamp load
V23086-*1*51-A502
1 form A, 1 NO
10VDC
Contact arrangement
Rated voltage
NO/NC
30/25A
NO/NC
30/25A
Rated current
1)
30A
15A
Limiting continuous current
1)
23°C
30/25A
20/15A
15/10A
40A
2)
30/25A
20/15A
30A
20A
15A
40A
2)
30A
15A
10A
85°C
105°C
Limiting making current
Limiting breaking current
Contact material
15/10A
40A
2)
100A
3)
30A
30A
30A
AgSnO
2
Min. contact load
>1A at 5VDC
4)
30/300mV
typ. 3/1.5ms
5)
Initial voltage drop at 10A, typ./max.
Operate/release time
Electrical enduranc
cyclic temperature -40°C, +25°C, +85°C
form C contact (CO) at 14VDC
motor reverse blocked,
25A, 0.77mH
wipe
r
,
25A make/5A break,
generator peak,
20A on NC,1mH
>1×10
6
ops.
>1×10
5
ops.
form A contact (NO) at 14VDC
Mechanical endurance
resistive 20A
>1×10
5
ops.
lamp 100A inrush,
10A steady state
>1×10
5
ops.
>5×10
6
ops.
1) Measured
on 70x70x1.5mm epoxy PCB FR4 with 25cm
2
(double layer 105μm)
copper area. Connecting cable cross section 6 mm
2
.Boundary conditions: 180°C coil
temperature;130°C solder joint.
Max. DC load breaking capacity
100
2) The
values apply to a resistive or inductive load with suitable spark suppression and at
maximum 13.5VDC for 12VDC load voltages. For a load current duration of maximum
3s for a make/break ratio of 1:10.
3) Corresponds
to the peak inrush current on initial actuation (cold filament).
4) See
chapter Diagnostics of Relays in our Application Notes or consult the internet at
5) Measured
at nominal voltage without coil suppression unit. A low resistive suppression
device in parallel to the relay coil increases the release time and reducesthe lifetime
caused by increased erosion and/or higher risk of contact tack welding.
curve I
curve II
10
0.1
1
10
100
Switching Current in A
Load limit curve 1: arc extinguishes, during transit time (changeover contact).
Load limit curve 2: safe shutdown, no stationary arc (make contact).
Load limit curves measured with low inductive resistors verified for 1000 switching events.
1
07-2017, Rev. 0717
© 2017 TE Connectivity.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
Automotive Relays
PCB Single Relays
Micro Relay K (THT – THR)
(Continued)
Coil Data
Other Data
Rated coil voltage
12VDC
EU RoHS/E
L
V
c
ompliance
Ambient temperature, DC coil
Cold storage, IEC 60068-2-1
Dry heat, IEC 60068-2-2
Climatic cycling with condensation,
EN ISO 6988
compliant
-40 to +105°C
1000h; -40°C
1000h; +125°C
Coil versions, DC coil
Coil
code
Rated
voltage
VDC
12
10
10
Operate
voltage
VDC
6.9
5.7
6.5
Release
voltage
VDC
1.5
1.25
Coil
resistance
Ω 10%
254
Rated coil
power
mW
0
567
0
552
20 cycles, storage 8/16h
100 cycles; -40/+125°C
35 cycles; -40/+125°C
6 cycles 25°C/55°C/93%RH
56 days 40°C/95%RH
001/801
002/802
051/851
T
e
mperature cycling (shock),
IEC 60068-2-14, Na
T
e
mperature cycling,
IEC 60068-2-14, Nb
Damp heat cyclic,
IEC 60068-2-30, Db, variant 1
Damp heat constant,
IEC 60068-2-3 method Ca
Degree of protection
TH
T
:
181
90
1.1
1111
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Coil operating range
300
250
Umax
RT III (61810)
RT II (61810)
Qc, method 2, 1min, 70°C
THR:
200
150
100
Sealing test, IEC 60068-2-17: THT
Corrosive gas
IEC 60068-2-42
10 days
10 days
IEC 60068-2-43
Vibration resistance (functional)
IEC 60068-2-6 (sine sweep)
Shock resistance (functional)
IEC 60068-2-27
(half sine)
T
e
rminal type
10 to 500Hz; 6g
6)
50
Uop (E=0V)
6ms, up to 30g
6)
PCB:TH
T
,
T
HR
approx. 4g (0.14oz)
0
-40
-20
0
20
40
60
80
100
120
Ambient temperature in °C
Weight
Does not take into account the temperature rise due to the contact current
E = pre-energization
Solderability (aging 3: 4h/155°C) THT
IEC 60068-2-20
Solderability THR
T
a
, method 1, hot dip 5s, 215°C
hot dip 5s 245°C
IEC60068-2-58
Insulation Data
Resistance to soldering heat
THT
IEC 60068-2-20
Initial dielectric strength
Tb, method 1A, hot dip 10s,
260°C with thermal screen
between open contacts
between contact and coil
500VAC
rms
500VAC
rms
Resistance to soldering heat
THR
IEC 60068-2-58
Storage conditions
260°C; preheating min 130°C
according IEC 60068-1
7)
2000 pcs.
Packaging unit
6) Depending
on mounting position: no change in the switching state >10μs.
7) For
general storage and processing recommendations please refer to our Application
2
07-2017, Rev. 0717
© 2017 TE Connectivity.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
Automotive Relays
PCB Single Relays
Micro Relay K (THT – THR)
(Continued)
T
e
rminal Assignment
Bottom view on solder pins
Mounting Hole Layout
Bottom view on solder pins
1 form A, 1 NO
1 form C, 1 CO
4
4
3
5
1
5
1
8.5
7.5
0.5
1.72
C
2
2
B
86ets_ab
86etw_ab
3
4
5
1
Dimensions
Micro Relay K, THT version
2
5 x
5 x
0.4
0.3
A
A
B
0.2
0.4
0.3
A
A
C
12.0
TE86etw_an1
5.8
0.1
0.2
0.2
2.5
0.6
Remark: Positional tolerances according to DIN EN ISO 5458
A
0.3
0.2
12.9
0.95
TE86etw_se
*) Additional tin tops max. 1 mm
*) Additional tin tops max. 1mm
3
07-2017, Rev. 0717
© 2017 TE Connectivity.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
Automotive Relays
PCB Single Relays
Micro Relay K (THT – THR)
(Continued)
Micro Relay K, THR version
Mounting Hole Layout
Bottom view on solder pins
86R1_DD2_2
86R1_VT3
View of Stand-Offs
Bottom view on solder pins
86R1_DD1_2
86R1_VT1
*) Additional tin tops max. 1mm
4
07-2017, Rev. 0717
© 2017 TE Connectivity.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
Automotive Relays
PCB Single Relays
Micro Relay K (THT – THR)
(Continued)
Product code structure
T
y
pe
T
y
pical product code
V23086
-C
1
001
-A
4
03
V23086
Micro Relay K (THT – THR)
T
e
rminal and enclosure
C
PCB version TH
T
,
s
ealed
R
PCB version THR, vented
Design
Coil
1
Single relay
001
801
051
Standard (THT)
Standard (THR)
Lamp load (THT)
002
802
851
Sensitive (THT)
Sensitive (THR)
Lamp load (THR)
Contact type
A
Single contact
Contact material index
4
5
AgSnO
2
standard
AgSnO
2
lamp load
8
AgSnO
2
wiper load
CO
Contact arrangement index
02
NO
03
Product code
V23086-C1001-A402
V23086-C1001-A403
V23086-C1051-A502
V23086-C1002-A803
V23086-R1801-A402
V23086-R1801-A403
V23086-R1851-A502
V23086-R1802-A803
Version
PCB TH
T
,
cleanable
Design
Single
Coil
Contact
Single
Cont. material
Arrangement
1 form A, 1 NO
1 form C, 1 CO
1 form A, 1 NO
1 form C, 1 CO
1 form A, 1 NO
1 form C, 1 CO
1 form A, 1 NO
1 form C, 1 CO
Part number
0-1393280-5
0-1393280-6
2-1904093-1
2-1414987-3
2-1904093-2
6-1414920-0
9-1904064-4
7-1414967-8
Standard
AgSnO
2
(standard)
Lamp load
Sensitive
Standard
AgSnO
2
(lamp)
AgSnO
2
(wiper)
AgSnO
2
(standard)
PCB THR,
vented
Lamp load
Sensitive
AgSnO
2
(lamp)
AgSnO
2
(wiper)
This list represents the most common types and does not show all variants covered by this datasheet.
Other types on request.
5
07-2017, Rev. 0717
© 2017 TE Connectivity.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
